Advertisement
3-1. Setup Menu (BVP-550 series)
3-1-6. System Config Menu
Page
Ver.
Item
PreKnee/
PreKnee1
Zebra
R/G/B
Aperture
White Clip
White Clip
Zebra 1 LEVEL, XXX ([XX])
RANGE
Zebra 2 LEVEL
Z.DISP
Test
VTR/CCU
VTR R-Y
VTR B-Y
CCU Y SAMP
CCU R-Y SYNC XXX ([XX])
CCU B-Y SAMP XXX ([XX])
RGB Offset
Test
CB
IRIS
Level
APL Ratio
(Filter Set)
1 or A
2 or B
3 or C
4 or D
Filter Disk
x) Factory setting is as follows:
OHB-450/450P/451/451P/T450WS/T450WSP
(One filter built-in)
1 or A
3200 K
2 or B
5600 K
3 or C
5600 K
4 or D
5600 K
y) The adjustment value is cleared by turning off and on the power sequentially because it is the temporary setting value for adjustment.
3-16 (E)
Settings
Contents
XXX ([XX])
Adjusts the R, G or B pre-knee 1 level on the VA board.
XXX ([XX])
Adjusts the aperture compensation signal level.
XXX ([XX])
Adjusts the white clip level.
[On], Off
Turns the white clip function on and off.
Sets the center value and range for the zebra 1 signal detection.
XXX ([XX])
Sets the detection value for the zebra 2 signal.
1,2, 1&2
Selects a zebra signal to be displayed on the viewfinder.
1
: Zebra 1 signal
2
: Zebra 2 signal
1&2 : Both zebra 1 and 2 signals are displayed at the same time.
1, 2, [Off]
Selects a test signal to be output in setting each item on the
PreKnee/Zebra page.
1
: Outputs the sawtooth test signal
2
: Outputs the 3-step waveform test signal
Off
: No test signal is output
XXX ([XX])
Adjusts the R-Y color-difference signal level.
XXX ([XX])
Adjusts the B-Y color-difference signal level.
XXX ([XX])
Adjusts the level of the sample pulse to be mixed with the Y signal.
Adjusts the level of the sync pulse to be mixed with the R-Y signal.
Adjusts the level of the sample pulse to be mixed with the B-Y signal.
XXX ([XX])
Adjusts the G signal level.
1, 2, [Off]
Selects a test signal to be output in setting each item on the VTR/
CCU page.
1
: Outputs the sawtooth test signal
2
: Outputs the 3-step waveform test signal
Off
: No test signal is output
On, [Off]
Turns on and off the camera color-bar signal to be output when setting
each item on the VTR/CCU page.
XXX ([XX])
Adjusts the auto-iris level.
XXX ([XX])
Sets the way the iris is automatically adjusted.
_99 (PEAK) ↔ 99 (AVERAGE)
3200 K, 4300 K,
Set when the color-temperature filter is assigned according to a user's
5600 K, 6300 K
requirement
x)
n The filter indication on the VF screen can not display correctly
[AUTO], 1, 2
Set corresponding to the filter disc type built in the OHB
After setting, excute the Refernce File Store of the Reference
File menu without fail
AUTO: Automatically recognizes the type of built-in filter
1:
2:
OHB-455WS/455WSP/550/550P/550WS/550WSP
(Two filters built-in)
3200 K
3200 K
4300 K
6300 K
the selected filter type if this item is improperly set
Recognizes the one filter is built in
Recognizes the two filters are built in
y)
BKP-5090
Advertisement
