Table of Contents
Advertisement
Simple Network Management Protocol (SNMP)
(3.1.1.32) proV1MSBstatusRtpRxPortNo
(Read-Only)
RTP Rx Port Number
In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm) mode, the
port No. of the rtp packets currently being received
(udp port) is output.
In sdi_to_asi/sdti-cp_to_asi mode, outputs "--------" to
indicate that this is invalid.
The permitted values are: 50000≤rx_port_no≤65534,
and rx_port_no=0.
For rx_port_no=0, to indicate that no rtp packets are
received, "--------" is output.
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
(3.1.1.33) proV1MSBstatusRtpRxPacket (Read-
Only)
RTP Rx Packet
In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm) mode,
outputs the number of RTP packets received from the
network in the most recent one-second interval.
In sdi_to_asi/sdti-cp_to_asi mode, outputs "--------" to
indicate that this is invalid.
The maximum output value is "65535." That is to say,
if 65535 or more RTP packets are input in a second,
the output is "65535."
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
(3.1.1.34) proV1MSBstatusRtpSeqError (Read-
Only)
RTP Sequence Error
In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm) mode,
outputs the number of RTP sequence discontinuities
detected in the most recent one-second interval.
In sdi_to_asi/sdti-cp_to_asi mode, outputs "--------" to
indicate that this is invalid.
The maximum output value is "255." That is to say, if
there are 255 or more RTP packet receiving errors are
in a second, the output is "255."
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
(3.1.1.35) proV1MSBstatusRtpRxFecMode
(Read-Only)
RTP Rx Fec Mode
In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm) mode,
indicates whether error correction is enabled or
disabled (fec_mode) for the RTP packets currently
being received.
In sdi_to_asi/sdti-cp_to_asi mode, outputs "--------" to
indicate that this is invalid.
If the stream has error correction, outputs "on", and if
the stream has no error correction, outputs "off."
When no RTP packets are received, "--------" is output.
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
(3.1.1.36) proV1MSBstatusTsCorrected (Read-
Only)
RTP TS Corrected
In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm) mode,
when fec_mode is "on," outputs the number of TS
packets in the most recent one-second interval
amended as a result of applying FEC correction.
When fec_mode is "off," or in asi_to_sdi/ asi_to_sdti-
cp mode, outputs "--------" to indicate that this is
invalid.
The maximum output value is "255." That is to say, if
FEC correction applies to 255 or more TS packets in a
second, the output is "255."
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
(3.1.1.37) proV1MSBstatusTsUncorrected
(Read-Only)
RTP TS Uncorrected
In asi_to_sdi/asi_to_sdti-cp/tx-rx/tx-rx (cm) mode,
when fec_mode is "on," outputs the number of TS
packets the most recent one-second interval for which
a correction by FEC was not possible.
When fec_mode is "off," or in sdi_to_asi/sdti-
cp_to_asi mode, outputs "--------" to indicate that this
is invalid.
The maximum output value is "255." That is to say, if
255 or more TS packets could not be corrected in a
second, the output is "255."
Note that when the MSBA-20IP board is not installed,
"RTP option is not mounted" is output.
105
Advertisement
Table of Contents
