Page 1 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/ TRV36E/TRV46E RMT-708 SERVICE MANUAL AEP Model UK Model Russian Model East European Model North European Model CCD-TR415E/TR425E/TR515E/TR713E Ver 1.0 1999.01 CCD-TRV26E/TRV27E/TRV36E/TRV46E E Model CCD-TR315E/TR516E CCD-TRV16E/TRV27EP/TRV46E Photo : CCD-TR713E Hong Kong Model CCD-TR315E/TR516E CCD-TRV16E/TRV46E Australian Model CCD-TR315E/TR516E CCD-TRV16E/TRV46E Chinese Model...
Page 2: Camera Recording
CCD-TR516E : 1 lb 11 oz (780 g) 32°F to 104°F(0°C to 40°C) * Minimum illumination expresses the kilohms (ø 3.5 mm) : Monaural type CCD-TR315E : 1 lb 11 oz (790 g) Storage temperature light level a camcorder requires to CCD-TR415E/TR425E/TR515E : Speaker (TRV series only) -4°F to +140°F(-20°C to +60°C)
Page 3 Table for difference of function Model CCD- CCD- CCD- CCD- CCD- CCD- CCD- CCD- CCD- CCD- Remark TR315E TR415E TR415E TR425E TR425E TR515E TR515E TR516E TR713E TR713E Destination E,HK,AUS, AEP,UK EE,NE,RU AEP,UK EE,NE,RU AEP,UK EE,NE,RU E,HK,AUS, AEP,UK EE,NE,RU CN,JE View finder Color ¬...
Page 4 Supplied accessories 1 RMT-708 Wireless Remote Commander (1) 7 Shoulder strap (1) CCD-TR425E/TR515E/TR516E/TR713E 8 21 pin adaptor (1) CCD-TRV27E/TRV27EP/TRV36E/TRV46E CCD- TR415E/TR425E/TR515E/TR713E 2 AC-L10A/L10B/L10C AC power adaptor CCD- TRV26E/TRV27E/TRV36E TRV46E:AEP,UK,EE,NE,RU 3 NP-F330 Battery pack (1) 9 2 pin conversion adaptor (1) 4 CR2025 Lithium Battery (1) CCD- TR315E:E,HK/TR516E:E,HK CCD- TRV16E:E,HK/TRV27EP/TRV46E:E,HK...
Page 5: To Take Out A Cassette When Not Eject (Force Eject)
SERVICE NOTE 1. POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. Battery switch This following three methods are available to prevent this.
Page 6: Self-Diagnosis Function
SELF-DIAGNOSIS FUNCTION 1. Self-diagnosis Function 2. Self-diagnosis display When problems occur while the unit is operating, the self-diagno- When problems occur while the unit is operating, the counter of the sis function starts working, and displays on the viewfinder or Dis- viewfinder or Display window shows a 4-digit display consisting play window what to do.
Page 7: Self-Diagnosis Code Table
4. Self-diagnosis Code Table Self-diagnosis Code Symptom/State Correction Block Detailed Function Code Remove the cassette, and insert it again after one hour. Condensation. Video head is dirty. Clean with the optional cleaning cassette. Non-standard battery is used. Use the InfoLITHIUM battery. LOAD direction.
Page 8: Table Of Contents
TABLE OF CONTENTS SERVICE NOTE 2. DISASSEMBLY 1. Power Supply During Repairs ..........5 2-1. Removal of Front Panel Block and Video Light Block ..2-1 2. To Take out a Cassette when not Eject (Force Eject) ....5 2-2. Removal of LB-54, VF-119 and VF-120 Boards (Color View Finder Models) ....
Page 9 4. PRINTED WIRING BOARDS AND SCHEMATIC 5. ADJUSTMENTS DIAGRAMS 5-1. Camera Section Adjustments ..........5-1 1-1. Preparations before Adjustment (Camera Section) ..5-1 4-1. Frame Schematic Diagram (1) ........... 4-1 1-1-1. List of Service Tools ..........5-1 • Frame Schematic Diagram (2) ........4-4 1-1-2.
Page 10 6-1-7. Clolor EVF Block Assembly (CCD-TR516E) ..6-7 Switch Check (1) ............. 5-43 6-1-8. B/W EVF Block Assembly Switch Check (2) ............. 5-44 (CCD-TR315E/TR415E/TR425E/TR515E/TR713E Headphone Jack Check ........... 5-44 S and TRV series) ............ 6-8 Input/Output Selection Check ......... 5-44 6-1-9.
Page 11: General
CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E This section is extracted SECTION 1 from instruction manual of GENERAL CCD-TRV16E/TRV27E/TRV46E.
Page 20 1-10...
Page 21 1-11...
Page 22 1-12...
Page 23 1-13...
Page 24 1-14...
Page 25 1-15...
Page 26 1-16...
Page 27 1-17...
Page 28 1-18...
Page 29 1-19...
Page 30 1-20...
Page 31 1-21...
Page 32 1-22...
Page 33 1-23...
Page 34 1-24...
Page 35 1-25E...
Page 36: Disassembly
CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E SECTION 2 DISASSEMBLY The equipment can be removed using the following procedure. VIDEO CAMERA RECORDER 2-1. FRONT PANEL BLOCK 2-2. LB-54/VF-119 & 120 BOARDS 2-5. CASSETTE LID ASSEMBLY (Color view finder models only) VIDEO LIGHT BLOCK 2-3. CRT/VF-99 BOARD...
Page 37: Removal Of Lb-54, Vf-119 And Vf-120 Boards (Color View Finder Models)
VF-120 board VF light interception sheet 2-3. REMOVAL OF VF-99 AND CRT ASSEMBLY (B/W view finder model CCD-TR315E/TR415E/TR425E/TR515E/TR713E and TRV series Tilt-up the EVF block to the direction of arrow A . CRT assembly CRT holder assembly Remove the EVF rear cabinet assembly to the direction of arrow B .
Page 38: Removal Of Cabinet (R) Block
2-4. REMOVAL OF CABINET (R) BLOCK Note : Be sure to that the pin of the Lens assembly is put into the hole of the IR knob when attaching. (TR series) (TRV series) Flat cable (FFC-257) Flat cable (FFC-257) CN911, 45P CN911, 45P Two screws Two screws...
Page 39: Removal Of Cabinet (L) Block
Screw (M2 x 3) Two claws 2-9. REMOVAL OF ZOOM LENS BLOCK AND VL-21/22 BOARD —Video light models— CCD-TR515E/TR516E/TR713E CCD-TRV36E/TRV46E —No video light models— CCD-TR315E/TR415E/TR425E CCD-TRV16E/TRV26E/TRV27E/TRV27EP Screw (M2 x 3) Two screws (M2 x 3) Shoe bracket RP shield assembly...
Page 40: Removal Of Vc-215, Se-80/81, Dd-117 And Pj-90/91 Boards
CN101, 12P PJ-90/91 board Two screws (M2 x 4) 2-11. REMOVAL OF VIEW FINDER BLOCK —Color view finder— —B/W view finder— CCD-TR315E/TR415E/TR425E/TR515E/TR713E and TRV series CCD-TR516E VF flexible retainer sheet VF flexible retainer sheet Tapping screw Tapping screw Tapping screw...
Page 41: Removal Of Tr Cover, Cf-60 Board And Display Panel (Tr Series)
2-12. REMOVAL OF TR COVER, CF-60 BOARD AND DISPLAY PANEL ...(TR series) !∞ Liquid crystal display panel Phase adjustment S024 !¢ LCD holder S015 FP-57 flexible board...(Color EVF type only) CN007, 20P Claw Flat cable (FFC-235)...(B/W EVF type only) !™ CF-60 board CN008, 4P !¡...
Page 42: Service Position
2-14. SERVICE POSITION Preparation : Refer to previous section “DISASSEMBLY”, and con- CPC-7 jig (J-6082-382-A) nect as shown in the figure after each parts has been VC-215 board : CN910, 16P removed. Extension cord 70P (J-6082-439-A) —TR series— DD-117 board : CN931 — VC-215 board : CN915 VC-215 board Screw (M2x3) Control switch block...
Page 43: Circuit Boards Location
2-15. CIRCUIT BOARDS LOCATION LB-54... Color EVF models only (Back light) VF-119... Color EVF models only (Color EVF) VF-120... Color EVF models only (Color EVF) CF-60... TR series only DD-117 (Control) (Power) VL-21... TR515E/TR516E/TR713E VF-99... B/W EVF models only VL-22... TRV36E/TRV46E (B/W EVF) (Video light)
Page 44: Block Diagrams
( TRV SERIES ) T901/T902 TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E STANDARD 8 MODEL : TR315E/TR415E/TR425E/TRV16E/TRV26E/TRV27E/TRV27EP B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/TRV16E/TRV26E/TRV27E/ TRV27EP/TRV36E/TRV46E COLOR EVF MODEL : CCD-TR516E REMORT COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/TRV27E/TRV27EP/TRV36E/ TRV46E 3.1V VIDEO LIGHT MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E 3.1V...
