Sony DFS-700 Service Manual page 24
Dme switcher, digital/analog input board, analog composite input board, digital multi effects board, 3d video mapping effects board
Hide thumbs
Also See for DFS-700:
- Operating instructions manual (212 pages) ,
- Specifications (8 pages)
Table of Contents
Advertisement
DME Switcher Introduction
Procedure
EDITOR
GPI
SET UP
SHIFT
2
AUXILIARY
3
BLACK
BACKGROUND
BLACK
FOREGROUND
BLACK
4
1
Pull the fader lever toward you as far as it will go.
<Preparation>
2
<Image selection>
Press the MATTES button in the menu control section, and display
page 1 of the MATTE menu, then with the F1(SELECT) button select
"INT V".
MATTE
1/2
PAGE
You can change the color of matte color and embossing pattern. For details,
see the section "Adjusting Color Mattes" (page 3-57).
3
Press the BACKGROUND bus INT VIDEO button.
The pressed button lights red, and a color matte is selected as the
background image.
4
Press the FOREGROUND bus button 1.
The pressed button lights amber, and the video signal connected to the
VIDEO INPUT 1 connector is selected as the foreground image.
5
<Effect selection>
Press the SET button to the right of the PATTERN NUMBER display
window, turning it on.
(If it is already lit, omit this step.)
3-6
Chapter 3 Basic Operation
8
5
USER PGM
SNAP SHOT
TITLE
DSK
EDGE
1
2
STATUS EDIT
LUM
LUM
LUM
TRAIL
SHADOW
CRK
CRK
BORDER BEVELD
EDGE
INITIAL
EDIT
LEARN
MASK
MASK
MASK
SOFT
RECALL
CCR
LIGHTING
MATTES
BORDER
PATTERN
PAGE
F1
F2
F3
F4
F5
LOCATION
HOLD
ADJ
INPUT
EFFECT
TRANS RATE
DSK
PATTERN NUMBER
FTB
SET
SET
CCR
TITLE 1
TITLE 2
DSK
SUPER BG FRGD 2 MEMORY
FRAME
FREEZ
MIX
EFFECT
N/R
REV
DIRECT
DIRECT
DSK PVW
RECALL
PATTERN
SOURCE
SOURCE
FILL
LAST X
FADE
TO
1
2
3
4
5
6
7
8
MEMORY
INT
TITLE
7
8
9
INS
BLACK
6
VIDEO
4
5
6
DEL
INT
1
2
3
4
5
6
7
8
MEMORY
CUT
VIDEO
P IN P
DSK
1
2
3
RST
7
DOWN
UP
ENTER
0
AUTO
INT
1
2
3
4
5
6
7
8
MEMORY
VIDEO
TRANS
PATTERN/KEY PAD
1,9
SELECT
Lum
Sat
Hue
CH2BRD
INT V
0-100
0-100
0-99
BRDMAT
F1
F2
F3
F4
F5
6
In the numeric keypad, press buttons 1, 1, 0, 0, in that order.
The TRANS RATE display window shows "1.1.0.0.".
7
Press the ENTER button.
The dots to the lower right of the digits disappear, and picture-in-
picture, or pattern number 1100, is selected.
8
<Border settings>
In the menu control section, press the BORDER button.
The button lights, enabling the border.
You can change the color and width of the border. For details, see the section
"Modifying the Boundary" (page 3-26).
<Effect execution>
9
Move the fader lever to the opposite end.
Both the BACKGROUND bus INT VIDEO button and the
FOREGROUND bus button 1 light red.
As you move the lever, the picture-in-picture effect takes place, and a
foreground image with a border is inserted into the background image.
Dots appear to the lower right of the digits.
3-7
Chapter 3 Basic Operation
- Quick Links:
- Manual Structure
Hide quick links:
Advertisement
Table of Contents
