Table of Contents
Advertisement
en | 4 8 | User Manual | ADS 325
Freeze Frame
ss03213
Connected to 2007 Jeep Wrangler Unlimited X 3.8L
Automated System Test
DTCs
Mode 2 Freeze Frames
Data Stream Snapshot
Freeze Frame 0 - P0123 - ENGINE
Mode 1
Freeze Frame
Mode 5
Mode 6
1. Select a frame.
ss03214
Connected to 2007 Jeep Wrangler Unlimited X 3.8L
Automated System Test
DTCs
Mode 2 Freeze Frames
Data Stream Snapshot
Freeze Frame Description
Mode 1
Diesel Particulate Filter Bank 1 Delta Pressure
Freeze Frame
Diesel Particulate Filter Bank 2 Delta Pressure
Mode 5
Diesel Particulate Filter Bank 1 Inlet Pressure
Diesel Particulate Filter Bank 2 Inlet Pressure
Mode 6
Mode 2 displays recorded data in the form of a DS snap-
shot by the vehicle's computer when specific DTC are
set and the MIL is illuminated.
Mode 5 (Oxygen sensor tests)
Mode 5 views O2 sensor monitor test results.
ss03215
Connected to 2007 Jeep Wrangler Unlimited X 3.8L
Automated System Test
DTCs
Oxygen Sensor Tests (Mode 5)
Data Stream Snapshot
Description
Mode 1
Bank 1 Sensor 1
Maximum Sensor Voltage For
Freeze Frame
Test Cycle
Lean To Rich Sensor Threshold
Mode 5
Voltage
High Sensor Voltage For Switch
Mode 6
Time Calculation
Mode 5 views O2 sensor monitor test results. Mode 5
displays the average of the O2 sensor monitor test re-
sults measured over a period of time. The parameters of
this measurement vary between manufacturers. It may
be necessary to run the vehicle for a period of time to
allow the O2 sensors to fully warm up and begin operat-
ing.
Note: Mode 5 is not supported on all vehicles.
582819 | REV. A | 07.2018
12:46
Change Vehicle
Home
Clear DTCs
Refresh
Share
Save
12:46
Change Vehicle
Home
Clear DTCs
Refresh
Share
Save
Value
-20.6 psi
-18.1 psi
60.3 psi
78.0 psi
12:46
Change Vehicle
Home
Clear DTCs
Refresh
Share
Save
Min
Value
Max
Units
0.000
0.003
1.275
V
0.000
0.003
1.275
V
0.000
0.003
1.275
V
Mode 6 (Non-continuous monitor tests)
Mode 6 views onboard monitoring test results for non-
continuous monitor systems.
ss03216
Connected to 2007 Jeep Wrangler Unlimited X 3.8L
Automated System Test
DTCs
Non-Continuously Monitored Tests
(Mode 6)
Data Stream Snapshot
ECU: ENGINE
Mode 1
TID 1
TID 1
CID 1
TID 1
Freeze Frame
N/A
MIN
Mode 5
TID 2
TID 2
Mode 6
CID 2
TID 2
Non-Continuous Monitor Tests (Mode 6) are pass/fail
tests, including certain EVAP tests, catalyst, and EGR.
The following information is reported:
•
ECU.
•
TID (test identification) indicates the system
monitor.
•
CID (component identification) indicates the
component tested and its test value.
•
Minimum value, maximum value, and current value
for each non-continuous monitor.
•
Pass or fail test result.
Each vehicle manufacturer assigns a code number to
their system monitors and components. Refer to the
vehicle manufacturers Mode 6 code chart to determine
the failure indicated by the TID and CID. If this chart is
not readily available, run an automated system test (AST)
from the DTC screen and select Mode 6. See Read DTCs
section for more information regarding steps to com-
plete this action. This may provide a more detailed
description of the Mode 6 test information.
Change Vehicle
Home
Clear DTCs
Refresh
Share
Passed
9667.0
25292
N/A
VALUE
MAX
UNITS
Failed
Bosch Automotive Service Solutions Inc
12:47
Save
- Quick Links:
- Printer Setup
Hide quick links:
Advertisement
Table of Contents