Page 45: Camera/Video 1 Block Diagram
IC001 IC401 0.4Vp-p CAMERA REC TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CAMERA REC CAMERA REC IC001 TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E 2.3Vp-p B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/TRV16E/TRV26E/TRV27E/ 7Vp-p 2.3Vp-p TRV27EP/TRV36E/TRV46E 28.375 MHz COLOR EVF MODEL : CCD-TR516E IC501 4.12 MHz 14.18 MHz Q001...
Page 46: Vtr/Camera Control Block Diagram
( TRV SERIES ) 3.1V 3.1V 1.7Vp-p 20 MHz IC402 3.1V 3Vp-p 13usec 3.1V IC402 TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E COLOR EVF MODEL : CCD-TR516E STEADY SHOT MODEL : CCD-TR713E/TRV46E 3.1V 3Vp-p IC402 3Vp-p IC402 ( TR SERIES ) 3.1V...
Page 47: Servo Block Diagram
CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E 3-4. SERVO BLOCK DIAGRAM 3Vp-p 13usec 3Vp-p IC402 0.76Vp-p 2.8msec 506 kHz IC402 IC801 3.1V 1.2Vp-p 5.6msec IC451 3.1V 3Vp-p 3Vp-p 1.2msec 0.76Vp-p IC402 IC402 507 kHz IC801 3Vp-p 13usec IC402 D 3.1V 3-12 3-13 3-14...
Page 48: Mode Control Block Diagram
2.6Vp-p 32 kHz IC604 52 ( TR SERIES ) ( TRV SERIES ) TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E REMOTE COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/TRV27E/TRV27EP/TRV36E/TRV46E VIDEO LIGHT MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E IR TRANSMITTER MODEL : CCD-TR713E/TRV46E ( VIDEO LIGHT MODEL )
Page 49: Audio Block Diagram
( TRV SERIES ) ( TR SERIES ) 3.1V ( TRV SERIES ) CAMERA REC ( TR SERIES ) TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E 2.9Vp-p TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E IR TRANSMITTER MODEL : CCD-TR713E/TRV46E REMOTE COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/TRV27E/TRV27EP/TRV36E/TRV46E IC301 ( TRV SERIES )
Page 50: B/W Evf Block Diagram B/W Evf Model
3-9. B/W EVF BLOCK DIAGRAM B/W EVF MODEL ( TR SERIES ) T901(TYPE3) T902(TYPE2) ( TRV SERIES ) 2.2Vp-p IC901 1Vp-p IC901 TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/TRV16E/ TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E 3-29 3-30 3-31 3-32...
Page 51: Power Block Diagram
( CCD-TR515E/TR516E/TR713E ) ( CCD-TRV36E/TRV46E ) VIDEO 3.1V TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/TRV16E/TRV26E/TRV27E/ TRV27EP/TRV36E/TRV46E COLOR EVF MODEL : CCD-TR516E STEADY SHOT MODEL : CCD-TR713E/TRV46E IR TRANSMITTER MODEL : CCD-TRV46E/TR713E LASER LINK MODEL : CCD-TR713E/TRV46E...
Page 52: Frame Schematic Diagram (1)
( VIDEO LIGHT MODEL ) TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E ( TR515E/TR516E/TR713E ) TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E STANDARD 8 MODEL : CCD-TR315E/TR415E/TR425E/TRV16E/TRV26E/TRV27E/TRV27EP ( TRV36E/TRV46E ) B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/ TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E COLOR EVF MODEL : CCD-TR516E REMOTE COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/...
Page 53 FRAME SCHEMATIC DIAGRAM (2) (TRV SERIES) TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E STANDARD 8 MODEL : CCD-TR315E/TR415E/TR425E/TRV16E/TRV26E/TRV27E/TRV27EP B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/ TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E COLOR EVF MODEL : CCD-TR516E REMOTE COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/ TRV27E/TRV27EP/TRV36E/TRV46E...
Page 54: Cd-210/211 (Ccd Imager) Board
Kinds of capacitor C406 chracteristics C407 CN401 • Chip transistor TR SERIES:CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E • Constants of resistors, capasitors, ICs and etc with XX indicate IC401 TRV SERIES:CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E tha they are not used. In such cases, the unused circuits may be LASER LINK MODEL:CCD-TR713E/TRV46E L401 indicated.
Page 55 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E VC-215 (CAMERA, Y/C PROCESSOR, IN/OUT, REC/PB HEAD AMP, SERVO/SYSTEM CONTROL, SERVO, AUDIO, IR TRANSMITTER, MODE CONTROL) PRINTED WIRING BOARD VC-215 BOARD – Ref No. VC-215 BOARD: 1,000 series – (SIDE B) VC-215 BOARD (SIDE B) C002...
Page 56 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E VC-215 BOARD (SIDE A) VC-215 BOARD (SIDE A) C001 A-13 C336 C-11 R093 C-13 R529 E-12 C004 A-14 C337 A-11 D002 C-13 R096 C-14 R531 F-12 C005 B-14 C338 C-12 D501 F-13 R098 D-14 R532 E-12...
Page 57 3Vp-p IC501 CAMERA REC 3.2Vp-p 0.14usec TR SERIES:CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E IC502 — TRV SERIES:CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 model:CCD-TR515E/TR516E/TR713E/TRV36E/TR46E STANDARD 8 MODEL:CCD-TR315E/TR415E/TR415E/TR515E/TRV16E/TRV26E/TRV27E/TRV27EP CAMERA REC B/W EVF MODEL:CCD-TR315E/TR415E/TR425E/TR515E/TR713ETRV16E/TRV26E/TRV27E/ TRV27EP/TRV36E/TRV46E COLOR EVF MODEL:CCD-TR516E 1.3Vp-p REMOTE COMMANDER MODEL:CCD-TR425E/TR515E/TR516E/TR713E/TRV36E/TRV46E VIDEO LIGHT MODEL:TR515E/TR516E/TR713E/TRV36E/TRV46E STEADY SHOT MODEL:CCD-TR713E/TRV46E IR TRANSMITTER MODEL:CCD-TR713E/TRV46E LASER LINK MODEL:CCD-TR713E/TRV46E IC502 0.4Vp-p...
Page 58 • Refer to page 4–11 for Printed Wiring Board. MPC17A134VMEL TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E STANDARD 8 MODEL : CCD-TR315E/TR415E/TR425E/TRV16E/TRV26E/TRV27E/TRV27EP B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/ TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E COLOR EVF MODEL : CCD-TR516E REMOTE COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/...
Page 59 CAMERA REC CAMERA REC TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E 0.34Vp-p 3Vp-p TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E STANDARD 8 MODEL : CCD-TR315E/TR415E/TR425E/TRV16E/TRV26E/TRV27E/TRV27EP B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/ IC202 IC202 TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E COLOR EVF MODEL : CCD-TR516E R218,R220,R225,R232,Q213,Q214 (CCD-TR516E/TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E) REMOTE COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/...
Page 60 (2.1Vp-p) IC151 (1.6Vp-p) TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E STANDARD 8 MODEL : CCD-TR315E/TR415E/TR425E/TRV16E/TRV26E/TRV27E/TRV27EP B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/ TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E COLOR EVF MODEL : CCD-TR516E REMOTE COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/ TRV27E/TRV27EP/TRV36E/TRV46E VIDEO LIGHT MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E...
Page 61 CAMERA REC 3Vp-p IC001 TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E STANDARD 8 MODEL : CCD-TR315E/TR415E/TR425E/TRV16E/TRV26E/TRV27E/TRV27EP B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/ TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E COLOR EVF MODEL : CCD-TR516E REMOTE COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/ TRV27E/TRV27EP/TRV36E/TRV46E VIDEO LIGHT MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E...
