GE AF-650 GP Programming Manual page 140
General purpose drive
Hide thumbs
Also See for AF-650 GP:
- Quick manual (256 pages) ,
- Programming manual (215 pages) ,
- Design manual (212 pages)
Table of Contents
Advertisement
Parameter Descriptions
LC-10 Comparator Operand
Option:
Function:
[70]
Out of speed
The speed is outside the range set in
range
parameter H-72 Warning Speed Low and
parameter H-73 Warning Speed High.
[71]
Below speed
The output speed is lower than the value
low
in parameter H-72 Warning Speed Low.
[72]
Above speed
The output speed is higher than the
high
value in parameter H-73 Warning Speed
High.
[75]
Out of feedback
The feedback is outside the range set in
range
parameter H-76 Warning Feedback Low
and parameter H-77 Warning Feedback
High.
[76]
Below feedback
The feedback is lower than the limit set
low
in parameter H-76 Warning Feedback Low.
[77]
Above feedback
The feedback exceeds the limit set in
high
parameter H-77 Warning Feedback High.
[80]
Thermal
This operand becomes true when the
warning
frequency converter detects any thermal
warning, for instance when the
temperature exceeds the limit in the
motor, the frequency converter, the
brake resistor, or thermistor.
[82]
Mains out of
The mains voltage is outside the
range
specified voltage range.
[85]
Warning
If a warning is triggered, this operand
gets the warning number.
[86]
Alarm (trip)
A trip alarm is active.
[87]
Alarm (trip lock) A trip lock alarm is active.
[90]
Bus OK
Active communication (no timeout) via
the serial communication port.
[91]
Torque limit &
If the frequency converter has received a
stop
stop signal and is at the torque limit, the
signal is logic 0.
[92]
Brake fault
The brake IGBT is short-circuited.
(IGBT)
[93]
Mech. brake
The mechanical brake is active.
control
[94]
Safe stop active
[100] Comparator 0
The result of comparator 0.
[101] Comparator 1
The result of comparator 1.
[102] Comparator 2
The result of comparator 2.
[103] Comparator 3
The result of comparator 3.
[104] Comparator 4
The result of comparator 4.
[105] Comparator 5
The result of comparator 5.
[110] Logic rule 0
The result of logic rule 0.
[111] Logic rule 1
The result of logic rule 1.
DET-618D
AF-650 GP™ Programming Guide
LC-10 Comparator Operand
Option:
[112] Logic rule 2
[113] Logic rule 3
[114] Logic rule 4
[115] Logic rule 5
[120] Logic Controller
Time-out 0
[121] Logic Controller
Time-out 1
[122] Logic Controller
Time-out 2
[123] Logic Controller
Time-out 3
[124] Logic Controller
Time-out 4
[125] Logic Controller
Time-out 5
[126] Logic Controller
Time-out 6
[127] Logic Controller
Time-out 7
[130] Digital input
DI18
[131] Digital input
DI19
[132] Digital input
DI27
[133] Digital input
DI29
[134] Digital input
DI32
[135] Digital input
DI33
[150] Logic Controller
digital output A
[151] Logic Controller
digital output B
[152] Logic Controller
digital output C
[153] Logic Controller
digital output D
[154] Logic Controller
digital output E
[155] Logic Controller
digital output F
[160] Relay 1
[161] Relay 2
[166] Relay 7
[167] Relay 8
[168] Relay 9
[180] Local referecnce
active
02/2016 All rights reserved.
Function:
The result of logic rule 2.
The result of logic rule 3.
The result of logic rule 4.
The result of logic rule 5.
The result of LC timer 0.
The result of LC timer 1.
The result of LC timer 2.
The result of LC timer 3.
The result of LC timer 4.
The result of LC timer 5.
The result of LC timer 6.
The result of LC timer 7.
Digital input 18 (high=true).
Digital input 19 (high=true).
Digital input 27 (high=true).
Digital input 29 (high=true).
Digital input 32 (high=true).
Digital input 33 (high=true).
Use the result of the Logic Controller
output A.
Use the result of the LC output B.
Use the result of the LC output C.
Use the result of the LC output D.
Use the result of the LC output E.
Use the result of the LC output F.
Relay 1 is active.
Relay 2 is active.
Active when parameter F-02 Operation
Method is [2] Local or when
3
3
139
- Quick Links:
- H-## High Perf Parameters
Hide quick links:
Advertisement
Table of Contents
