Page 1
Home Network System Window/Door Sensor KX-HNS101FX Model No. Thank you for purchasing a Panasonic product. This document explains how to install the window/door sensor properly. For details about how to use the system, refer to the User’s Guide (page 17).
Table of Contents Introduction Accessory information ....3 Important Information About this system ......4 For your safety ......4 Important safety instructions ..5 For best performance ....5 Other information .......6 Setup Part names and functions ..8 LED indicator ......8 Setup overview ......8 Inserting the battery ....9 Registering the window/door sensor ........9...
Introduction Accessory information Supplied accessories Accessory item/Part number Quantity Battery Mounting screws (20 mm) Mounting double-sided tapes When replacing the battery, see “Power source” of “Specifications”, page 18 for battery information. 2 screws for the sensor unit and 2 screws for the magnet unit 2 pieces of tape for the sensor unit 1 piece of tape for the magnet unit Other information...
R Keep small parts (magnet unit, protection from property loss. magnet unit cover, screws, etc.) out Panasonic will not be held of the reach of children. There is a responsible in the event that risk of swallowing. In the event they...
Hub location/avoiding noise swallowing. If the battery is The hub and other compatible swallowed, seek medical attention Panasonic devices use radio waves to immediately. communicate with each other. R Remove the battery if it becomes R For maximum coverage and unusable.
Important Information – away from electronic appliances Dispose of used batteries according to such as TVs, radios, personal the instructions. computers, wireless devices, or other phones. Routine care – facing away from radio frequency R Wipe the outer surface of the transmitters, such as external product with a soft moist cloth.
Page 7
Important Information For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. Information on Disposal in other Countries outside the European Union These symbols (A, B) are only valid in the European Union.
Setup Part names and LED indicator functions You can press M N and check the LED indicator to confirm the sensor’s n Sensor unit n Magnet unit status. After confirming the sensor’s status, we recommend turning the LED indicator off by pressing M N again as soon as possible, otherwise battery life may be reduced.
Setup Registration Insert the battery. Required only if the window/door sensor was purchased separately (i.e., not as part of a bundle). Confirm the installation area Read the information in this document to confirm that the desired installation area is suitable to proper operation.
Setup R When registration is complete, R Walls containing aluminium-sheet the hub sounds one long beep. insulation R Walls made of concrete or Note: corrugated iron R To cancel without registering the R Double-pane glass windows sensor, press M N on the hub and R Multiple walls on the sensor again.
Setup Temporary placement Before installing the window/door sensor, temporarily place it in the desired location and confirm that it operates properly by pressing M Important: R Attach the sensor unit to the window frame or door frame, and attach the magnet unit to the window or door.
Page 12
Setup Example 1: Installed on the left side of a window Correct Green “ ” marks point directly at each other and are within 25.4 mm of each other. Result: When you press M N (A), the LED indicator lights in green (B). Incorrect “...
Page 13
Setup Example 2: Installed on the right side of a window Correct Green “ ” marks point directly at each other and are within 25.4 mm of each other. Result: When you press M N (A), the LED indicator lights in green (B). Incorrect “...
Setup Installation Install the window/door sensor in the same position where proper operation was confirmed (page 11). You can install the window/door sensor using screws or double-sided tape, depending on your preference or the material of the installation area. Note: R When installing, make sure the battery is inserted properly and the sensor unit cover is completely closed.
Page 15
Setup Sensor unit: Attach the sensor unit. Screws 86.2 mm Magnet unit: Attach the magnet unit. Screws 24.4 mm Attach the covers. Important: Align the “ ” marks on the sensor unit and the magnet unit so that they point directly at each other and are no more than 25.4 mm apart.
Page 16
Setup Securing with double-sided tape Note: R Make sure the surfaces of the sensor unit, magnet unit, and the installation area are clean and dry before applying double-sided tape. Check that the sensor unit cover and magnet unit cover are attached. Affix double-sided tape to the sensor unit and magnet unit.
Appendix You can configure the window/door sensor to trigger other system Testing the window/ events, such as camera recording, door sensor turning on an electric device (such as a lamp), etc. (Appropriate device You can check the window/door required.) sensor’s LED indicator and test the –...
Appendix www.panasonic.net/pcc/support/tel/ homenetwork/manual/ Specifications R Standards DECT (Digital Enhanced Cordless Telecommunications) R Frequency range 1.88 GHz – 1.90 GHz R RF transmission power Approx. 10 mW (average power per channel) 250 mW (max.) R Power source Lithium battery CR2(CR15H270) (1 ´ 3.0 V, 850 mAh) R Operating conditions -10 °C –...