Automatically Naming And Saving To Frame Memory - Sony MVS-6520 User Manual
Multi format switcher system with icp-series control panel
Hide thumbs
Also See for MVS-6520:
- Installation manual (38 pages) ,
- Manual (5 pages) ,
- Startup manual (59 pages)
Table of Contents
Advertisement
2
In the <Key Auto Drop> group, press the name of the
keyer for which you want the key to be deleted
automatically, turning it on.
Automatically Naming and Saving to
Frame Memory
In the Engineering Setup >Switcher >Key/Wipe/FM/CCR
menu (7335), press [FM Auto Store], turning it on.
Selecting the Bank to Make the
Settings
In the following procedures, select the bank to which the
settings apply, then make the settings.
Selecting the key memory mode
In the <Key Memory> group of the Engineering Setup
>Switcher >Key/Wipe/FM/CCR menu (7335), select one
from Full (full mode)/Simple (simple mode)/Off
Memory" (p.
81)).
Selecting the processing order of masks
and borders
In the <Mask/Border Process> group of the Engineering
Setup >Switcher >Key/Wipe/FM/CCR menu (7335),
select one of the following.
Mask >Border: Applies the Mask effect, then applies the
Border effect.
Border >Mask: Applies the Border effect, then applies
the Mask effect.
Selecting the key priority operation mode
In the <Key Priority> group of the Engineering Setup
>Switcher >Key/Wipe/FM/CCR menu (7335), select one
of the following.
Normal: The key priority sequence can be varied freely.
Fix: Fixed at currently set priority sequence.
Setting the operation mode of the key bus
[XPT HOLD] button
In the <Xpt Hold Mode> group of the Engineering Setup
>Switcher >Key/Wipe/FM/CCR menu (7335), select any
of the following. This setting is applied for the attributes of
snapshots as well as the operation mode of the [XPT
HOLD] button.
Key Disable: The [XPT HOLD] button of the key bus
functions not only as a cross-point hold button but also
as a key disable button. When the [XPT HOLD] button
is on, recalling a snapshot or keyframe effect does not
reflect the key settings, including the cross-point
selection information.
Key Dsbl with Status: Same as [Key Disable], and further
disables the reflection of the key on/off status.
Xpt Hold: The [XPT HOLD] button of the key bus
functions as a cross-point hold button. When the [XPT
HOLD] is on, recalling a snapshot or keyframe effect
does not reflect the cross-point selection information.
To change the cross-point hold attribute of a
snapshot
If you select [Key Disable] above, this also applies key
disable to the cross-point hold attribute.
If you select [Key Dsbl with Status], the key disable
function is applied, including the key on/off status.
Notes
This setting is only reflected in the operation of the [XPT
HOLD] button when the [XPT HOLD] button operating
mode is set to [All Bus]. Note that the snapshot cross-point
hold attribute is also valid for settings other than [All Bus].
Setting the operation mode when the
pattern limit is released
(1 "Key
In the <Pattern Limit Transition> group of the Engineering
Setup >Switcher >Key/Wipe/FM/CCR menu (7335),
select either of the following operation modes.
Auto: When the pattern limit is released, the remainder of
the transition is carried out automatically at a special-
purpose transition rate.
Manual: After the pattern limit is released, the transition
waits for the next operation, then executes. Until you
move the fader lever or press [AUTO TRANS], the
transition is not executed.
Applying color correction to AUX bus
signal
Notes
When color correction is applied in the AUX bus, the color
correction that was applied to the input signal is disabled.
Settings Relating to Keys, Wipes, Frame Memory and Color Correction
357
- Quick Links:
- Introduction
- System Configuration
Hide quick links:
Advertisement
Table of Contents
