Executing An Effect - Sony DFS-700 Service Manual
Dme switcher, digital/analog input board, analog composite input board, digital multi effects board, 3d video mapping effects board
Hide thumbs
Also See for DFS-700:
- Operating instructions manual (212 pages) ,
- Specifications (8 pages)
Table of Contents
Advertisement
Executing an Effect
To execute an effect, after setting the execution direction (normal/reverse),
in the effect transition section press the AUTO TRANS button, or move
the fader lever.
EDITOR
GPI
SET UP
MASK
SHIFT
AUXILIARY
BLACK
BACKGROUND
BLACK
FOREGROUND
BLACK
Using the fader lever
By moving the fader lever from one end of its travel to the other at any
desired speed, you can manually control the transition.
The transition indicator on the left of the fader lever lights progressively
corresponding to the status of the transition. When the transition
completes, the transition indicator goes completely off.
For an effect in which the image switches like a cut, the transition occurs
when the fader lever is in the center position.
Note
After powering on the system, move the fader lever once through the
whole of its travel. This will ensure that the fader lever operates correctly.
To pause the transition
Stop moving the fader lever.
To resume the transition
Start moving the fader lever again.
3-54
Chapter 3 Basic Operation
USER PGM
SNAP SHOT
TITLE
DSK
EDGE
1
2
STATUS EDIT
LUM
LUM
LUM
TRAIL
SHADOW
CRK
CRK
BORDER BEVELD
EDGE
INITIAL
EDIT
LEARN
MASK
MASK
SOFT
RECALL
CCR
LIGHTING
MATTES
BORDER
PATTERN
PAGE
F1
F2
F3
F4
F5
HOLD
LOCATION
ADJ
INPUT
EFFECT
TRANS RATE
DSK
PATTERN NUMBER
FTB
SET
SET
CCR
TITLE 1
TITLE 2
DSK
SUPER BG FRGD 2 MEMORY
FRAME
FREEZ
MIX
EFFECT
N/R
REV
DIRECT
DIRECT
DSK PVW
SOURCE
SOURCE
FILL
RECALL
PATTERN
LAST X
FADE
TO
7
8
9
INS
BLACK
1
2
3
4
5
6
7
8
MEMORY
INT
TITLE
VIDEO
4
5
6
DEL
1
2
3
4
5
6
7
8
INT
MEMORY
CUT
VIDEO
P IN P
DSK
1
2
3
RST
ENTER
DOWN
UP
0
AUTO
1
2
3
4
5
6
7
8
MEMORY
INT
VIDEO
TRANS
PATTERN/KEY PAD
Fader lever
AUTO TRANS button
Using the AUTO TRANS button
To execute the effect automatically at the preset transition time, press the
AUTO TRANS button, turning it on.
To pause the transition
During the transition, press the AUTO TRANS button, turning it off.
Note
If the fader lever is in an intermediate position, then the transition pauses
at the corresponding position. To make sure the transition does not pause,
first move the fader lever to either end of its travel.
To resume the transition
Press the AUTO TRANS button again.
Using the fader lever and AUTO TRANS button together
You can use the AUTO TRANS button to complete a transition started and
paused with the fader lever, or in the opposite way, use the fader lever to
complete a transition started and paused with the AUTO TRANS button.
• If you resume a transition partially executed with the fader lever, using
the AUTO TRANS button, then the transition time taken is in proportion
to the setting for the entire transition. For example, if the transition time
is set to 100 frames, and you carry out the equivalent of 25 frames with
the fader lever, then press the AUTO TRANS button, the remainder of
the transition will take 75 frames.
• If you partially execute the transition with the AUTO TRANS button,
then start moving the fader lever, the transition resumes when the fader
lever reaches the corresponding intermediate position.
Note
When you carry out an auto transition by controlling the processor unit
from an external editor through the EDITOR connector, then regardless of
the fader lever position, the transition is executed in its entirety.
3-55
Chapter 3 Basic Operation
- Quick Links:
- Manual Structure
Hide quick links:
Advertisement
Table of Contents
