Table of Contents
Advertisement
Simple Network Management Protocol (SNMP)
(3.1.1.38) proV1MSBstatusRtpRxError (Read-
Only)
RTP Rx Error
In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm) mode,
when fec_mode is "on," outputs the total number of
TS packets for which FEC correction was not possible
from the start of receiving (when proc start is
submitted) until the command is submitted.
The maximum output value is "255." That is to say,
when there are a total of 255 or more TS packet for
which FEC correction was not possible, the output is
"255."
This status value only is reset to zero when proc start is
submitted.
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
(3.1.1.39) proV1MSBstatusRtpRxSsrcNo (Read
Only)
RTP Rx SSRC Number
In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm) mode,
outputs the SSRC value of the RTCP packet currently
being received.
In sdi_to_asi/sdti-cp_to_asi mode, "--------" is output.
If no RTCP packets are received, "--------" is output.
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
(3.1.1.40) proV1MSBstatusRtcpRxCname
(Read-Only)
RTCP Rx CNAME
In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm) mode,
outputs the CNAME field value of the RTCP SDES
packet currently being received.
The output format is ASCII printable characters
(0x21≤x≤0x7d), with a maximum of 15 characters, left
aligned.
In sdi_to_asi/sdti-cp_to_asi mode, "--------" is output.
If no RTCP packets are received, "--------" is output.
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
(3.1.1.41) proV1MSBstatusRtpTx (Read-Only)
RTP Tx
In sdi_to_asi/sdti-cp_to_asi/tx-rx/tx-rx (cm) mode,
outputs the RTP packet transmission status.
In asi_to_sdi/asi_to_sdti-cp mode, outputs "--------" to
indicate that this is invalid.
If the rtp_tx command is "off," "off" is output.
If rtp_tx is "on," but for any reason transmission to the
network is stopped, "halt" is output.
If rtp_tx is "on," and RTP packets are being
transmitted to the network, "running" is output.
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
(3.1.1.42) proV1MSBstatusRtpTxPacket (Read-
Only)
RTP Tx Packet
In sdi_to_asi/sdti-cp_to_asi/tx-rx/tx-rx (cm) mode,
outputs the number of RTP packets output to the
network in the most recent one-second interval.
In asi_to_sdi/asi_to_sdti-cp mode, outputs "--------" to
indicate that this is invalid.
The maximum output value is "65535." That is to say,
if 65535 or more RTP packets are output in a second,
the output is "65535."
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
(3.1.1.43) proV1MSBstatusRtcpTxRr (Read-
Only)
RTCP Tx RR
In sdi_to_asi/sdti-cp_to_asi/tx-rx/tx-rx (cm) mode,
reports whether RTCP RR packets are received for the
RTP/RTCP packets currently being transmitted, as
follows:
If RR is being received: "alive"
If RR is not being received: "not alive"
In asi_to_sdi/asi_to_sdti-cp mode, outputs "--------" to
indicate that this is invalid.
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
106
Advertisement
Table of Contents
