Panasonic HIT VBHN SJ53 Series General Installation Manual
Photovoltaic module
Hide thumbs
Also See for HIT VBHN SJ53 Series:
- Manual (10 pages) ,
- General installation manual (10 pages)
Table of Contents
Advertisement
Quick Links
General Installation Manual
Photovoltaic Module HIT
VBHNxxxSJ53, KJ01 series
Model No.
VBHN330SJ53, VBHN325SJ53, VBHN320SJ53
VBHN325KJ01, VBHN320KJ01
VBHNxxxSJ53 series
Thank you for choosing Panasonic photovoltaic module HIT
Please read this manual completely before you install or use
TM
HIT
. With proper operation and maintenance, HIT
provide you with clean, renewable solar electricity for many
years. This manual contains important installation, mainte-
nance and safety information. The word "module" as used in
this manual refers to one or more PV modules. Retain this
manual for future reference.
TM
VBHNxxxKJ01 series
TM
.
TM
will
CONTENTS
･GENERAL INFORMATION
･SPECIAL CONDITIONS
"HIT" is a trademark of the Panasonic Group.
Other product and service names listed in this
manual are trademarks or registered trademarks
of respective companies.
2
3
5
6
7
8
9
Advertisement
Table of Contents
Related Manuals for Panasonic HIT VBHN SJ53 Series
Summary of Contents for Panasonic HIT VBHN SJ53 Series
-
Page 1: Table Of Contents
･DISPOSAL OF OLD EQUIPMENT DISCLAIMER OF LIABILITY CUSTOMER SERVICES Thank you for choosing Panasonic photovoltaic module HIT “HIT” is a trademark of the Panasonic Group. Please read this manual completely before you install or use Other product and service names listed in this . -
Page 2: Safety Precautions
vices such as ground fault, fuses, Do not puncture or damage the installed by Panasonic. There are no and disconnects may be required. back sheet of a module. Do not use user serviceable parts within the the PV modules and make a replace- ... -
Page 3: Module Specifications
MODULE SPECIFICATIONS 1000W/m , 25°C cell temperature, determining voltage ratings, con- AM1.5 and solar spectral irradiance ductor capacities, fuse sizes, and Module specifications are shown in according to IEC 60904-3. size of controls connected to the Table 1 and Figure 1. (Electrical module output. - Page 4 Dimensions in mm Back side * The positions of the holes are all symmetrical against the center of the module. Side Front side Section A-A’ Section B-B’ Note) A module is installed using 4 points, symmetrical mounting within setting range (shaded). Setting range parameters are shown in “Mount Locations and Load Resistance”...
-
Page 5: Standards
STANDARDS produce flying brands. heating and array current reduction. JUNCTION BOX AND TERMINALS All modules are equipped with fac- VBHNxxxSJ53 and VBHNxxxKJ01 series tory installed bypass diodes. The comply with the requirements of IE- Modules equipped with one junc- factory installed diodes provide C61215, IEC61730-1, IEC61730-2 and the tion box contain terminals for both... -
Page 6: Installation
Conditions. An installation location with conditions beyond the Operating Condi- tions or with other Special Conditions (see below) should be avoided. Operat- ing Conditions of Panasonic modules are as follows: Figure 4. Fixing of cables 1) The modules should be operated only and connectors in terrestrial applications. -
Page 7: Module Installation
Panasonic recom- mends to install modules at a slope Clearance of 100mm between the Please contact your Panasonic Au- steeper than the water gradient. roof surface and module frame is thorized Representative with ques- required to allow cooling air to cir-... -
Page 8: Wiring
Use copper wire which is insulated Please contact your Panasonic Au- to withstand the maximum possible thorized Representative with ques- system open circuit voltage. For tions regarding other electrical con- applications where wire conduits nections if needed. -
Page 9: Maintenance
© SANYO Electric Co., Ltd. 2018 the hazards of electric shock or inju- may be deteriorated or damaged. SANYO is part of the Panasonic Group and is in charge of the manufacturing process of HIT DISPOSAL OF OLD EQUIPMENT...