Advertisement
Includes CodeDodger® Remote Control.
The Included Safe-T-Beam® system MUST be installed to close the door. DO NOT use other brands or types. For use with residential sectional overhead garage doors ONLY.
Homelink® and Car2U® compatible
Need help or have questions?
For answers and assistance, visit www.OverheadDoor.com or call Customer Service at: 1-800-929-3667
To reduce the risk of injury to persons or damage to property, use this opener only with a sectional residential door.
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER
HOMEOWNER: SAVE THIS MANUAL FOR FUTURE REFERENCE
SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
FCC Part 15.21 Statement:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
TRANSMITTER COMPLIANCE STATEMENT
Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture. No warranty is made that they comply with all legal requirements of any other jurisdiction. If transmitters are to be used in another country, the importer must determine compliance with any local laws and regulations which may differ from United States and Canadian requirements prior to use.
Please take a moment to preview this manual. Pay particular attention to all Safety Warnings, Cautions and Information. Remember, your garage door is the largest and heaviest moving object in your home.
DO NOT RETURN PRODUCT TO STORE
If you require assistance or have any questions, a knowledgeable Overhead Door Distributor is just a phone call away at: 1-800-929-3667
Or visit our website at: www.OverheadDoor.com
Before setting up your new garage door opener, please locate and record the model plate on the opener. This information will be necessary should you seek technical support via our website, customer support department or local servicing Overhead Door® distributor.
OVERVIEW OF POTENTIAL HAZARDS
READ THIS SAFETY INFORMATION
Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual. If you have questions or do not understand the information presented, call your nearest trained door system technician or visit our website at www.OverheadDoor.com.
CONVENTIONS USED IN THESE INSTRUCTIONS
The following safety alert symbol and signal words are used throughout this manual to call attention to and identify different levels of hazards and special instructions.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and the word "DANGER", "WARNING", or "CAUTION".
POTENTIAL HAZARD | EFFECT | PREVENTION |
MOVING DOOR | Could result in Serious Injury of Death | Do Not operate unless the doorway is in sight and free of obstructions. Keep people clear of opening while door is moving. Do Not allow children to play with the door opener. Do Not change opener control to momentary contact unless and external reversing means is installed. Do Not operate a door that jambs or one that has a broken spring. |
ELECTRICAL SHOCK | Could cause Serious Injury or Death | Turn off electrical power before removing opener cover. When re placing the cover, make sure wires are not pinched or near moving parts. Opener must be electrically grounded. |
HIGH SPRING TENSION | Could cause Serious Injury or Death | Do Not try to remove, repair or adjust springs or anything to which door spring parts are fastened such as wood block, steel brackets, cables or any other structure or like item. Repairs and adjustments must be made by a trained service representative using proper tools and instructions. |
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH
READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. If you have any questions or do not understand an instruction, call The Overhead Door Corp.
Opener is equipped with grounded electrical plug for your protection, and only fits grounded electrical outlets. DO NOT alter plug in any way! If your have no grounded outlets, have one installed by a licensed electrician. Opener must be properly grounded to prevent personal injury and equipment damage. NEVER USE AN EXTENSION CORD! Check local building codes for any requirement that you must have a permanent hard-wired connection. Permanent hard-wired connections must be performed by a licensed electrician using proper tools and instructions.
Safe-T-Beam® (STB) Non-Contact Reversing System
Puts an invisible beam across the door opening. The door stops and reverses to the full open position if anything passes through the beam. LED indicator lights on the powerhead and on the STBs provide self-diagnostics if an operational problems exists.
Door Detect™ Monitoring System
Monitors the Safe-T-Beam® system to ensure proper functionality and will automatically stop and reverse a closing door if a problem is detected.
Safe-T-Reverse® Contact Reversing System
Automatically stops and reverses a closing door within two seconds of contact with an object.
Manual Emergency Release
Manually releases door from door opener. Used during a power failure or other emergency to allow manual opening and closing of door. DO NOT use emergency release cord to pull door
SmartSet® Electronic Programming
Easily adjust the programming to set limits and program new remotes.
