Brbk-303 (Mx-107 Board) Circuit Description; Brbk-304 (Dv-33 Board) Circuit Description - Sony BRC-300 Service Manual
3ccd color video camera / optical multiplex unit
Hide thumbs
Also See for BRC-300:
- Command list (23 pages) ,
- Specifications (8 pages) ,
- Brochure & specs (8 pages)
Table of Contents
Advertisement
5-6. BRBK-303 (MX-107 Board) Circuit
Description
The BRBK-303 is installed in BRC-300/300P for optical
communication with BRU-300/300P.
Data Transmission
The data sent from BRC-300/300P is classified into two
groups, and then multiplexed by IC9005 to IC9008 into
16-bit data.
. Group 1
8-bit Y data
KEY (character data)
KEY BLK data (character's background)
TX (serial control data)
Remaining 4-bit: GND
. Group 2
8-bit CbCr data
H REF
C SYNC/V SYNC/H SYNC
FLD/VD/HD
6.75MHz clock
The gigabit transceiver converts multiplexed 16-bit data to
serial data with the 54 MHz clock, and then the laser
transceiver unit converts the serial data to an optical signal
and sends it to BRU-300/300P.
Data Reception
The laser transceiver unit converts the optical signal sent
from BRU-300/300P to electrical signal, and then the
gigabit transceiver separates it into the following signals
and sends them to BRC-300/300P.
INT/EXT
VD
RX (serial control data)
TEST signal
The gigabit transceiver restores 54 MHz clock from the
signals received, and then IC9002 divides the 54 MHz
clock into 27 MHz clock and sends it to BRC-300/300P as
a reference signal from BRU-300/300P.
Power Supply Circuit
DC voltages +12 V and CPU +3.3 V are supplied from
BRC-300/300P. Further, the DC-DC converter generates
+3.3 V DC and +2.5 V DC from the +12 V.
BRC-300/300P
BRU-300/300P
5-7. BRBK-304 (DV-33 Board) Circuit
Description
BRBK-304 converts the video signals sent from BRC-300/
300P or BRU-300/300P to DV format, and then outputs
the video signal on the i.LINK (IEEE1394) interface to
external device.
Video/Audio Signal Processing
The 8-bit video data Y and CbCr sent from BRC-300/300P
or BRU-300/300P are multiplexed by IC008, and are
converted to SMPTE125M-compliant video signal. SAV
(Start of Active Video) and EAV (End of Active Video)
codes are added to the video signal based on the FLD, VD
and HD signals. Then the video signal is output to the sync
detector IC401 (1/2).
In the sync detector IC401 (1/2), the FLD, VD and HD
signals are detected from SAV and EAV in the video
signal sent from IC008, and are then output to the DV
compressor IC206 together with the video signal.
The DV compressor IC206 compresses the signals from
IC401 (1/2) in a DV format, and then outputs them to the
i.LINK packet generator IC401 (2/2).
In the audio interleave IC301, the interleave processing in
a DV format of the mute signal is performed. Then the
audio data is output to the i.LINK packet generator IC401
(2/2).
The i.LINK packet generator IC401 (2/2) generates the
i.LINK isochronous packets (a 480-byte unit) from the
video/audio data sent from the DV compressor IC206 and
audio interleave IC301. At this time, additional informa-
tion data is input from the SP CPU IC603. The i.LINK
isochronous packets are output to the DV OUT connector
CN501 through the IEEE1394 controller IC506.
Synchronization and Clock
The timing generator IC303 generates sync signals (FLAT
and FLTT) and clock synchronizing with the frame signal
(SEL_FD) from IC206.
The video/audio data output from IC206 and IC301 are
communicated to the i.LINK packet generator IC401 (2/2)
in synchronization with these timing signals.
5-7
Hide quick links:
Advertisement
Table of Contents