Page 62 IC402 3Vp-p 1.2msec IC402 3Vp-p 2.8msec TR SERIES:CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E IC402 TRV SERIES:CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 model:CCD-TR515E/TR516E/TR713E/TRV36E/TR46E STANDARD 8 MODEL:CCD-TR315E/TR415E/TR415E/TR515E/TRV16E/TRV26E/TRV27E/TRV27EP B/W EVF MODEL:CCD-TR315E/TR415E/TR425E/TR515E/TR713ETRV16E/TRV26E/TRV27E/ TRV27EP/TRV36E/TRV46E COLOR EVF MODEL:CCD-TR516E 3Vp-p REMOTE COMMANDER MODEL:CCD-TR425E/TR515E/TR516E/TR713E/TRV36E/TRV46E VIDEO LIGHT MODEL:TR515E/TR516E/TR713E/TRV36E/TRV46E STEADY SHOT MODEL:CCD-TR713E/TRV46E IR TRANSMITTER MODEL:CCD-TR713E/TRV46E LASER LINK MODEL:CCD-TR713E/TRV46E IC402...
Page 63 VC-215 BOARD (7/10) CAMERA REC 1.2Vp-p 5.6msec IC451 TR SERIES:CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E 3Vp-p TRV SERIES:CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 model:CCD-TR515E/TR516E/TR713E/TRV36E/TR46E STANDARD 8 MODEL:CCD-TR315E/TR415E/TR415E/TR515E/TRV16E/TRV26E/TRV27E/TRV27EP B/W EVF MODEL:CCD-TR315E/TR415E/TR425E/TR515E/TR713ETRV16E/TRV26E/TRV27E/ IC451 TRV27EP/TRV36E/TRV46E COLOR EVF MODEL:CCD-TR516E REMOTE COMMANDER MODEL:CCD-TR425E/TR515E/TR516E/TR713E/TRV36E/TRV46E VIDEO LIGHT MODEL:TR515E/TR516E/TR713E/TRV36E/TRV46E STEADY SHOT MODEL:CCD-TR713E/TRV46E IR TRANSMITTER MODEL:CCD-TR713E/TRV46E LASER LINK MODEL:CCD-TR713E/TRV46E 3Vp-p 2.8msec...
Page 64 • Refer to page 4–11 for Printed Wiring Board. VC-215 BOARD (8/10) CAMERA REC 2.9Vp-p TR SERIES:CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES:CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 model:CCD-TR515E/TR516E/TR713E/TRV36E/TR46E IC301 STANDARD 8 MODEL:CCD-TR315E/TR415E/TR415E/TR515E/TRV16E/TRV26E/TRV27E/TRV27EP B/W EVF MODEL:CCD-TR315E/TR415E/TR425E/TR515E/TR713ETRV16E/TRV26E/TRV27E/ TRV27EP/TRV36E/TRV46E COLOR EVF MODEL:CCD-TR516E REMOTE COMMANDER MODEL:CCD-TR425E/TR515E/TR516E/TR713E/TRV36E/TRV46E VIDEO LIGHT MODEL:TR515E/TR516E/TR713E/TRV36E/TRV46E 0.4Vp-p STEADY SHOT MODEL:CCD-TR713E/TRV46E...
Page 65 TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E The components identified by TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Hi8 MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E mark ! or dotted line with mark STANDARD 8 MODEL : CCD-TR315E/TR415E/TR425E/TRV16E/TRV26E/TRV27E/TRV27EP ! are critical for safety. B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/ TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E (TR SERIES)
Page 66 (TR SERIES) TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E (TRV SERIES) Hi8 MODEL : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E 1.5Vp-p STANDARD 8 MODEL : CCD-TR315E/TR415E/TR425E/TRV16E/TRV26E/TRV27E/TRV27EP B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/ TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E 20 MHz COLOR EVF MODEL : CCD-TR516E REMOTE COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/...
Page 67 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E SE-80/81 (STEADY SHOT (STEADY SHOT MODEL)) PRINTED WIRING BOARD – Ref No. SE-80 BOARD: 4,000 series, SE-81 BOARD: 9,000 series – SE-80 SE-81BOARD SE-80/81 BOARD (SIDE B) SE-80/81 BOARD (SIDE A) C451 C452 C453 C454 C455 C456 C457...
Page 68 C101 C102 C103 C104 (TR SERIES) C105 C106 C107 (TRV SERIES) C108 C109 C110 C111 CN101 D101 D102 TR SERIES:CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E D103 TRV SERIES:CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E D104 D105 D106 J101 L101 L102 L103 L104 PJ-90/91 BOARD (SIDE A) Q101 Q102 R101 100uH R102...
Page 69 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E MA-345, 346 (MIC, LASER LINK) PRINTED WIRING BOARD – Ref No. MA-345 BOARD: 9,000 series, MA-346 BOARD: 9,000 series – MA-345/346 BOARD (SIDE B) MA-345/346 BOARD (SIDE A) POWER CAMERA LIGHT ON/OFF (PLUG IN POWER) 1-672-462- 11...
Page 70 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E TR SERIES : CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E (TR SERIES ) TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E REMOTE COMMANDER MODEL : CCD-TR425E/TR515E/TR516E/TR713E/ (TRV SERIES) TRV27E/TRV27EP/TRV36E/TRV46E IR TRANSMITTER MODEL : CCD-TR713E/TRV46E LASER LINK MODEL : CCD-TR713E/TRV46E R309, S301 (VIDEO LIGHT MODEL) : CCD-TR515E/TR516E/TR713E/TRV36E/TRV46E...
Page 71 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E CF-60 (CONTROL (TR Series)) PRINTED WIRING BOARD – Ref No. CF-60 BOARD: 4,000 series – CF-60 BOARD (SIDE B) CF-60 BOARD (SIDE A) CF-61 BOARD BH001 C001 BACK LIGHT TITLE PICTURE EFECT C002 CN001 CN002 CN005 CN006 CN007...
Page 72 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E (TR SERIES) Q001(CCD- TR315E/TR415E/TR425E/TR515E/TR713E) TR SERIES:CCD- TR315E/TR415E/TR425E/TR515E/TR516E/TR713E) IR TRANSMITTER MODEL:CCD-TR713E/TRV46E BZ002(TR315E/TR516E) CN008(CCD- TR315E/TR415E/TR425E/TR515E/TR713E) CN007(CCD- TR516E) 4-69 4-70 4-71 CONTROL CF-60 (TR Series)
Page 73 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E (TRV SERIES) TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E IR TRANSMITTER MODEL : CCD-TR713E/TRV46E CONTROL 4-72 4-73 4-74 CF-61 (TRV Series)
Page 74 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E CF-61 (CONTROL) (TRV Series) PRINTED WIRING BOARD – Ref No. CF-61 BOARD: 9,000 series – CF-61 BOARD (SIDE B) CF-61 BOARD (SIDE A) CF-61 BOARD BH001 COUNTER DATE TIME RESET BACK C001 LIGHT C002 CN001 CN002...
Page 75 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E PD-107 (RGB DECODER, LCD DRIVE, BACK LIGHT, LCD (TRV Series)) PRINTED WIRING BOARD – Ref No. PD-107 BOARD: 10,000 series – PD-107 BOARD C5501 B-10 FB5502 R5608 C-10 R5695 R5696 D-10 C5502 B-10 FB5503 R5610 B-10 PD-107 BOARD (SIDE B)
Page 76 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E PD-107 BOARD (1/4) CAMERA REC TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E (TRV SERIES) 0.44Vp-p IC5502 0.2Vp-p IC5502 0.2Vp-p IC5502 0.7Vp-p IC5502 3Vp-p IC5502 3.6Vp-p IC5502 3.6Vp-p IC5502 3.6Vp-p IC5502 4-83 4-84 4-85 RGB DECODER PD-107 (1/4) (TRV Series)
Page 77 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E • For schematic diagrams. • Refer to page 4–79 for Printed Wiring Board. PD-107 BOARD (2/4) CAMERA REC 3Vp-p (TRV SERIES) IC5601 3Vp-p IC5601 3.4Vp-p IC5601 3.2Vp-p IC5601 3Vp-p IC5601 MODE1 MCLK HCNT 3Vp-p SRTL SRTR IC5601 CM7017L3-T4...
Page 78 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E • For schematic diagrams. • For schematic diagrams. • Refer to page 4–79 for Printed Wiring Board. • Refer to page 4–79 for Printed Wiring Board. (TRV SERIES) TRV SERIES:CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E (TRV SERIES) TRV SERIES : CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E PD-107 BOARD (4/4) CAMERA REC 2.9Vp-p...
Page 79: B/W Evf (B/W Evf Model)) Board
VF-99 (B/W EVF (B/W EVF MODEL)) PRINTED WIRING BOARD – Ref No. VF-99 BOARD: 10,000 series – VF-99 BOARD (SIDE B) VF-99 BOARD (SIDE A) VF-99 BOARD (TYPE 2/TYPE 3) (TYPE 2) B/W EVF MODEL : CCD-TR315E/TR415E/TR425E/TR515E/TR713E/ C901 R919 TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E C902 R920 C903 R921...
