Table of Contents
Advertisement
Terminal
Input/Output
Name
+SU
DC Input
P24
DC Output
PP
FP
Pulsed Output
IICC
IICC
CCA
CCA
CC
CC
Terminal Descriptions
Note:
The programmable terminal assignments
may be accessed and changed from their
default settings as mapped on
the Direct Access method: Program
Direct Access Applicable Parameter
Number. See the section titled
Mode Menu Navigation on pg. 40
applicable Direct Access parameter
numbers.
Note:
For further information on terminal
assignments and default setting changes,
see the sections titled
Changes on pg. 29
pg.
44.
Note:
See the section titled
Specifications on pg. 282
ASD conductor and terminal electrical
specifications.
Note:
Throughout the manual descriptions and
examples, the sink mode will be used when
referencing discrete terminal functions.
ST — The default setting for this terminal is the
ST
Standby mode controller. As the default setting, this
terminal must be activated for normal system
operation. The ST terminal is activated by
connecting CC to this terminal (Sink mode). When
deactivated, OFF is displayed on the Frequency
Command screen. This input terminal may be
programmed to any of the functions listed in
on page 252
(see F113).
https://www.toshiba.com/tic/
Table 2. Terminal Board Names and Functions. (Continued)
Function (Default Setting If Programmable)
(see
Terminal Descriptions on pg.
Externally-supplied 24 VDC backup control power (1.1 A max.). An alternative to
the EOI
Battery Backup.
24 VDC (200 mA max.) output.
10.0 VDC (10 mA max.) voltage source for the external
potentiometer.
Output Frequency — Multifunctional programmable output
pulse train of a frequency based on the output frequency
(see
Table 10 on page 255).
—
Return for the V/I input terminal.
—
Return for the RR, RX, P24, and the PP terminals.
Return for the AM, FM, +SU, and the discrete input
—
terminal.
pg. 40
Program
for the
Default Setting
and
Input Terminals on
Cable/Terminal
for the Q9 Plus
Table 9
Installation and Connections
Q9 Plus ASD Install/Op Manual
RES — The default setting for this terminal is
Reset. The RES terminal is activated by connecting
CC to this terminal (Sink mode). A momentary
connection to CC resets the ASD and any fault
indications from the display. Reset is effective when
or via
faulted only. This input terminal may be
programmed to any of the functions listed in
on page 252
(see F114).
F — The default setting for this terminal is Forward
run command. The F terminal is activated by
connecting CC to this terminal (Sink mode). This
input terminal may be programmed to any of the
functions listed in (see F111).
R — The default setting for this terminal is Reverse
run command. The R terminal is activated by
connecting CC to this terminal (Sink mode). This
input terminal may be programmed to any of the
functions listed in
S1 — The default setting for this terminal is Fire
Speed. The function of this input as Fire Speed is to
run the motor at the Preset Speed 15 setting upon
activation. Fire Speed activation overrides the Local
and Remote commands (see
This terminal may be activated by connecting CC to
this terminal (Sink mode) and may be initiated by a
fire alarm signal or fire/smoke sensing device. This
input terminal may be programmed to any of the
functions listed in
S2 — The default setting for this terminal is Preset
Speed Bit 2. The function of this input as Preset
Speed Bit 2, in conjunction with S1, S3, and S4, is
to run the motor at the Preset Speed selection of
the S1 – S4 settings when activated. The terminal is
activated by connecting CC to this terminal (Sink
mode). This input terminal may be programmed to
any of the functions listed in
Circuit Config.
15)
Figure 14. on pg. 18.
Figure 15. on pg. 18.
Figure 17. on pg. 18.
DO NOT
connect to
Earth Gnd
or to each other.
Table 9
Table 9 on page 252
(see F112).
Figure 28. on pg.
Table 9 on page 252
(see F115).
Table 9 on page 252
RES
F
R
S1
34).
S2
15
Advertisement
Table of Contents
