Sony Trimaster PVM-L2300 Operation Manual page 9
Lcd video monitor
Hide thumbs
Also See for Trimaster PVM-L2300:
- Operation manual (142 pages) ,
- Manual (20 pages) ,
- Product manual (18 pages)
Table of Contents
Advertisement
For setting the display, see "Selecting Display Mode" on
page 77.
Black frame insertion display mode
Motion blur caused by the holding-type display of the LCD
is decreased by inserting the black frame between the
picture frames in double frame rate (100/120Hz) operation
of the LCD panel.
For setting the display, see "Selecting Display Mode" on
page 77.
Available to a multi signal format
The monitor supports various input signals such as 720 ×
576/50i to 1920 × 1080/50P, 60P and variable computer
signals up to WUXGA (1920 × 1200). A DVI-D (HDCP
correspondence), HDMI* and four option slots are
equipped as the interface and the monitor supports HD-
SDI, SDI, RGB, YPbPr, Y/C, composite and Dual-link
HD-SDI signal input.
* HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
HD frame capture function
The frame of the HD-SDI input signal is captured and
saved as a picture file in the "Memory Stick". This is used
to confirm the color tone and picture angle of the current
scene and recorded scene by using the multi display
(Picture&Picture) function.
* As the frame of the input signal is captured, the data and
marker set by the monitor is not reflected.
For the operation, see "Capturing the Picture of the HD
Signal (HD Frame Capture)" on page 82.
Multi display function
Two kinds of input signals are output on the monitor. Side
by Side mode is useful for adjusting the color or comparing
two pictures.
For the operation, see "Displaying Two Signals on One
Screen (Picture&Picture)" on page 79.
Pixel zoom function
As part of the picture is magnified up to 8 times without
scaling processing, this is convenient for confirming a
minute part of the signal.
For the operation, see "Magnifying the Picture (Pixel
Zoom)" on page 80.
Safe area marker and aspect marker functions
The monitor is equipped with two area markers and center
marker as the safe area marker and aspect marker for
confirming the picture angle.
For the operation, see "Displaying the Area Marker or
Aspect Marker" on page 83.
Scan selection/Native scan display function
You can select from under scan (–3%), normal scan (0%)
and over scan (mask of the 5% over scan portion in the
normal scan) for the picture display.
The monitor is equipped with a native scan display
function which maps the pixel of the signal to the panel in
one-to-one mode. You can select the mode from ×1, ×2 or
Aspect Correction to display a signal in native mode. An
SD signal of non-square pixels (the number of H pixels of
the signal system is 720 or 1440) or a 640 × 480 SD signal
of DVI video/HDMI video is displayed correctly by
scaling processing of doubling for the V direction and
correct aspect ratio for the H direction, and the picture is
also optimized and displayed by modifying the aperture
coefficient value, filter coefficient value, etc. in Aspect
Correction mode.
For the operation, see "Selecting the Native Scan/Scan
Mode" on page 78.
Black detail mode display function
You can reduce to dull black color by backlight leaking and
precisely assess any parts with low color gradation.
You can decrease the black level up to 40% of the normal
2
display (100 cd/m
at 100% signal). The parts with high
color gradation (higher than 75 IRE) are clipped by the
dynamic range of the circuit, but a zebra pattern
(selectable) is displayed in the clipped portions.
For the operation, see "Displaying the Picture in Black
Detail Mode" on page 81.
Aspect selectable function
A squeezed and recorded signal is displayed with the
correct angle. You can select from 4:3 and 16:9 aspect
modes.
Remote control function (Ethernet control)
The controller controls up to 32 monitors by the Ethernet
(10BASE-T/100BASE-TX) connection. Up to four
controllers are connected to one monitor in single mode.
You can control individual monitors or monitor groups
simply by entering the monitor ID number or group ID
number. You can also execute the same operation on all
connected monitors, or put all connected monitors into the
same setup and adjustment state.
Closed caption display function
EIA/CEA-608 or EIA/CEA-708 standard closed caption
signals superimposed on the SDI signals are displayed by
installing the optional input adaptor (BKM-244CC).
Variable picture adjustment functions
Auto chroma, phase and matrix adjustment function are
equipped. The white balance is automatically adjusted by
9
Features
Advertisement
Table of Contents