Page 80 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E VF-119 (COLOR EVF (COLOR EVF MODEL)) PRINTED WIRING BOARD VF-119 BOARD – Ref No. VF-119 BOARD: 10,000 series – CAMERA REC VF-119 BOARD (SIDE B) VF-119 BOARD (SIDE A) 3Vp-p IC5401 COLOR EVF MODEL:CCD-TR516E 7.2Vp-p IC5401 7.5Vp-p IC5401 7.6Vp-p...
Page 81 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E VF-120 BOARD CAMERA REC 2.4Vp-p IC5301 12Vp-p IC5301 COLOR EVF MODEL:CCD-TR516E 4-99 4-100 4-101 4-102 COLOR EVF, BACK LIGHT VF-120 (COLOR EVF MODEL), LB-54...
Page 82 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E VF-120 (COLOR EVF), LB-54 (BACK LIGHT) (COLOR EVF MODEL) PRINTED WIRING BOARDS – Ref No. VF-120 BOARD: 10,000 series, LB-54 BOARD: 10,000 series – VF-120 BOARD (SIDE B) VF-120 BOARD (SIDE A) LB-54 BOARD (SIDE B)
Page 83 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E DD-117 (POWER) PRINTED WIRING BOARD – Ref No. DD-117 BOARD: 2,000 series – DD-117 BOARD (SIDE B) DD-117 BOARD (SIDE A) DD-117 BOARD L801 R822 C801 C802 L802 R824 C803 L803 R825 C804 L804 R826 C805 L805 R827...
Page 84 IC801 R877(CCD-TR315E/TR415E/TR425E/TR515E/TR713E) (TRV SERIES) 0.76Vp-p (CCD-TR516E) 506 kHz (TRV SERIES) IC801 (TRV SERIES) D3.1V RN1104F(TPL3) (CCD-TR516E) (CCD-TR516E) (TRV SERIES) 01ZA8.2(TPL3) (TRV SERIES) (TRV SERIES) (TR SERIES) (TRV SERIES) TR SERIES:CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E TRV SERIES:CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E (TRV SERIES) 4-109 4-110 4-111 4-112E POWER DD-117...
Page 85: Adjustments
CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E SECTION 5 ADJUSTMENTS Refer to page 3 as Table for distinction functions of models and classification 5-1. CAMERA SECTION ADJUSTMENTS 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope •...
Page 86: Adjusting Items When Repacing Main Parts
1-1-2. Adjusting items when replacing main parts When replacing main parts, adjust the items indicated by r in the following table. Replacing parts Adjustment Adjusting item Section Initialization of D, E, F page data Camera G-CAM flip adj. Camera HALL adj. Camera Flange back adj.
Page 87: Preparations
1-1-3. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. 1) Connect the equipment for adjustments according to Fig. 5-1-3, 2) By setting the “Forced Camera Power ON mode”, the camera power can be turned ON even if the front panel block (MA-345/ Pattern box...
Page 88 TR SERIES Color monitor Vector scope Terminated at 75 Ω Lens block CD-210 board Regulaterd power supply CN401 (8.4 ± 0.1 Vdc) Battery terminal (Note 1) Extension cable(16P) (J-6082-357-A) Adjusting VL-21 board remote CN151 commander Battery switch VIDEO terminal LANC CN935 CN909 terminal...
Page 89 TRV SERIES Color monitor Vector scope Terminated at 75 Ω Lens block CD-211 board Regulaterd power supply CN401 (8.4 ± 0.1 Vdc) Battery terminal (Note 2) Extension cable(16P) (J-6082-357-A) Adjusting VL-22 board remote CN151 commander Battery switch VIDEO terminal LANC CN935 jack CN909...
Page 90: Precautions
1-1-4. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. 1. POWER switch (MA-345/346 board) ....CAMERA 7. FOCUS switch (MF-8500) ........MANUAL 2. NIGHT SHOT switch (Lens Block) ........ OFF 8.
Page 91: Adjusting Remote Commander
1-1-5. Adjusting Remote Commander • Changing the address The adjusting remote commander is used for changing the calcula- The address increases when the FF ()) button is pressed, tion coefficient in signal processing, EVR data, etc. The adjusting and decreases when the REW (0) button is pressed. There remote commander performs bi-directional communication with the are altogether 256 addresses, from 00 to FF.
Page 92: Data Processing
1-1-6. Data Processing The calculation of the DDS display and the adjusting remote calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Table 5-1-2. indicates the hexadecimal commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items.
Page 93: Initialization Of D, E, F
1-2. INITIALIZATION OF D, E, F PAGE DATA 2. Modification of D, E, F Page Data If the D, E, F page data has been initialized, change the data of the 1. Initializing the D,E,F Page Data “Fixed data-2” address shown in the following tables by manual Note 1: If “Initializing the D, E, F Page Data”...
Page 94 3. D Page Table Note1 : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Address Initial Remark Address Initial Remark Value Value 00 to 0F...
Page 95 BPF f0 adj. cording to the model. Fixed data-1 Hi8 model :CCD-TR515E/TR516E/TR713E Y OUT level adj. CCD-TRV36E/TRV46E AFC f0 adj. Standard8 model : CCD-TR315E/TR415E/TR425E C OUT level adj. CCD-TRV16E/TRV26E/TRV27E/TRV27EP Fixed data-1 Filter f0 adj. Address Initial Remark RP filter f0 adj.
Page 96 Address Initial Remark Address Initial Remark Value Value Fixed data-1 Fixed data-2 Fixed data-1: CCD-TR315E/TR415E/TR425E/TR515E/TR516E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E Fixed data-2: CCD-TR713E, CCD-TRV46E Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1...
Page 97 Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Note 2: See “1-4. COLOR ELECTRONIC VIEWFINDER SYS- TEM ADJUSTMENT”. Note 3: See “1-5. LCD SYSTEM ADJUSTMENT”. Note 4: TR series: CCD-TR315E/TR415E/TR425E/TR515E/ TR516E/TR713E TRV series: CCD-TRV16E/TRV26E/TRV27E/TRV27EP/ Fixed data-2 TRV36E/TRV46E...
Page 98 Address Initial Remark Address Initial Remark Value Value Note 3 Contrast adj. (LCD) TR series:Fixed data-1/TRV series:Fixed data-2 Note 3 D range adj. (LCD) Fixed data-1 Note 3 V-COM level adj. (LCD) Fixed data-2 Note 3 VCO adj. (LCD) Fixed data-1 Note 3 V-COM adj.
Page 99: Camera System Adjustments
1-3. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, Check that the specified value of “28MHz Origin Oscillation Adjustment”, “Y OUT level Adjustment” and “C OUT level Adjustment” of “VIDEO SYSTEM ADJUSTMENT” are satisfied. 1. G-CAM flip Adjustment Set the color reproduction conditions to optimum. Subject Color bar chart standard picture frame Measurement Point...
Page 100: Hall Adjustment
2. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain and offset. Subject Not required Measurement Point DDS display data of LCD or TV monitor (Note 3) Measuring Instrument Adjustment Page Adjustment Address 2F, 30 Specified Value 7E to 82 during IRIS OPEN (Note 1) 13 to 17 during IRIS CLOSE (Note 2)
Page 101: Flange Back Adjustment
3. Flange Back Adjustment 3-2. Flange Back Adjustment (2) The inner focus lens flange back adjustment is carried out auto- Perform this adjustment after performing “Flange Back Adjustment matically. In whichever case, the focus will be deviated during auto (1)”. focusing/manual focusing.
Page 102: Flange Back Check
4. Flange Back Check 5. Picture Frame Setting Subject Siemens star chart Subject Color bar chart standard picture frame (2.0 m from the front of the lens) (1.5m from the front of the lens) (Luminance: approx. 200 lux) Measurement Point Video output terminal Measurement Point Check operation on TV monitor...
Page 103: Color Reproduction Adjustment