Automatic Lighting System
Single or Dual Bulb lighting system supplies light for safer evening exits and entries. Turn ON when door is activated and automatically turns OFF 4 minutes later.
CodeDodger®
An encryption system that enhances the security of the door opener by continuously changing the access code each time the remote is used. The door opener responds to each new code only once. An access code copied from a working system and tried again, will not control the door opener.
Wall Console
Operates door opener from inside garage. The wall console has an indicator light with: Open/Close, Sure-lock™, and independent light control buttons.
Home Link® and Car2U® compatible. See instructions in this manual, refer to the motor vehicle manual or visit www.OverheadDoor.com for instructions.
Factory Programmed Remote Control
For ease and speed of installation, the remote included with this opener comes from the factory, pre-programmed. No additional steps are required to activate the door using the remote.
Safe-T-Beam® (STB) FUNCTION
NOTE: Before programming the opener, check to make sure there are no objects in the garage door opening.
Now that the garage door opener is installed, follow the steps in this manual to program the opener so that the door opens and closes properly and all remote devices operate correctly. The following steps are a guide to setting opener so it functions properly.
The following steps list the order of programming the opener's functional settings for use.
Term Definitions:
Travel Limits Programmable setting to adjust how far door travels up or down.
Force Control refers to how much power is needed to move (open/close) a particular door and does NOT require programming.
Remote Programming synchronizes remote devices (remote and keypad) with the powerhead.
This section describes the programming functions of the opener. Use the following information to understand the buttons and LED indicators used to program functions.
Powerhead: There are 3 programming buttons and 2 LED lights on the powerhead. Each of the buttons are used to enter and complete the setup programming. The LED lights indicate status or a function change by illuminating ON, OFF, or ON FLASHING.
There are 3 programs:
NOTE: The 3 programming buttons are for programming ONLY. These buttons can NOT be used to operate the opener once the Required Programming section has been successfully completed.
Standing under the opener's powerhead – facing the door – looking up – this is the view you will see of the programming buttons and LEDs.
Enters into and selects programming menus.
Moves door up or down during programming and advance through menus.
NOTE: Each programming step has a 30 second time limit for completion after the function is initiated. After 30 seconds, two LED's will illuminate RED indicating time has expired and the step must be re-started. Restart the step as many times as necessary to complete the programming.
NOTE: Carriage should be locked to opener. Door should rest somewhere between full open and closed. Do not start with door fully open or closed.
The force controls are automatically set when the wall control is used for the first time with garage door opener. The door MUST complete one full cycle, from full open to full close and then, full close to full open, before the settings are automatically recorded.
TO AVOID INJURY OR DAMAGE
Force settings are programmed from the factory to remain within safe parameters. These should not require adjustments. However, certain circumstances may require adjustment. See Maintenance and Adjustments for detailed instructions pertaining to the adjustment of force controls.
NOTE: The limit and Force settings MUST BE COMPLETED before performing the Contact Reverse Test.
If the door stops before contacting the board or if it does not reverse direction to fully open after contact with the board, it may be due to an improperly set DOWN limit. Verify settings by:
Repeat this process as needed until the door passes the Contact Reverse Test. For further help, refer to the "Maintenance and Adjustment" section/Regular Maintenance.
THE REMOTE CONTROLS INCLUDED WITH THIS OPENER HAVE BEEN PROGRAMMED AT THE FACTORY FOR YOUR CONVENIENCE.
NOTE: The following instructions are for remote control transmitters purchased separately in addition to those provided with this opener, but can also be used if any remote(s) may require re-programming.
NOTE: Each programming step has a 30 second time limit for completion after the function is initiated. After 30 seconds, two LED's will illuminate RED indicating time has expired and the step must be re-started. Restart the step as many times as necessary to complete the programming.
NOTE: Do not hold remote too close to the powerhead when programming remote buttons.
NOTE: Each button on each remote must be programmed separately, following these steps.
To program the same remote for other garage door openers, repeat the steps above using one of the other remaining remote buttons.
