Table of Contents
Advertisement
5
Adjustment > Adjustment at Time of Parts Replacement > Action on replacing the finisher controller PCB
Adjustment at Time of Parts Replacement
Action on replacing the finisher controller PCB
1) Before replacing the finisher controller PCB, output the service mode setting values by
P-PRINT.
(COPIER> FUNCTION> MISC-P>P-PRINT)
2) After replacing the finisher controller PCB, enter the following item.
However, in this case, the counter cannot enter.
NOTE:
Either of AB size (A4/A4R) or INCH size (LTR/LTRR) can adjust the item of the
following service modes.
But be careful because the adjustment of DSW is divided into two adjustment modes
of AB system and INCH system.
•
Adjusting the Stacker Alignment Position (A4)
•
Adjusting the Front Staple Position 45deg (A4)
•
Adjusting the Front Staple Position Less Than 45deg (A4R)
•
Adjusting the Rear Staple Position 45deg (A4)
•
Adjusting the Rear Staple Position Less Than 45deg (A4R)
Item
Service mode
Adjustment
(LV.1)
SORTER > ADJUST > ST-ALG1
(LV.1)
SORTER > ADJUST > STP-F1
(LV.1)
SORTER > ADJUST > STP-F2
(LV.1)
SORTER > ADJUST > STP-R1
(LV.1)
SORTER > ADJUST > STP-R2
(LV.1)
SORTER > ADJUST > SW-UP-RL
(LV.1)
SORTER > ADJUST > SDL-STP
(LV.1)
SORTER > ADJUST > SDL-ALG
(LV.1)
SORTER > ADJUST > PRCS-RET
(LV.1)
SORTER > OPTION > PRCS-SP3
5
Adjustment > Adjustment at Time of Parts Replacement > Action on replacing the finisher controller PCB
Items
Adjusting the Stacker Alignment
Position (A4)
Adjusting the Front Staple Position
45deg (A4)
Adjusting the Front Staple Position
Less Than 45deg (A4R)
Adjusting the Rear Staple Position
45deg (A4)
Adjusting the Rear Staple Position
Less Than 45deg (A4R)
Adjusting the Height of the Swing
Roller
Adjusting the Saddle Staple Position
Adjusting the Saddle Alignment
Position
Adjusting the Processing Tray Return
Amount
Change of Paper Stack Speed for Non-
Buffer Mode
Item
Service mode
Function
(LV.1)
setting 1
SORTER> ADJUST> UP-CL
(LV.1)
SORTER> ADJUST> DW-CL
(LV.1)
SORTER> ADJUST> THC-CL
(LV.1)
SORTER> ADJUST> THC-PUSH
(LV.1)
SORTER> ADJUST> OFST-STC
(LV.1)
SORTER> ADJUST> THN-STC
(LV.1)
SORTER> ADJUST> STP-P-CH
(LV.1)
SORTER> ADJUST> TRY-NIS
(LV.1)
SORTER> ADJUST> TRY-SU
(LV.1)
SORTER> ADJUST> FIN-NIS
(LV.1)
SORTER> ADJUST> 1SHT-SHF
(LV.1)
SORTER> ADJUST> SDL-SWCH
(LV.1)
SORTER> ADJUST> SDL-ALM
(LV.1)
SORTER > OPTION > STCR-DWN
(LV.1)
SORTER > OPTION > BUFF-SW
(LV.1)
SORTER > OPTION > PRCS-SP1
(LV.1)
SORTER > ADJUST > THN-STCL
(LV.1)
SORTER > OPTION > NSRT-STC
(LV.1)
SORTER > OPTION > SWGUP-SW
Function
(LV.1)
setting 2
SORTER > OPTION > BLNK-SW
(LV.1)
SORTER > OPTION > MD-SPRTN
(LV.1)
SORTER > OPTION > THN-TRSW
5-17
Items
Setting the Upward Curl Prevention
Mode
Setting the Downward Curl
Prevention Mode
Setting the Thick Paper Curl
Prevention Mode
Setting the Thick Paper Pushing
Forward Prevention Mode
Setting the Poor Offset Stacking
Prevention Mode
Setting the Poor Stacking of Thin
Paper Prevention Mode
Setting the Staple Stack Position
Change Prevention Mode
Setting the Tray Switching Noise
Reduction Mode
Setting the Tray Switching Speedup
Mode
Setting the Finisher Noise Reduction
Mode
Setting the 1-Sheet Shift Sort Enabled Mode
Setting the Saddle Stacking Capacity
Switching Mode
Setting the Saddle Stack Alarm
Detection Disabled Mode
Set Occasional Misalignment Prevention
Mode
Setting Finisher Buffer Operation Mode
Change of Paper Stack Speed for Buffered
Paper Mode
Poor Large/Thin Paper Stack Prevention
Mode
Poor Non-Sort Delivery Stack Prevention
Mode
ON/OFF of the swing unit escape operation
Set Saddle Finisher fold position margin
Restricted operation at Finisher error
Set narrow width thin paper delvry dest
5-17
- Quick Links:
- Installation
Hide quick links:
Advertisement
Table of Contents