6. Color Reproduction Adjustment Adjust the color Separation matrix coefficient so that proper color reproduction is produced. Subject Color bar chart standard picture frame Burst position Measurement Point Video output terminal Measuring Instrument Vectorscope Adjustment Page Adjustment Address 34, 36, F5, F6 Specified Value All color luminance points should settle within each color reproduction frame.
Page 104: Iris In/Out Adjustment
7. IRIS IN/OUT Adjustment 8. MAX GAIN Adjustment For the unit to judge if the white balance is indoors or outdoors in Setting the minimum illumination. auto white balance operations, measure the light level and write it If it is not consistent, the image level required for taking subjects in in the EEPROM.
Page 105: Auto White Balance Standard Data Input
9. Auto White Balance Standard Data Input 10. Auto White Balance Adjustment Adjust to the proper auto white balance output data. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color bar standard picture frame) be poor.
Page 106: White Balance Check
11. White Balance Check Subject Clear chart (Color bar standard picture frame) Filter Filter C14 for color temperature correction ND filter 1.0 and 0.3 2 mm Measurement Point video output terminal Measuring Instrument Vectorscope Specified Value Fig. 5-1-11. A to C Switch setting: 1) NIGHT SHOT switch ............
Page 107: Angular Velocity Sensor Sensitivity Check (Ccd-Tr713E/Trv46E)
12. Angular Velocity Sensor Sensitivity Check (CCD-TR713E, CCD-TRV46E) • This adjustment is performed only when replacing the angular velocity sensor. Although this adjustment need not be performed when the circuit is damaged, etc., check the operations. • Note down the sensitivity displayed on the angular velocity sensor of the repair parts.
Page 108: Color Electronic Viewfinder System Adjustments (Ccd-Tr516E)
1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM 1. EVF Initial Data Input ADJUSTMENT Mode VTR stop (CCD-TR516E) Signal No signal Note 1: The back light (fluorescent tube) is driven by a high volt- Adjustment Page age AC power supply. Therefore, do not touch the back Adjusting Address C2 to CD light holder to avoid electrical shock.
Page 109: Vco Adjustment (Vf-119 Board)
2. VCO Adjustment (VF-119 board) 3. Bright Adjustment (VF-119 board) Set the VCO free-run frequency. If deviated, the EVF screen will be Set the level of the VIDEO signal for driving the LCD to the speci- blurred. fied value. If deviated, the screen image will be blackish or satu- rated (whitish).
Page 110: Contrast Adjustment (Vf-119 Board)
4. Contrast Adjustment (VF-119 board) 5. Backlight Consumption Current Adjustment (VF-120 Set the level of the VIDEO signal for driving the LCD to the speci- board) fied value. If deviated, the screen image will be blackish or satu- Set the backlight luminance and color temperature. rated (whitish).
Page 111: Monochrome Electronic Viewfinder System Adjustments (B/W Evf Model)
1-5. MONOCHROME ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENTS Note: CCD- TR315E/TR415E/TR425E/TR515E/TR713E CCD- TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/ TRV46E 1-5-2. Centering Adjustment 1-5-1. Horizontal Slant Check Mode Playback Mode Playback Signal Alighment tape : Signal Alighment tape : For checking operations For checking operations (WR5-5CSP) (WR5-5CSP) Monoscope section Monoscope section Specified Value ±...
Page 112: Aberration Adjustment
1-5-4. Aberration Adjustment 1-5-5. Horizontal Amplitude Adjustment (VF-99 board) Mode VTR stop Signal Dot pattern Mode Playback Specified Value b1 2 • a1 Signal Alighment tape : b2 0.8 • a2 For checking operations (WR5-5CSP) Adjusting method: Monoscope section 1) Adjust the aberration adjustment ring so that the tracing of the Adjusting Element C909 (SOL901) dot satisfies the specified value.
Page 113: Vertical Amplitude Adjustment (Vf-99 Board)
1-5-6. Vertical Amplitude Adjustment (VF-99 board) 1-5-7. Brightness Adjustments (VF-99 board) Mode Playback Mode Playback Signal Alighment tape : Signal Alighment tape : For checking operations For checking operations (WR5-5CSP) (WR5-5CSP) Monoscope section Monoscope section Adjusting Element RV903 Specified Value RV904 Specified Value 10 ±...
Page 114: Lcd System Adjustment (Trv Series)
1-6. LCD SYSTEM ADJUSTMENT (TRV SERIES) 1. LCD Initial Data Input Note1: The back light (fluorescent tube) is driven by a high volt- Mode VTR stop age AC power supply. Therefore, do not touch the back Signal Arbitrary light holder to avoid electrical shock. Adjustment Page Note2: When replacing the LCD unit, be careful to prevent dam- Adjustment Address...
Page 115: Vco Adjustment (Pd-107 Board)
2. VCO Adjustment (PD-107 board) 3. D range Adjustment (PD-107 board) Set the VCO freerun frequency. If deviated, the LCD screen will be Set the D range of the RGB decoder used to drive the LCD to the blurred. specified value. If deviated, the LCD screen will become blackish or saturated (whitish).
Page 116: Bright Adjustment (Pd-107 Board)
4. Bright Adjustment (PD-107 board) 5. Contrast Adjustment (PD-107 board) Set the level of the VIDEO signal for driving the LCD to the speci- Set the level of the VIDEO signal for driving the LCD to the speci- fied value. If deviated, the screen image will be blackish or satu- fied value.
Page 117: V-Com Level Adjustment (Pd-107 Board)
6. V-COM Level Adjustment (PD-107 board) 7. Color Adjustment (PD-107 board) Set the common electrode drive signal level of LCD to the specified Set the color saturation to the standard value. If deviated, the color value. will be to dark or light. Mode VTR stop Mode...
Page 118: V-Com Adjustment (Pd-107 Board)
8. V-COM Adjustment (PD-107 board) 9. White Balance Adjustment (PD-107 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and con- Mode VTR stop...
Page 119: Mechanical Section Adjustment
5-2. MECHANICAL SECTION ADJUSTMENT 6) Connect the oscilloscope. Channel 1: Pin 6 of CN910 of VC-215 board External trigger: Pin !¡ of CN910 of VC-215 board Mechanism Parts Adjustments Connect the oscilloscope via the CPC-7 jig For details on the adjustments and checks of mechanical section (J-6082-382-A).
Page 120: Video Section Adjustment
5-3. VIDEO SECTION ADJUSTMENTS When performing adjustments, refer to the layout diagrams for adjustment related parts beginning from page 5-60. 3-1. PREPARATIONS BEFORE ADJUSTMENT The following adjusting instruments are used for adjusting the video section. 3-1-1. Equipments to be Used 1) TV monitor 2) Oscilloscope: 2 phenomena, band 30 MHz or wider, with de- lay mode.
Page 121: Precautions On Adjusting
3-1-2. Precautions on Adjusting 3-1-3. Adjusting Connectors 1) The adjustments of this unit are performed in the VTR mode or Some of the adjusting points of the video section are concentrated camera mode. at VC-215 board CN910. Connect the measuring instruments via To set to the VTR mode, set the power switch to “VTR”...
Page 122: Connecting The Equipments
3-1-4. Connecting the Equipments Connect the measuring instruments as shown in Fig. 5-3-2 and perform the adjustments. Connecting the TV Monitor and Regulated Power Supply Battery terminal Main Unit TV monitor Regulated power supply 8.4 ± 0.1Vdc VIDEO Connect when using the camera mode or playing back.