REPEAT STEPS 1 TO 4 FOR EACH OPENER AND REMOTE
NOTE: It is possible to press the remote button too quickly or lightly. If the LEDs do not go off, press the remote button several more times to achieve confirmation.
BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE DOOR OPENER IS READY TO USE.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of severe injury or death, read and follow all instructions.
SAVE THESE INSTRUCTIONS
Opener is equipped with grounded electrical plug for your protection, and only fits grounded electrical outlets. DO NOT alter plug in any way! If your have no grounded outlets, have one installed by a licensed electrician. Opener must be properly grounded to prevent personal injury and equipment damage. NEVER USE AN EXTENSION CORD! Check local building codes for any requirement that you must have a permanent hard-wired connection. Permanent hard-wired connections must be performed by a licensed electrician using proper tools and instructions.
Use of any other wall control can cause unexpected operation of the door and loss of lighting feature. Locate wall console within sight of the door but far enough from door to prevent contacting it while operating the console. Control must be at least 5 feet above the floor to prevent small children from operating it.
Basic monthly maintenance tasks include:
Press and hold both up and down arrow buttons until round LED turns RED, release buttons. Round BLUE LED will flash 3 times. | ||
LEDs will now display current UP force setting (See chart). | ||
Press either arrow button until desired UP force setting is reached. | See Chart | |
Once setting is chosen, press and release. This will lock the UP force setting. | ||
LEDs will now show current DOWN force setting. (See Chart). | ||
Press either arrow button until desired DOWN force setting is reached. | See Chart | |
Once setting is chosen, press and release. This will lock the DOWN force setting. | ||
The LEDs will now turn BLUE then off. This confirms that both force settings have been set and unit is ready for normal operation. | ||
Repeat "Learn Force Limits and Contact Reverse Test". |
Transmitter (RED LED) and Receiver (GREEN LED)
Single Garage Door
Multiple Garage Doors
NOTE: Direct sunlight creates interference with Safe-T-Beam® Receiver (Green LED). STB modules CAN be positioned further away from the door opening if necessary to avoid sunlight but no further off the wall to maintain alignment with the Transmitter (Red LED) module.
NOTE: Only use Safe-T-Beams® that are included with this opener. DO NOT use other brands or types of photocells on this opener.
ELECTRICAL SHOCK
OPENING COVER MAY CAUSE ELECTRICAL SHOCK
Disconnect power from opener prior to removing cover
Need help or have questions? Call Overhead Door at 1-800-929-3667 or visit: www.OverheadDoor.com
PROBLEM: | WHAT TO DO: |
Opener does NOT operate when wall control is pressed. |
|
Opener runs, but door does not move. |
|
Opener works from wall control, but NOT from remote. |
|
Remote has less than 25 feet operating range or no operation. |
|
Door starts down, then STOPS and goes back up. OR Safe-T-Beam® System malfunction. |
|
Door starts down, then STOPS before it is closed. OR Door will only open. |
|
Door starts up, but STOPS before it is completely open. |
|
Door will only run closed. |
|
Door opener starts for no reason. |
|
Noisy operation. |
|
Door opener runs slow. |
|
Powerhead LED | Possible Problem | Solution | |
Round LED | Long LED | ||
OFF | OFF | Normal operation. | None required. |
No response from unit. | Check power supply. Contact a trained door system professional. | ||
ON/RED/STEADY | ON/RED/STEADY | Limits NOT set properly. | Re-program limits, see pages 8-9. |
ON/RED/FLASHING | ON/RED/FLASHING | Program error. | Unplug unit, wait 5 seconds, plug in. |
Component failure. | Contact a trained door system technician. | ||
ON/BLUE/FLASHING | OFF | Remote NOT programmed. | Program remote. |
ON/PURPLE/FLASHING | OFF | Remote NOT programmed. | Program remote. |
ON/RED/FLASHING | OFF | Safe-T-Beam® physical obstruction. | Remote obstruction, recheck unit. |
Safe-T-Beam® signal interference. | Check alignment of Safe-T-Beam® pair and nearest other Safe-T-Beam® pair. | ||
OFF | ON/RED/FLASHING | Door contact in UP or DOWN travel. | Remove obstruction. |
Door component failure detected. | Check door spring, track, rollers, hinges and fixtures. | ||
OFF | ON/RED/STEADY | Thermal cutout. | DO NOT unplug unit. Wait until LED clears before operating. |
ON/PURPLE/STEADY | ON/PURPLE/STEADY | Component error. | Contact a trained door system technician. |
OFF | ON/BLUE/FLASHING | Door will not open. | Check Sure-Lock™. Sure-Lock™ should be OFF for normal operation. |
ON/PURPLE/FLASHING | ON/PURPLE/FLASHING | Radio receiver error. | Unplug the unit. Wait 5 seconds and plug the unit back in. If problems persist, contact a trained door system technician. |
NOTE: Clearing memory of remotes from the powerhead will clear ALL programmed remotes, wireless keypads and vehicle transmitters. The opener will no longer recognize any signal from any remote device, including a missing remote device.
