Siemens SINUMERIK 840D sl Programming Manual page 13
Measuring cycles
Hide thumbs
Also See for SINUMERIK 840D sl:
- Function manual (2184 pages) ,
- Programming manual (1334 pages) ,
- Commissioning manual (1102 pages)
Table of Contents
Advertisement
7.2.4
Description of the parameterizing cycles ................................................................................. 7-14
7.2.4.1
General information ................................................................................................................. 7-14
7.2.4.2
Setting additional parameters - CYCLE_PARA ....................................................................... 7-14
7.2.4.3
Calibrate tool probe - CYCLE_CAL_TOOLSETTER................................................................ 7-15
7.2.4.4
Calibration on surface - CYCLE_CAL_PROBE ....................................................................... 7-15
7.2.4.5
Calibration in groove - CYCLE_973......................................................................................... 7-16
7.2.4.6
Calibration in hole - CYCLE_976 ............................................................................................. 7-16
7.2.4.7
Measuring milling tools - CYCLE_971 ..................................................................................... 7-17
7.2.4.8
Measuring turning tools - CYCLE_972 .................................................................................... 7-17
7.2.4.9
Hole, measure shaft - CYCLE_977_979A............................................................................... 7-18
7.2.4.10 Groove, measure web - CYCLE_977_979B............................................................................ 7-18
7.2.4.11 Measure rectangle - CYCLE_977_979C.................................................................................. 7-19
7.2.4.12 Single-point measurement - CYCLE_978................................................................................ 7-20
7.2.4.13 Angle measurement - CYCLE_998.......................................................................................... 7-20
7.2.4.14 Corner measurement with specification of angles - CYCLE_961_W....................................... 7-20
7.2.4.15 Corner measurement with specification of points - CYCLE_961_P......................................... 7-21
7.2.4.16 Single-point measurement - CYCLE_974................................................................................ 7-22
7.2.4.17 Two-point measurement - CYCLE_994 ................................................................................... 7-23
7.3
Measuring cycle support in the program editor (from measuring cycles SW 6.2) ................... 7-24
7.3.1
Menus, explanation of the cycles............................................................................................. 7-24
7.3.1.1
General information ................................................................................................................. 7-24
7.3.1.2
Softkey bars for turning............................................................................................................ 7-25
7.3.1.3
Softkey bars for milling............................................................................................................. 7-27
7.3.1.4
Programming example............................................................................................................. 7-30
7.3.2
Pre-setting of the measuring cycle support ............................................................................. 7-31
7.4
Measuring result screens......................................................................................................... 7-34
8
Hardware/software.................................................................................................................................. 8-1
8.1
Hardware requirements ............................................................................................................. 8-1
8.1.1
General hardware prerequisites................................................................................................. 8-1
8.1.2
Measuring probe connection...................................................................................................... 8-1
8.1.2.1
General information ................................................................................................................... 8-1
8.1.2.2
SINUMERIK 810D, 840D powerline, 840Di............................................................................... 8-1
8.1.2.3
SINUMERIK 840D sl (solution line) probe connection to X122, NCU 7x0 ................................ 8-6
8.1.3
Measuring in JOG ...................................................................................................................... 8-7
8.2
Software requirements............................................................................................................... 8-7
8.2.1
How the measuring cycles are supplied .................................................................................... 8-7
8.2.2
Software versions NC and MMC/HMI........................................................................................ 8-7
8.2.3
Options....................................................................................................................................... 8-7
8.3
Function test............................................................................................................................... 8-8
9
Data description...................................................................................................................................... 9-1
9.1
Machine data for machine cycle runs ........................................................................................ 9-1
9.1.1
Machine data that configure the memory .................................................................................. 9-1
9.1.1.1
General information ................................................................................................................... 9-1
9.1.1.2
Memory configuring machine data, SRAM ................................................................................ 9-2
9.1.1.3
Memory configuring machine data, DRAM ................................................................................ 9-5
9.1.2
Other machine data ................................................................................................................... 9-6
9.2
Cycle data .................................................................................................................................. 9-8
9.2.1
Data blocks for measuring cycles .............................................................................................. 9-8
9.2.1.1
General information ................................................................................................................... 9-8
9.2.1.2
Data block GUD5.DEF............................................................................................................... 9-8
9.2.1.3
Data block GUD6.DEF............................................................................................................... 9-8
9.2.2
Data adjustment to a specific machine .................................................................................... 9-13
Measuring cycles
Programming Manual, Release 04/2006, 6FC5398-4BP10-0BA0
Table of contents
xiii
Advertisement
Table of Contents