Page 123 Note: Measure using the VIDEO terminal (Terminated at 75 Ω). Fig. 5-3-3. shows the 75% color bar signals recorded on the align- ment tape. Fig. 5-3-3. Color Bar Signals of the Alignment Tape 5-39...
Page 124: Input/Output Level And Impedance
3-1-6. Input/Output Level and Impedance 3-1-8. Service Mode Video output Phono jack, 1 Vp-p, 75Ω, Additional note on adjustment unbalanced, sync negative Note: After the completion of the all adjustments, cancell the ser- Audio output Phono jack, vice mode by either of the following ways. Output: –7.5 dBs, (at load impedance 47 kΩ), impedance less than 2.2 kΩ...
Page 125: Emergency Memory Address
2. Emergency Memory Address 2-1. EMG CODE (Emergency Code) The codes shown in the following table which correspond to errors Page F Address 10 to 1B that occur are recorded in addresses 10, 14, and 18. Address Contents Code Type of Emergency 1st EMG code No error Upper: MSW code when the mechanism starts shifting...
Page 126: Msw Codes
2-2. MSW Codes • The lower parts of the data of addresses 12, 16 and 1A represent the MSW codes (mode switch, mechanism position) when errors occurs. • The upper parts of the data of addresses 12, 16 and 1A represent, when the mechanism position is to be moved, the MSW codes at the start of movement (when moving the loading motor).
Page 127: Bit Value Discrimination
3. Bit value discrimination 4. Switch check (1) Bit values must be discriminated using the display data of the ad- Page 3 Address 43 justing remote commander for the following items. Use the table below to discriminate if the bit value is “1” or “0”. Function When bit value=1 When bit value=0 0 VTR MODE SW...
Page 128: Switch Check (2)
5. Switch check (2) Page 3 Address 60 to 66 Using method: 1) Select page: 3, address: 60 to66. 2) By discriminating the display data, the pressed key can be dis- criminated. Data Address 00 to 0D 0E to 29 2A to 46 47 to 68 69 to 90...
Page 129: Led, Lcd (Display Window) Check
8. LED, LCD (display window) check 9. Record of Use Check Page 3 Address 05 Bit5 Page 3 Address A2 to AA Address Function Remarks Using method: 1) Select page: 3, address: 05, and set the bit value of Bit5 to “1”. 1000th place digit and 2) Check that all LED are lit and all segments of LCD (display 100th place digit of...
Page 130: System Control System Adjustment
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Initialization of D, E, F Page Data If the D, E, F page data is erased due to some reason, perform “1-2. INITIALIZATION OF D, E, F PAGE DATA”, of “5-1. CAMERA SECTION ADJUSTMENT”. 2.
Page 131: Servo System Adjustments
3-3. SERVO SYSTEM ADJUSTMENTS 2. RF Switching Position Adjustment (VC-215 Board) If deviated in this case causes switching noise or jitter on the played 1. CAP FG Offset Adjustment (VC-215 board) back screen. Improve the capstan servo characteristic. If it is not correct. jitters Mode Playback will increase.
Page 132: Video System Adjustments
3-4. VIDEO SYSTEM ADJUSTMENTS 2. AFC f Adjustment (VC-215 board) Adjust the pull-in range of the A/D converted clock generator dur- Video system adjustments must be performed in the following order. ing playback. Mode VTR stop [Adjusting Order] Signal No signal 1.
Page 133: Filter F0 Adjustment (Vc-215 Board)
4. Y OUT Level Adjustment (VC-215 board) 3. Filter f Adjustment (VC-215 board) Set the Y signal output level. Minimize the chroma signal residual components during compos- ite video signal input. Mode VTR stop Signal No signal Mode VTR stop Measurement Point VIDEO terminal (75Ω...
Page 134: C Out Level Adjustment (Vc-215 Board)
5. C OUT Level Adjustment (VC-215 board) 6. RP Filter f Adjustment (VC-215 board) Set the chroma signal output level. Adjust the LPF of the playback RF amplifier. Mode VTR stop Mode VTR stop Signal No signal Signal No signal Pin 9 of CN910 (RF AGC OUT) Measurement Point VIDEO terminal (75Ω...
Page 135: Hi8 Rec Y Current Adjustment (Vc-215 Board) Ccd-Tr515E/Tr516E/Tr713E Ccd-Trv36E/Trv46E
7. Hi8 REC Y Current Adjustment (VC-215 board) 14) Write the following data in page: F, address: 57 to 5A. CCD-TR515E/TR516E/TR713E Address Data CCD-TRV36E/TRV46E Adjust the Y FM signal recording current. Mode VTR recording (SP mode) Signal No signal Pin !º of CN910 (REC RF) Measurement Point Note: After setting each data, be sure to press the PAUSE button Measuring Instrument Oscilloscope...
Page 136: Ccd-Tr315E/Tr415E/Tr425E Ccd-Trv16E/Trv26E/Trv27E/Trv27Ep
8. Standard8 REC Y Current Adjustment (VC-215 board) 14) Write the following data in page: F, address: 57 to 5A. CCD-TR315E/TR415E/TR425E Address Data CCD-TRV16E/TRV26E/TRV27E/TRV27EP Adjust the Y FM signal recording current. Mode VTR recording (SP mode) Signal No signal Pin !º of CN910 (REC RF)
Page 137: Hi8 Rec L Level Adjustment (Vc-215 Board) Ccd-Tr515E/Tr516E/Tr713E Ccd-Trv36E/Trv46E
9. Hi8 REC L Level Adjustment (VC-215 board) 13) Calculate the adjustment data (hexadecimal) from the follow- CCD-TR515E/TR516E/TR713E ing equations (hexadecimal calculation), and input each adjust- CCD-TRV36E/TRV46E ment address. (Refer to Table 5-1-2. Hexadecimal-Decimal Set the recording levels of the REC AFM signal and REC ATF sig- conversion Table.) nal.
Page 138: Standard8 Rec L Level Adjustment (Vc-215 Board)
10. Standard8 REC L Level Adjustment (VC-215 board) 14) Write the following data in page: F, address: 63 to 64. CCD-TR315E/TR415E/TR425E Address Data CCD-TRV16E/TRV26E/TRV27E/TRV27EP Set the recording levels of the REC AFM signal and REC ATF sig- nal. If the level is too low, the audio S/N will deteriorated, tracking will not be stable, or SP/LP will not be discriminated properly.
Page 139: Rec C Current Adjustment (Vc-215 Board)
A = 34.6±1.2mV Standard8 model : A = 30.0±1.1mV Note 1: Hi8 model: CCD- TR515E/TR516E/TR713E CCD-TRV36E/TRV46E Standard8 model: CCD-TR315E/TR415E/TR425E CCD-TRV16E/TRV26E/TRV27E/ TRV27EP Connection: 1) Remove C085 (0.01µF, Pin !§ of IC202). Note: After completing “REC L Level Adjustment” and “REC C Current Adjustment”, replace C085 with new parts (1-162-...
Page 140: Ir Transmitter Adjustments (Ccd-Tr713E/Trv46E)
3-5. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (VC-215 board) (CCD-TR713E/TRV46E) Mode Camera standby Subject Arbitrary Adjust using a IR receiver jig (J-6082-383-A). Measurement Point VIDEO OUT terminal of IR receiver jig (Terminated at 75Ω) Switch setting: Measuring Instrument Oscilloscope LASER LINK ....
Page 141: Ir Audio Deviation Adjustment (Vc-215 Board)
3. IR Audio Deviation Adjustment (VC-215 board) Mode VTR recording Signal Audio signal : 400Hz, –7.5dBs : AUDIO terminal Video signal : Color bar signal : VIDEO terminal Measurement Point AUDIO terminal of IR receiver jig ( Terminated at 47kΩ) Measuring Instrument Audio level meter Adjustment Page...
Page 142: Audio System Adjustment
