Huawei SmartAX MA5603T Configuration Manual page 195
Access module
Hide thumbs
Also See for SmartAX MA5603T:
- Hardware description (977 pages) ,
- Hardware description (65 pages)
Table of Contents
Advertisement
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
l
Procedure
Step 1 Configure the upstream VLAN interface for the media stream and the signaling stream.
The VLAN ID is 50, the VLAN type is smart VLAN, and the upstream port is 0/19/0, and the
IP address of the VLAN interface is 10.50.1.10/24.
huawei(config)#vlan 50 smart
huawei(config)#port vlan 50 0/19 0
huawei(config)#interface vlanif 50
huawei(config-if-vlanif50)#ip address 10.50.1.10 24
huawei(config-if-vlanif50)#quit
NOTE
Step 2 Configure the media and signaling IP address pools.
The media and signaling IP addresses are 10.50.1.10/24, and the gateway IP address is 10.50.1.1.
huawei(config)#voip
huawei(config-voip)#ip address media 10.50.1.10 10.50.1.1
huawei(config-voip)#ip address signaling 10.50.1.10
huawei(config-voip)#quit
NOTE
Step 3 Configure a static route to the MGC.
The IP address of the destination network segment of the static route to the MGC is 10.10.1.0/24,
and the gateway IP address is 10.50.1.1.
huawei(config)#ip route-static 10.10.1.0 255.255.255.0 10.50.1.1
Step 4 Add an MG interface.
MG interface 0 that supports the MGCP protocol is added.
huawei(config)#interface mgcp 0
Are you sure to add MG interface?(y/n)[n]:y
Step 5 Configure the attributes of the MG interface.
The IP addresses of the MG interface is 10.50.1.10/24, the MG port ID is 2727, the coding mode
is text (default setting), the transmission mode is UDP (default setting), the MG domain name
is MA5600T/MA5603T/MA5608T.com, the IP address of the primary MGC is 10.10.1.4/24,
and the MGC port ID is 2727.
huawei(config-if-mgcp-0)#if-mgcp attribute mgip 10.50.1.10 mgport 2727 domainName
MA5600T/MA5603T/MA5608T.com mgcip_1 10.10.1.4 mgcport_1 2727
Step 6 Reset the MG interface.
huawei(config-if-mgcp-0)#reset
Are you sure to reset MG interface?(y/n)[n]:y
huawei(config-if-mgcp-0)#quit
Step 7 Save the data.
Issue 01 (2014-04-30)
The current system must use the MGCP protocol.
NOTE
Run the display protocol support command to query the current voice protocol. If the voice protocol
is not MGCP, run the protocol support mgcp command to change it to MGCP.
If the packet transmitted from the upstream port is untagged, run the native-vlan command to configure
the native VLAN of the upstream port to be the same as the VLAN of the upstream port.
When configuring the MG interface attributes, ensure that the media and signaling IP addresses exist in
the corresponding address pools.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1 Commissioning
170
- Quick Links:
- Commissioning Introduction
Hide quick links:
Advertisement
Table of Contents
