Netum W3 / M3 / M3S / L3 / L3S / D3500 - Wired usb CCD Scanner Manual

Quick Setup Guide

• USB Wired 1D Plug & Play Barcode Scanner
• CCD Image Scanner
• Supports Windows XP, Win7/8/10, MAC, etc.

Packing list:
Quick Start Setup Guide x1 pc
Barcode scanner x 1 pc
Quick Setup Guide V4.1

V4.1.2C

This is 1D & 2D plug and play model if you use a US keyboard. If you use other type of keyboard, plug the USB cable on your device, setup keyboard language before you use it. (refer to below Keyboard Language Type) after that, the scanner can start to work. If you want to do other configurations, please refer to below programming barcodes.

Barcode Programming

Netum barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.

Keyboard Language

In order to let scanner upload the codes in a correct way, you have to set the keyboard language.

For example
If you use French Keyboard, scan below barcode of "French keyboard" then scanner will upload barcodes according to France keyboard layout. American Keyboard is set by default, if you use a US keyboard you can skip this step.

Scanning Mode

Trigger Mode

Press the button to trigger the reading, release the button to end the reading. Reading success or reading time over a single reading time will end the reading.

013300
Manual Trigger *

Auto Sense Mode

Scanning this bar code will enable the scanner to enter auto sense mode.

02311
Auto Sense On

Important Notes: If you want to shift "Auto sense mode" to "Manual trigger mode"you have to first scan "Auto sense off" and then scan "Manual trigger".

02310
Auto Sense Off

Terminator configuration

The scanner provides a shortcut for setting the terminating character suffix to CR or CRLF and enabling it by scanning the appropriate barcode below.

Reader Beep Tone

014201
Beep Tone ON

014200
Beep Tone OFF

Default Configuration

If you want to cancel all the configuration that you have done to the scanner.

Scan "Factory Restore" and then Scan "USB keyboard" to reset the scanner.

000B0
Factory Restore

000602
USB Keyboard

Common Symbologies

Add-On Code

And EAN-8/EAN-13 Barcode can be augmented with a two-digit or five-digit add-on code to form a new one. In the example below, the part surrounded by blue line is an EAN-8 barcode, while the part circled by red line is add-on code. " Disable Add-on Code" is configured by default.

EAN /UPC Add-On 2 or 5

To enable or disable EAN/UPC add on 2 or 5 digits scan the appropriate barcode below.

00551
Enable add-on 2 digits

00552
Enable add-on 5 digits

00553
Enable add -on 2 or 5 digits

00550
Disable add-on 2 or 5 digits*

Interleaved 2 of 5

Enable/Disable Interleaved 2 of 5
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.

00961*
Enabled Interleaved 2 of 5

00960
Disabled Interleaved 2 of 5

MSI

Enable/Disable MSI
To enable or disable MSI, scan the appropriate bar code below.

01151
Enable MSI

01150
Disable MSI

Plessey

Enable /Disable Plessey
To enable or disable Plessey, scan the appropriate bar code below.

01161*
Enable Plessey

01160
Disable Plessey

Code 32

01951*
Enable Code32

01950
Disable Code32

GS1 DataBar Limited(RSS Limited)

01771
Enable RSS Limited

01770
Disable RSS Limited*

GS1 DataBar Omnidirectional(RSS Omnidirectional)

01671
Enable RSS Omnidirectional

01670
Disable RSS Omnidirectional*

Read 1D Normal Barcode/ Reversal Barcode

00161*
Read 1D Normal Barcode

00160
Read 1D Reversal Barcode

FAQ

Problem: Some barcodes cannot be read.
Solution:

1. Dirty or unclear barcodes might not be read.
2. The possible reason is that setting for some barcode types are not commonly used is off by default. You need to activate a specific barcode type to get it to work. Please contact the supplier that you've purchased it from or you may go to our official website www.netum.net; to download the complete manual and refer to the part of " Symbologies".
3. Clean scanner window.

Problem: Carriage Return/Line Feed settings.
Solution: Please refer to the part of "Terminator configuration".

Question: Is there any barcodes for apply or remove suffix?
Yes, you may go to our official websitewww.netum.net/ to download the complete manual and refer to the part of " prefix and suffix".or turn to customer service for help.

Question: How to solve the messy code problem encountered while using other foreign languages?
The default language is English. Please refer to "USB Country Keyboard Types" to change the language according to your own needs.

Contact Information
Tel.: +0086 20-3222-8813
WhatsApp: +86 136 222 33 974
Email: service@netum.net
Addr.:Room 301, 6th Floor and full 3rd Floor, Building 1, No. 51 Xiangshan
Avenue, Ningxi Street, Zengcheng District, Guangzhou, Guangdong, China/511356

Website: https://www.netum.net/

EU Name: Apex CE Specialists GmbH
Add: Habichtweg 1 41468 Neuss Germany

UK Name: APEX CE SPECIALISTS LIMITED
Add: 89 Princess Street, Manchester, M1 4HT,UK