3-6. AUDIO SYSTEM ADJUSTMENT 1. 1.5 MHz Deviation Adjustment (VC-215 board) Adjust to the optimum audio FM signal distortion. [Connecting the measuring instruments for the audio] If the adjustment is not correct, its playback level will differ from Connect the audio system measuring instruments besides the video that of other units.
Page 143: Arrangement Diagram For Adjustment Parts
3-7. ARRANGEMENT DIAGRAM FOR ADJUSTMENT PARTS VC-215 BOARD (SIDE A) CN909 CN551 CN501 IC604 IC202 CN911 C085 IC001 IC301 VC-215 BOARD (SIDE B) IC501 CN910 IC751 5-59 5-60E...
Page 144: Repair Parts List
CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they are • Abbreviation The components identified by seldom required for routine service. Some delay East European model is abbreviated as EE.
Page 145: Cabinet (L) And Battery Panel Assembly
6-1-2. CABINET (L) AND BATTERY PANEL ASSEMBLY not supplied not supplied not supplied not supplied J901 See page 6-6 not supplied S003 J001 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-962-826-01 SCREW (2 x 4) 3-987-679-01 SHEET METAL (LOWER), STRAP 3-948-339-61 TAPPING 3-975-752-01 LID (BT), CPC...
Page 146: Front Panel Block Assembly
6-1-3. FRONT PANEL BLOCK ASSEMBLY Video light model CCD-TR515E/TR516E/TR713E CCD-TRV36E/TRV46E No video light CCD-TR315E/TR415E/TR425E model CCD-TRV16E/TRV26E/TRV27E/TRV27EP - 3 4 not supplied not supplied not supplied not supplied No video light models LAMP,HALOGEN MIC901 VL901 XB-3D(DC6V/3W) Video light models The components identified by mark ! or dotted line with mark ! are critical for safety.
Page 147: Cabinet (R) Block Assembly (Tr Series)
6-1-4. CABINET (R) BLOCK ASSEMBLY (TR series) not supplied See pages 6-7 to 6-8 Note Sample DIGITAL ZOOM Note About the magnification display section There are two kinds of magnification of Digital zoom only for the AEP model. Please make sure the magnification of your Handycam with reference to the LCD903 Cabinet (R) assembly of...
Page 148: Cabinet (R) Block Assembly (Trv Series)
6-1-5. CABINET (R) BLOCK ASSEMBLY (TRV series) See page 6-8 not supplied not supplied Note SP901 Sample DIGITAL ZOOM See page 6-9 Note About the magnification display section There are two kinds of magnification of Digital zoom only for the AEP model. Please make sure the magnification of your Handycam with reference to the Cabinet (R) assembly of...
Page 149: Main Boards Block Assembly
6-1-6. MAIN BOARDS BLOCK ASSEMBLY Video light model CCD-TR515E/TR516E/TR713E CCD-TR415E/TR425E/TR515E/TR713E CCD-TRV36E/TRV46E No video light CCD-TR315E/TR415E/TR425E CCD-TRV26E/TRV27E/TRV36E model CCD-TRV16E/TRV26E/TRV27E/TRV27EP TRV46E:AEP,UK,EE,NE,RU No video light models See page 6-10 not supplied - 1 1 - 2 1 Video light models SE452 See pages 6-11 to 6-13 SE451 CCD-TR713E &...
Page 150 6-1-7. COLOR EVF BLOCK ASSEMBLY (Color View Finder model CCD-TR516E) Note : As for the model whitch carries a B/W view finder, refer to page 6-8. LCD902 not supplied ND5351 not supplied The components identified by mark ! or dotted line with mark ! are critical for safety.
Page 151: B/W Evf Block Assembly (Ccd-Tr315E/Tr415E/Tr425E/Tr515E/Tr713E S And Trv Series)
6-1-8. B/W EVF BLOCK ASSEMBLY (B/W View Finder models CCD-TR315E/TR415E/TR425E/TR515E/TR713E & TRV series) Note : As for the model whitch carries a color view finder, refer to page 6-7. V901 The components identified by mark ! or dotted line with mark ! are critical for safety.
Page 152: Lcd Block Assembly (Trv Series)
6-1-9. LCD BLOCK ASSEMBLY (TRV series) ND801 - 1 0 LCD901 LCD903 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref.
Page 153: Zoom Lens Block Assembly
6-1-10. ZOOM LENS BLOCK ASSEMBLY not supplied M906 M905 IC401 Be sure to read “Note on the CCD Imager replacement” on page 4–9 when changing the CCD imager. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 8-848-722-01 DEVICE, LENS LSV-600A (SOC) A-7073-786-A CD-210 (NT) BOARD, COMPLETE (TR series) 3-713-791-51 SCREW (M1.7 x 3.5), TAPPING, P2...
Page 154: Cassette Compartment Assembly
6-1-9. CASSETTE COMPARTMENT ASSEMBLY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7040-421-A DAMPER ASSY X-3945-399-1 GEAR ASSY, GOOSENECK 7-624-102-04 STOP RING 1.5, TYPE -E 3-947-503-01 SCREW (M1.4 x 2.5) X-3945-400-X CASSETTE COMPARTMENT ASSY 3-331-007-21 WASHER 3-965-587-03 SPRING, TENSION 3-727-176-01 WASHER, STOPPER 3-965-584-08 RETAINER, GOOSENECK...
Page 155: Ls Chassis Assembly
6-1-10. LS CHASSIS ASSEMBLY S002 S001 D001 FP-249 (not supplied) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7040-419-A BASE (S) BLOCK ASSY, GUIDE 3-965-563-01 GEAR, T SOFT A-7040-418-B BASE (T) BLOCK ASSY, GUIDE 3-965-559-01 STOPPER (T) 3-965-565-01 CLAW, T SOFT 3-965-557-01 STOPPER (T), GB X-3945-397-1 DECK ASSY, REEL, S...
Page 156: Mechanism Chassis Assembly
6-1-11. MECHANISM CHASSIS ASSEMBLY M901 81 1 M903 M902 S901 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3947-343-1 GROUND (IM) ASSY, SHAFT 3-965-535-01 SPRING (LIMITTER ARM S), COIL 3-965-550-02 SCREW (M1.7X1.6) 3-965-542-01 SHIELD, MOTOR 1-657-785-11 FP-248 FLEXIBLE BOARD (DEW SENSOR) 3-965-539-01 GEAR (A)
Page 157: Electrical Parts List
CD-210/211 CF-60/61 6-2. ELECTRICAL PARTS LIST Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by In each case, u: µ , for example: may be different from the parts specified in the mark ! or dotted line with mark uA...: µ...
Page 158 CF-60/61 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > < SWITCH > D001 8-719-062-16 DIODE 01ZA8.2(TPL3) S003 1-771-138-61 SWITCH, KEY BOARD (DATE) (TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E) S004 1-771-029-21 SWITCH, TACTILE (PROGRAM AE) D005 8-719-073-03 DIODE MA8082-(K8).S0 (TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E) D006 8-719-073-03 DIODE MA8082-(K8).S0...
Page 159 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C812 1-162-964-11 CERAMIC CHIP 0.001uF C865 1-117-720-11 CERAMIC CHIP 4.7uF C813 1-162-964-11 CERAMIC CHIP 0.001uF (TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E) C815 1-162-964-11 CERAMIC CHIP 0.001uF C866 1-164-505-11 CERAMIC CHIP 2.2uF C817 1-113-991-11 TANTAL.
Page 160 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark L806 1-424-675-51 INDUCTOR 33uH Q828 8-729-037-74 TRANSISTOR UN9213J-(K8).SO (TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E) L807 1-424-674-11 INDUCTOR 22uH Q828 8-729-042-29 TRANSISTOR RN1104F(TPL3) L807 1-424-674-51 INDUCTOR 22uH (TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E) L808 1-424-674-11 INDUCTOR 22uH Q829 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3) L808 1-424-674-51 INDUCTOR...
Page 161 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R812 1-218-901-11 RES,CHIP 180K 0.50% 1/16W R875 1-216-849-11 METAL CHIP 220K 1/16W R813 1-216-853-11 METAL CHIP 470K 1/16W (TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E) R814 1-218-879-11 RES,CHIP 0.50% 1/16W R876 1-216-845-11 METAL CHIP 100K 1/16W R815...
Page 162 DD-117 FP-249 FP-355 LB-54 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R917 1-216-864-11 METAL CHIP 1/16W A-7073-439-A LB-54 BOARD, COMPLETE (TR516E) (TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E) ********************* (Ref. No. 10,000 Series) R918 1-216-849-11 METAL CHIP 220K 1/16W (TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E) < CAPACITOR > R921 1-216-296-91 SHORT R922...