All remaining (or recovered) remotes, vehicles and wireless keypads MUST be reprogrammed.
NOTE: The garage door opener will operate normally using the wall console.
To deprogram the same remote for other garage door openers, repeat the steps above using one of the other remaining remote buttons.
Tip: Program Keypad before mounting.
Keypad Overview:
Activate keypad by opening battery compartment and pull protective tab. Reinstall compartment door to begin programming.
Program the keypad for the first time* with a Personal Identification Number (PIN). This PIN must be 3 to 8 digits.
Program the keypad with a Personal Identification Number (PIN) as described in step 1. Then follow these additional steps.
PROGRAMMING THE KEYPAD TO MULTIPLE OPENERS (UP TO 3)
PUTTING OPENER INTO PROGRAMMING MODE:
NOTE: The openers LEARN LED will time out in 30 seconds. Programming must be completed within 30 seconds.
If the keypad has already been programmed or at any time the programming should be erased and started from the factory default, follow these steps.
Single Door Operation:
Multi-Door Operation:
NOTE: Keypad will remain active for 15 seconds after a successful entry is made. During this 15 seconds ANY key will operate the opener.
Keypad MUST be mounted within sight of the garage door(s) at least 5 feet above floor and clear of any moving door parts.
If the keypad back-lighting fails to operate, Batteries may require replacement.
Rechargeable batteries are NOT recommended.
Changing an Existing PIN:
Setting a Temporary PIN:
A temporary PIN allows temporary access to the garage by, normally unauthorized, personnel such as repairmen or neighbor.
FCC Part 15.21 Statement:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
Pro rails are 1pc rails.
*Belt version shown here
Item | Description | QTY. |
1 | Head To Rail Bracket (2 for Chain, 1 for Belt) | 1 |
1A | Head To Rail Bracket Belt Guard (Belt only) | 1 |
2 | Tensioner Assembly | 1 |
3 | Pulley Tensioner | 1 |
4 | Chain Bullet Assembly | 1 |
Belt Bullet Assembly | 1 | |
5 | Chain & Bullet Assembly, 7 ft | 1 |
Chain & Bullet Assembly, 8 ft | 1 | |
Chain & Bullet Assembly, 10 ft (292") | 1 | |
Chain & Bullet Assembly, 10 ft (303") | 1 | |
Belt & Bullet Assembly, 7 ft | 1 | |
Belt & Bullet Assembly, 8 ft | 1 | |
Belt & Bullet Assembly, 9 ft (268") | 1 | |
Belt & Bullet Assembly, 9 ft (279") | 1 | |
Belt & Bullet Assembly, 10 ft (292") | 1 | |
Belt & Bullet Assembly, 10 ft (303") | 1 | |
6 | Chain Drive Sprocket Assembly | 1 |
Belt Drive Sprocket Assembly | 1 | |
7 | Carriage Assembly, 7 ft Doors | 1 |
Carriage Assembly, 8 ft Doors | 1 | |
Carriage Assembly, 9, 10 ft Doors | 1 | |
8 | Carriage Release Handle | 1 |
9 | Curved Door Arm | 1 |
10 | Installation Parts Pack (Blue Bag) | 1 |
11 | Mounting Parts Pack (Orange Bag) | 1 |
12 | Hanging Hardware Parts Pack (Green Bag) | 1 |
14 | Release Cord Assembly, 7' (32") | 1 |
Release Cord Assembly, 8' (44") | 1 | |
Release Cord Assembly, 9-14' (116") | 1 | |
NS | Wire Clips, (50 pcs) | 1 |
NS | Rail Extender Kit, 8' Chain (for 7' Retail Rail) | 1 |
NS | 3PC Service Rail, C-Channel Chain Drive Rail | 1 |
NS | 3PC Service Rail, C-Channel Belt Drive Rail | 1 |
Yellow parts bag, Photocells | 1 |
Item # | Description | QTY. |
1 | Powerhead Cover, 1029/1029H | 1 |
Powerhead Cover, 2029/2029H | 1 | |
2 | Light Lens Cover | 1 |
