Table of Contents
Advertisement
30" Combination Installation
For High-Speed Oven / Single Wall Oven
For detailed product dimensions
and installation specifications, refer
to model-specific product page and
installation guide on web
30" High-Speed
Oven Cutout
For models:
E30SO75FPS
2"
E30SO75ESS
(visible
gap)*
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
* Minimum 2
/
"
5
8
clearance required
from bottom of
Built-In High-Speed
Oven cutout to top
edge of Wall Oven's
faceplate, leaving
a 2" visible gap
between both product
faceplates
** Critical dimension –
MUST be applied
Installation Specifications
30" Combination Installation Specifications
•
Always consult local and national electric codes. (Refer
to product-specific electrical specifications on this page.)
•
Minimum 24" deep cutout dimension is critical for proper
combination install ation, to ensure that each built-in
product's faceplate will fit flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2" required distance from bottom of
Wall Oven cutout to floor, 31" suggested.
•
Respect critical dimensions as noted for proper
installation of built-In products.
•
Minimum 23-1/4" clearance needed for Wall Oven
door depth when open.
24" min.
21
/
" min.
11
16
22
/
"max.
3
16
22
3
/
" min.
8
22
/
" max.
7
8
28
/
"min.
1
28
/
"min.
1
2
2
29" max.
28
/
"max.
7
8
31"
suggested
distance
4
/
"
1
2
min.
required
30" High-Speed Oven Specifications
•
Product Weight – (E30SO75FPS / E30SO75ESS) 115 Lbs.
•
Voltage Rating – 240V / 60 Hz / 15 or 20 Amps
•
Single phase 3- or 4-wire cable, 240 Volt, 60 Hertz AC
only electrical supply with ground required on separate
circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 Volts = 3.3 kW
•
Amps @ 240 Volts = 13.2 Amps
•
Full oven base of solid plywood or similar material
required, capable of supporting 150 Lbs.
•
Minimum 2-5/8" clearance required from bottom of High-
Speed Oven cutout to top edge of Wall Oven's faceplate,
leaving a 2" visible gap between both product faceplates.
30" Electric Single Wall Oven Specifications
•
Product Weights –
(E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208
Volt, 60 Hertz AC only electrical supply with ground
required on separate circuit fused on both sides of line.
•
Connected Load (kW Rating) @ 240 / 208 Volts =
4.0 / 3.0 kW
•
Amps @ 240 / 208 Volts = 16.6 / 14.4 Amps
•
Full oven base of solid plywood or similar material
required, capable of supporting 200 Lbs.
30"min.
240V/60Hz
grounded electrical
outlet should NOT
be located within
shaded area
20
/
"
1
4
Full plywood base
required to support
150 lbs.
16
3
/
"
4
C L
4"x 4" opening
to route armored
cable
24"min.**
(critical
dimension)
Full base required
to support 200 lbs.
3" max.
2" min.
Electrical junction
box location
Bottom cutout
edge must be
finish cut
e l e c t ro l u x i c o n . c o m
planning
information
For models:
High-Speed Oven
E30SO75FPS
E30SO75ESS
Single Wall Oven
E30EW75GPS
E30EW75GSS
Note:
For planning
purposes only. Refer
to Product Installation
Guide on the web at
electroluxicon.com for
detailed instructions.
Specifications subject
to change.
153
Hide quick links:
Advertisement
Table of Contents