Page 163 Part No. Description Remark Ref. No. Part No. Description Remark A-7073-782-A MA-345(B) BOARD, COMPLETE D302 8-749-060-65 DIODE DCC3810 D303 8-719-061-82 DIODE TLSU1002(TPX1,SONY) ************************* (TR515E/TR516E) D305 8-719-073-01 DIODE MA111-(K8).S0 (TR425E/TR515E/TR516E/TR713E/TRV27E/TRV27EP/TRV36E/TRV46E) A-7073-794-A MA-345(IB) BOARD, COMPLETE (TR713E) D309 8-719-067-44 DIODE CL-310IRS-X-TU (TR315E/TR415E/TR425E/TR515E/TR516E/TRV16E/TRV26E/TRV27E/ **************************...
Page 164 MA-345/346 PD-107 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R311 1-216-864-11 METAL CHIP 1/16W C5608 1-164-357-11 CERAMIC CHIP 1000PF (TR425E/TR515E/TR516E/TR713E/TRV27E/TRV27EP/TRV36E/TRV46E) C5610 1-162-926-11 CERAMIC CHIP 82PF R312 1-216-864-11 METAL CHIP 1/16W C5612 1-162-926-11 CERAMIC CHIP 82PF (TR713E/TRV46E) C5616 1-107-682-11 CERAMIC CHIP...
Page 165 PD-107 PJ-90/91 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q5606 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX R5684 1-216-805-11 METAL CHIP 1/16W R5685 1-216-845-11 METAL CHIP 100K 1/16W Q5607 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX R5686 1-216-845-11 METAL CHIP 100K 1/16W Q5608 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX Q5701 8-729-039-43 TRANSISTOR FP216-TL...
Page 166 PJ-90/91 SE-80/81 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CONNECTOR > C458 1-164-343-11 CERAMIC CHIP 0.056uF (TR713E/TRV46E) * CN101 1-764-521-11 CONNECTOR, FFC/FPC (ZIF) 12P C459 1-164-343-11 CERAMIC CHIP 0.056uF (TR713E/TRV46E) < DIODE > C460 1-110-666-11 ELECT CHIP 22uF 6.3V...
Page 167 SE-80/81 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < SENSOR > C042 1-162-970-11 CERAMIC CHIP 0.01uF C043 1-162-970-11 CERAMIC CHIP 0.01uF SE451 1-803-041-11 SENSOR, ANGULAR VELOCITY (PITCH) C048 1-162-970-11 CERAMIC CHIP 0.01uF (TR713E/TRV46E) C049 1-162-970-11 CERAMIC CHIP 0.01uF SE452...
Page 168 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C184 1-115-156-11 CERAMIC CHIP C347 1-162-970-11 CERAMIC CHIP 0.01uF C185 1-126-246-11 ELECT CHIP 220uF C349 1-162-970-11 CERAMIC CHIP 0.01uF C188 1-135-181-21 TANTALUM CHIP 4.7uF 6.3V C371 1-104-908-11 TANTAL. CHIP 47uF C190 1-107-826-91 CERAMIC CHIP...
Page 169 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C474 1-162-964-11 CERAMIC CHIP 0.001uF C570 1-162-970-11 CERAMIC CHIP 0.01uF C475 1-162-964-11 CERAMIC CHIP 0.001uF C571 1-135-201-11 TANTALUM CHIP 10uF C476 1-165-176-11 CERAMIC CHIP 0.047uF C572 1-135-201-11 TANTALUM CHIP 10uF C605 1-135-177-21 TANTALUM CHIP 1uF C478...
Page 170 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C768 1-162-909-11 CERAMIC CHIP 0.25PF 50V < FERRITE BEAD > (TR713E/TRV46E) C769 1-107-823-11 CERAMIC CHIP 0.47uF FB001 1-216-864-11 METAL CHIP 1/16W (TR713E/TRV46E) FB002 1-414-229-11 INDUCTOR CHIP 0uH C770 1-107-823-11 CERAMIC CHIP 0.47uF...
Page 171 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark L602 1-414-754-11 INDUCTOR 10uH Q309 8-729-042-29 TRANSISTOR RN1104F(TPL3) L751 1-412-948-11 INDUCTOR 5.6uH (TR713E/TRV46E) Q371 8-729-042-74 TRANSISTOR UN9216J-(K8).SO L752 1-412-957-11 INDUCTOR 33uH (TR713E/TRV46E) Q371 8-729-045-78 TRANSISTOR RN1110F(TPL3) Q452 8-729-037-74 TRANSISTOR UN9213J-(K8).SO L753 1-412-957-11 INDUCTOR...
Page 172 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R045 1-216-845-11 METAL CHIP 100K 1/16W R101 1-216-837-11 METAL CHIP 1/16W R046 1-216-821-11 METAL CHIP 1/16W R102 1-216-834-11 METAL CHIP 1/16W R047 1-216-864-11 METAL CHIP 1/16W R048 1-216-864-11 METAL CHIP 1/16W R103...
Page 173 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R233 1-216-824-11 METAL CHIP 1.8K 1/16W R382 1-216-837-11 METAL CHIP 1/16W R234 1-216-832-11 METAL CHIP 8.2K 1/16W (TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E) R235 1-216-824-11 METAL CHIP 1.8K 1/16W R383 1-216-837-11 METAL CHIP 1/16W R236 1-216-825-11 METAL CHIP...
Page 174 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R465 1-216-845-11 METAL CHIP 100K 1/16W R570 1-216-841-11 METAL CHIP 1/16W R466 1-216-841-11 METAL CHIP 1/16W R571 1-216-837-11 METAL CHIP 1/16W R467 1-216-833-11 METAL CHIP 1/16W R572 1-216-845-11 METAL CHIP 100K 1/16W...
Page 175 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R653 1-216-853-11 METAL CHIP 470K 1/16W R770 1-216-847-11 METAL CHIP 150K 1/16W R654 1-216-817-11 METAL CHIP 1/16W (TR713E/TRV46E) R655 1-216-853-11 METAL CHIP 470K 1/16W R771 1-216-818-11 METAL CHIP 1/16W R666 1-216-821-11 METAL CHIP...
Page 176 VF-99 VF-119 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7066-774-A VF-99 BOARD, COMPLETE R907 1-216-845-11 METAL CHIP 100K 1/16W R908 1-216-852-11 METAL CHIP 390K 1/16W ******************** (TR315E/TR415E/TR425E/TR515E/TR713E/TRV16E/TRV26E/TRV27E/ R909 1-216-833-11 METAL CHIP 1/16W TRV27EP/TRV36E/TRV46E) (Ref. No. 10,000 Series) R910 1-216-835-11 METAL CHIP 1/16W...
Page 177 VF-119 VF-120 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C5417 1-162-970-11 CERAMIC CHIP 0.01uF R5446 1-216-837-11 METAL CHIP 1/16W C5418 1-115-566-11 CERAMIC CHIP 4.7uF R5447 1-216-833-11 METAL CHIP 1/16W C5419 1-162-967-11 CERAMIC CHIP 0.0033uF 10% R5448 1-216-839-11 METAL CHIP 1/16W...
Page 178 VF-120 VL-21/22 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R5313 1-216-842-11 METAL CHIP 1/16W MISCELLANEOUS R5314 1-216-850-11 METAL CHIP 270K 1/16W ************* R5315 1-216-833-11 METAL CHIP 1/16W R5316 1-216-851-11 METAL CHIP 330K 1/16W 1-475-619-11 SWITCH BLOCK, CONTROL (SS-8500) 1-418-215-21 SWITCH BLOCK, CONTROL (FK-8500) R5317 1-216-848-11 METAL CHIP...
Page 179 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-865-335-31 MANUAL, INSTRUCTION (Arabic,Persia) SP901 1-504-753-41 SPEAKER (2.8 CM) (for TRV series) (E,CN models only : TR315E/TR516E) ! VL901 1-517-760-11 LIGHT, VIDEO (for Video light models) 3-865-335-41 MANUAL, INSTRUCTION (Chinese) ! V901 1-452-673-61 CRT ASSY (M01KXX90WB) (HK model only : TR315E/TR516E)
Page 180 Take a copy CAMERA COLOR REPRODUCTION FRAME and Parts reference sheets with a clear sheet for use. FOR CAMERA COLOR REPRODUCTION ADJUSTMENT CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E < PARTS REFERENCE SHEET > You can find the parts position of mount locations applying to boards of a set.
Page 181 CCD-TR315E/TR415E/TR425E/TR515E/TR516E/TR713E CCD-TRV16E/TRV26E/TRV27E/TRV27EP/TRV36E/TRV46E Sony Corporation 99A0978-1 Printed in Japan © 1999. 1 9-974-129-11 Personal A&V Products Company Published by Quality Engineering Dept. – 296 – (Shinagawa)

This manual is also suitable for:

Ccd-tr515e Ccd-tr415e Ccd-tr516e Ccd-tr713e Ccd-trv16e Ccd-trv26e ... Show all

Sony CCD-TR315E Service Manual

Service Note

Self-Diagnosis Function

General

Disassembly

Block Diagrams

Adjustments

Repair Parts List

Quick Links

Related Manuals for Sony CCD-TR315E

Summary of Contents for Sony CCD-TR315E

This manual is also suitable for:

Table of Contents