3 | Motor Assembly | 1 |
4 | Light Socket Assembly | 1 |
5 | Transformer, 120V | 1 |
6 | Circuit Board Assembly (1029/1029H) | 1 |
Circuit Board Assembly (2029/2029H) | 1 | |
7 | Power Cord Assembly | 1 |
Power Cord Assembly (1029H/2029H) | 1 | |
8 | Screws, M6-1x12 (3pk) | 1 |
9 | Screws, # 8x5/16 (3pk) | 1 |
NS | Optical Dual Encoder Assembly Replacement Kit | 1 |
NOTE: The following kits will include all necessary harnesses, and/or hardware required for reassembly and detailed assembly instructions.
Motor Assemblies
PCB DC Controllers
Light Sockets
Idler Pulley Assembly
Transformer Assembly
Chain & Belt Kits
Covers
Automatic Garage Door Opener and Garage Door Safety and Maintenance Guide
A garage door is the largest moving object in the home. They are often operated by electric door openers. Proper installation, operation and maintenance and testing of the garage door and automatic opener are necessary to provide safe, trouble-free operation. An improperly adjusted garage door or automatic opener can exert deadly force when the door closes. This could lead to serious injury or death from being hit by a closing garage door or from being trapped under the door.
A few simple precautions can protect our family and friends from potential harm. Please take a few minutes to read the following safety and maintenance tips. Refer to your garage door and opener owner's manual for details specific to your garage door and automatic opener.
Some of the following precautions and warnings are identified with this "Safety and Alert Symbol. " This symbol indicates a potential personal safety hazard that can result in injury or death.
Do not stand or walk under a moving door! Do not let children or adults play "beat the door. " It is dangerous and can result in serious injury or death. Adults should set a good example. Know how to use the emergency release, in case someone is pinned by the door.
Do not let children play with or use the transmitters or remote controls. Always place or store them out of the reach of children.
The pushbutton wall control should be out of the reach of children (at least 5 feet from the floor) and away from all moving parts. Mount and use the button where you can clearly see the moving garage door
Garage door openers are not toys. Careless operation and allowing children to play with or use garage door opener controls can lead to tragic results. Discuss garage door safety with your children. Explain the danger of being trapped under the door.
When using the pushbutton or transmitter, keep the door in sight until it completely stops moving. Teach children never to play under or near an open garage door.
Teach children to keep their hands and fingers clear of section joints, hinges, track, springs and other door parts. Contact with a moving door or its hardware could cause serious injury. These injuries can also happen with garage doors that don't have automatic openers.
Take a few minutes to inspect and test your complete garage door system. Make monthly inspection and testing a part of your regular routine. Safety is everyone's business. Make garage door and garage door opener safety automatic in your home.
Monthly Maintenance Checklist.
Garage Door Opener
Garage Door
Consult owner's manual for additional recommended maintenance for your models of door and manual.
