Turn Area On/Off; Turn All Areas On; Turn All Areas Off; Move To Area - Bosch solution 6000 Installation Manual
Hide thumbs
Also See for solution 6000:
- User manual (48 pages) ,
- Owner's manual (8 pages) ,
- Quick user manual (2 pages)
Table of Contents
Advertisement
Solution 6000
Installation Manual
Areas > Commands >
Turn Area On/Off
This command allows you to turn on or off areas. If an area
has already been turned All On or Part On, a 'tick' () will
be displayed on the right side of the area name.
1) Enter [MENU] + [2] + [0] + [1] and select the area
and press [OK] to change the current state.
A1 Security System
A2 Area 2 Name
A3 Area 3 Name
Press
OK or MENU
Areas > Commands >
Turn All Areas On
This command allows you to turn on all areas that your
PIN has been assigned to at the same time. An alternative
method for arming all areas is to enter your PIN then press
and hold the [ON] key for 2 seconds.
1) Enter [MENU] + [2] + [0] + [2]. The keypad will
display the exit time bar to prompt you to exit all
areas. You should leave all areas now.
When exit time has expired, the keypad will display
that all areas are turned All On (armed).
Area 1 Name
EXIT NOW
i
The display area icons option is programmable per
keypad. If this option has not been selected then area
Note
icons 1 to 8 will not be displayed. See Menu 6-1-5 —
Indicator Options.
Areas > Commands >
Turn All Areas Off
This command allows you to turn off all areas that your PIN
has been assigned to at the same time. This command
cannot be accessed from a keypad that is in the armed
state. An alternative method for disarming all areas is to
enter your PIN, then press and hold the [OFF] key for 2
seconds.
1) Enter [MENU] + [2] + [0] + [3] to disarm all areas.
6-2
Area Programming
-
-
MENU 2-0-1
-
-
MENU 2-0-2
-
-
MENU 2-0-3
Areas > Commands >
Move To Area
Each keypad on the system can operate any area, however
you can only operate the area which is currently being
displayed. This menu allows you to change the current
keypad view from one area to display another area.
An alternative method for changing the current area
being displayed is to enter your PIN and then press the
left or right arrow keys. Keep pressing the arrow key until
the desired area is displayed. Only areas which have been
assigned to the PIN will be available for view.
If you move to another area, the keypad will automatically
revert back to its assigned home area after 2 minutes. See
MENU 6-1-3 - Home Area.
1) Enter [MENU] + [2] + [0] + [4] and select the area
from the list and press [OK] to move to the selected
area.
A1 Security System
A2 Area 2 Name
A3 Area 3 Name
Press
OK or MENU
i
Turn off option - see MENU 6-1-2, PIN To Change Area
and just use the [←] and [→] keys to move through
Note
all areas on the system without the need to enter
your PIN.
Areas > Commands >
Chime On/Off
Chime mode allows you to monitor a zone (or group of
zones) by sounding the keypad buzzer or activating a
programmable output. This can be useful when you need
to monitor the front or back entrance to a premises while
in the disarmed state.
To select which zones will be monitored for chime, see
MENU 3-0-3 — Set Chime Zones.
1) To turn chime mode on or off, enter [MENU] + [2] +
[0] + [5] and select the area from the list then press
[OK].
Security System A1
Chime is OFF.
To turn ON, Press ON.
To Go Back Press OK
The chime tone will only be heard on keypads
i
programmed to sound the chime tone. See MENU
Note
6-1-5 — Chime Tone
-
-
MENU 2-0-4
-
-
-
MENU 2-0-5
Bosch Security Systems 07/14 BLCC610I
- Quick Links:
- Wiring Diagrams
Hide quick links:
Advertisement
Table of Contents
