Table of Contents
Advertisement
Available languages
Available languages
Put the grease, up to filling, in the 4
bearing supports (sleeve adjustment
and front paddle closing), use a grease
pump. Then clean up the excess. We
recommend using a lithium grease with
mineral oil base, viscosity ISO VG 100,
type LGMT2 (SKF) or AFB-LF (THK).
Annually
Washing the cover:
- padding (rear clamps and cuff clamp); take them off
the machine and proceed with washing and drying as
indicated on the instructions label, then put them
back to their original position. Check the wear of the
machine paddings and, if necessary, replace them,
to avoid leaving marks on clothes.
- cover for dummy: take it off the machine and proceed
with washing and drying as indicated on the
instructions label, then put it back to its original
position. If worn, please replace.
Check the sponge on cuff clamp. If it is worn, please
replace to avoid leaving marks on clothes.
BY QUALIFIED PERSONNEL
In order to proceed with the maintenance of the internal
parts of the machine, remove all panels to allow
access. All parts found damaged during control, must
be replaced. When finishing operation assemble all
parts back to their original position.
Six monyhly
Condensate trap:
Remove the filter from trap and
eliminate impurities using air or
compressed air. Check the proper
operation.
Adjust working pressure:
Check the correct adjustment of
the pressure-reducing air inside
the pneumatic panel by comparing
it with the instructions on the
manual-Technical Section.
Annually
Joints and taps: check the correct functioning making
sure there are no leaks.
Safety and instructions labels: check they are in good
shape and well visible.
ORDERING SPARE PARTS
Spare parts have to be ordered indicating the following
data in order to ensure a rapid despatch of the correct
parts:
General data
Client
______________________________
Machine
______________________________
Model
______________________________
Serial Number
______________________________
Spare part
Code
______________________________
Description
______________________________
Quantity
______________________________
IMPORTANT:
For
electrical
components
220V/230V/240V
50
Hz
specification plate of the defective part), add to the
order code the letter corresponding to the rating
required as given in the following table:
other
than
for
supply
(check
on
the
A
Example:
General datai
Client
Exemple
Machine
Shirt finishers
Model
A
Serial Number
110227
Spare part
Code
08301
Description
Vacuum unit
Quantity
1
The parts appearing in this manual without
accompanying code number ARE NOT AVAILABLE from
stock
For the code and description of the spare part refer to the
spare parts list (see Technical Section).
Data, descriptions and illustrations in this brochure are not
binding. The manufacturer reserves the right to make any
changes anytime without any obligation to update this
brochure.
STORAGE OR DEMOLITION
In case of a long period storage, it is necessary to
disconnect the hydraulics, electric and pneumatic feeding
sources.
Proceed as follows:
a) Drain the condensate tank, if existing, blowing
compressed air inside the steam inlet joint.
b) Turn off the steam/condensate taps, then disconnect
all connections.
c) Remove scale from copper tubes (see "Maintenance").
d) Drain the compressed air filter cup.
e) Close the compressed air feeding tap, then disconnect
the all connection.
f) Disconnect the main power line.
Locate the machine in a proper, dry and safe place; cover
it with a cloth to shelter from humidity and dust (see
"Safety warnings").
According to article 26 of the D.lgs 49/2014
"Implementation of directive 2012/19/EU on
waste electrical and electronic devices
(WEEE)".
The label showing the crossed mobile garbage container
on the product points out that the product must not be
disposed of through the conventional procedure of
disposal of the domestic waste.
To avoid possible damage to the environment and for
improved human health, the product has to be separated
from the other domestic waste and delivered to the
designated collection point for the re-cycling of electric
and electronic waste
The diversified collection and the recycling of rejected
instruments will serve to preserve the natural resources
and to safeguard the environment and the health of the
people .The unauthorized disposal of the product will be
prohibited according to the local news.
For greater details on the available collection centres
please contact the competent local authority or the retailer
of the product.
Proceed as for the storage operation, without doing the
operations of cleaning /removal of scales.
This machine has a warranty of one year from the date of
purchase, please keep your invoice as a proof of
purchase
This machine has been carefully manufactured and
properly tested before delivery. In those cases advised in
the warranty, call the service centre.
- 14 -
220V/230V 60Hz.
230V 50Hz
220V 60Hz
Exemple
Shirt finishers
A
110228
08301/A
Vacuum unit
1
DISPOSAL
WARRANTY
an
Advertisement
Table of Contents