There are routine Safety and Maintenance steps that you should follow once a month. Review your owner's manual for the door opener. If you don't have the owner's manual, look for the opener model number on the back of the power unit and request a manual from the manufacturer
Reversal Test
Make sure your opener has a reversing feature. If a reversing feature is not present, it should be replaced. Garage door openers manufactured after January 1, 1993 are required by federal law to have advanced safety features which comply with the latest UL 325 Standards. Contact your manufacturer or installer for additional information.
Test the Reversing Feature every month.
Force Setting Test
Test the force setting of your garage door opener by holding the bottom of the door as it closes. If the door does not reverse readily, the force may be excessive and need adjusting. See your owner's manual for details on how to make the adjustment. Test the reversing feature after any adjustment.
Additional Safety Devices
Many garage door openers can be equipped with additional safety devices. Consider adding a photo eye or edge sensor as an extra measure of safety to protect against entrapment. Keep in mind that adding more safety devices will not make an old opener meet current UL Standards. Make sure the additional safety devices, such as photo eyes or edge sensors, are properly installed and adjusted (see owner's manual).
Perform routine maintenance steps once a month. Review your owner's manual for the garage door. If you don't have a manual, look for the model number on the back of the door, or check the lock handle, hinges or other hardware for the manufacturer's name and request a manual from the manufacturer.
Visual Inspection
Look at the garage door springs, cables, rollers, pulleys and other door hardware for signs of wear. If you suspect problems, have a qualified person make repairs.
Springs are under high tension. Only qualified persons should adjust them.
Garage door springs, cables, brackets and other hardware attached to the springs, are under very high tension and, if handled improperly, can cause serious injury. Only a qualified professional or a mechanically experienced person carefully following the manufacturer's instructions should adjust them. The torsion springs (the springs above the door) should only be adjusted by a professional. Do not attempt to repair or adjust torsion springs yourself. A restraining cable or other device should be installed on the extension spring (the spring along the side of the door) to help contain the spring if it breaks.
Never remove, adjust or loosen the screws on the bottom brackets of the door. These brackets are connected to the spring by the lift cable and are under extreme tension.
Lubrication
Regularly lubricate the moving parts of the door. However, do not lubricate plastic parts such as plastic rollers and plastic idler bearing. Consult the door owner's manual for the manufacturer's recommendation.
Door Balance
Periodically test the balance of your door.
This important information is provided by the U.S. Consumer Product Safety Commission, the National Safety Council and the Industry Coalition for Automatic Garage Door Opener Safety.
The Distributor of Overhead Door Corporation products, whose name appears below ("Seller") warrants to the original purchaser of the Legacy® 1029 or Legacy® 2029 garage door opener ("Product"), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free from defects in materials and workmanship for the following period(s) of time, measured from the date of purchase:
MOTOR/GEARBOX -
Model 2029 - TEN (10) YEARS
Model 1029 - FIVE (5) YEARS
BELT - FIFTEEN (15) YEARS for Belt Drive Product
or
CHAIN - FIVE (5) YEARS for Chain Drive Product
PARTS AND ACCESSORIES - ONE (1) YEAR
Claims under this warranty must be made promptly after discovery and within the applicable warranty period. To obtain warranty service, you must contact the Seller at the address or phone number listed below or by calling 1-800-929-3667 and, if requested, attempt reasonable troubleshooting measures, as well as provide proof of the date and location of purchase, identification as the original purchaser and a description of the claimed defect.
Overhead Door Corporation
1-800-929-3667
www.OverheadDoor.com
©2017 Overhead Door Corporation, the Ribbon Logo, CodeDodger, Legacy and Safe-T-Beam®, are trademarks of Overhead Door Corporation. All other trademarks are property of their rightful owners. Consistent with our policy of continuing product improvements, we reserve the right to change product specifications without prior notice or obligations. HomeLink is a registered trademark of Gentex Corporation. Car2U is a registered trademark of Lear Corporation.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the Legacy 850 that isn't answered in the manual? Leave your question here.