Page 1 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/ TRV46/TRV46PK RMT-708 SERVICE MANUAL US Model Canadian Model CCD-TR416/TR516/TR716 CCD-TRV16/TRV36/TRV43/TRV46 E Model Ver 1.0 1999.01 CCD-TR315/TR416PK/TR516PK CCD-TRV16/TRV16PK/TRV36PK/ TRV46/TRV46PK Photo : CCD-TR516 Hong Kong Model CCD-TRV16/TRV46 Taiwan Model CCD-TRV16 Brazilian Model CCD-TR315/TR416 CCD-TRV16 NTSC Photo : CCD-TRV46 B MECHANISM For MECHANISM ADJUSTMENTS, refer to the “8mm Video MECHANICAL ADJUSTMENT MANUAL VII”...
Page 2 COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS REMPLACER CES COMPOSANTS QUE PAR DES PIÉCES SONY PUBLISHED BY SONY. DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU...
Page 4 Supplied accessories 1 RMT-708 Wireless Remote Commander (1) 7 Shoulder strap (1) CCD-TR516/TR516PK/TR716 8 Video P6-15P HB tape CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK CCD-TR416: US/TR516: US/TR716:US 2 AC-L10A/L10B/L10C AC power adaptor CCD-TRV16:US/TRV36:US/TRV43:US/TRV46:US 3 NP-F330 Battery pack (1) 9 2 pin conversion adaptor (1) CCD- TR315//TR416PK/TR516PK 4 CR2025 Lithium Battery (1) CCD- TRV16:E,BR,HK,TW/TRV16PK/TRV36PK/ TRV46:E,HK/TRV46PK...
Page 5: Service Note
SERVICE NOTE 1. POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. Battery switch This following three methods are available to prevent this.
Page 6: Self-Diagnosis Function
SELF-DIAGNOSIS FUNCTION 1. Self-diagnosis Function 2. Self-diagnosis display When problems occur while the unit is operating, the self-diagno- When problems occur while the unit is operating, the counter of the sis function starts working, and displays on the viewfinder or Dis- viewfinder or Display window shows a 4-digit display consisting play window what to do.
Page 7: Self-Diagnosis Code Table
4. Self-diagnosis Code Table Self-diagnosis Code Symptom/State Correction Block Detailed Function Code Condensation. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Video head is dirty. Non-standard battery is used. Use the InfoLITHIUM battery. LOAD direction.
Page 8: Table Of Contents
TABLE OF CONTENTS SERVICE NOTE 2. DISASSEMBLY 1. Power Supply During Repairs ..........5 2-1. Removal of Front Panel Block and Video Light Block ..2-1 2. To Take out a Cassette when not Eject (Force Eject) ....5 2-2. Removal of LB-54, VF-119 and VF-120 Boards (Color View Finder Models) ....
Page 9 4. PRINTED WIRING BOARDS AND SCHEMATIC 5. ADJUSTMENTS DIAGRAMS 5-1. CAMERA SECTION ADJUSTMENTS ......5-1 1-1. Preparations before Adjustment (Camera Section) ..5-1 4-1. Frame Schematic Diagram (1) ........... 4-1 1-1-1. List of Service Tools ..........5-1 • Frame Schematic Diagram (2) ........4-4 1-1-2.
Page 10 5-2. MECHANICAL SECTION ADJUSTMENT ....5-34 3-5. IR Transmitter Adjustments 2-1. Operating without a Cassette .......... 5-34 (CCD-TRV43/TRV46/TRV46PK) ......5-56 2-2. Tape path Adjustment ............. 5-34 IR Video Carrier Frequency Adjustment Preparations for adjustments ........5-34 (VC-215 board) ............5-56 IR Video Deviation Adjustment (VC-215 board) ..
Page 11: General
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK This section is extracted SECTION 1 from instruction manual of GENERAL CCD-TRV36/TRV43/TRV46.
Page 31: Disassembly
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 2 DISASSEMBLY The equipment can be removed using the following procedure. VIDEO CAMERA RECORDER 2-2. LB-54/VF-119 & 120 BOARDS 2-1. FRONT PANEL BLOCK 2-5. CASSETTE LID ASSEMBLY (Color view finder models only) VIDEO LIGHT BLOCK 2-3. CRT/VF-99 BOARD (Video light models only) (B/W view finder models only) 2-4.
Page 32: Removal Of Lb-54, Vf-119 And Vf-120 Boards (Color View Finder Models)
2-2. REMOVAL OF LB-54, VF-119 AND VF-120 BOARDS (Color view finder model CCD-TR416/TR416PK/TR516/TR516PK/TR716 Tilt-up the EVF block to the direction of arrow A . FP-57 flexible board CN5401,20P Remove the EVF rear cabinet assembly to the direction of arrow B . Flexible retainer sheet !£...
Page 33: Removal Of Cabinet (R) Block
2-4. REMOVAL OF CABINET (R) BLOCK Note : Be sure to that the pin of the Lens assembly is put into the hole of the IR knob when attaching. (TR series) (TRV series) Flat cable (FFC-257F) Flat cable (FFC-257F) CN911, 45P CN911, 45P Two screws Two screws...
Page 34: Removal Of Cabinet (L) Block
2-7. REMOVAL OF CABINET (L) BLOCK 2-8. REMOVAL OF CONTROL SWITCH BLOCK Function Key Switch (FK-8500) Cabinet (L) block Remove the Function key switch in the direction of arrow with pushing Screwdriver( - ) the claw. Two claws Flexible connector CN935, 10P Flexible connector CN934,12P...
Page 35: Removal Of Vc-215 Abd Se-80/81 Boards
2-11. REMOVAL OF VC-215 AND SE-80/81 BOARDS FP-56 flexible board FP-220 flexible board CN916, 18P Flexible board CN901, 8P from loading motor CN001, 16P Screw (M2x3) from video head FP-621 flexible board CN902, 12P Flexible board CN905, 10P from drum motor FP-620 flexible board (VC side) CN904, 10P (SE side) CN650, 10P...
Page 36: Removal Of Tr Cover, Cf-60 Board And Display Panel (Tr Series)
2-13. REMOVAL OF TR COVER, CF-60 BOARD AND DISPLAY PANEL ...(TR series) !∞ Liquid crystal display panel Phase adjustment S024 !¢ LCD holder S015 FP-57 flexible board...(Color EVF type only) CN007, 20P Claw !™ Flat cable (FFC-235)...(B/W EVF type only) CF-60 board CN008, 4P !¡...
Page 37: Service Position
2-15. SERVICE POSITION Preparation : Refer to previous section “DISASSEMBLY”, and con- CPC-7 jig (J-6082-382-A) nect as shown in the figure after each parts has been VC-215 board : CN910, 16P removed. Extension cord 70P (J-6082-439-A) —TR series— DD-117 board : CN931 — VC-215 board : CN915 VC-215 board Screw (M2x3) Control switch block...
Page 38: Circuit Boards Location
2-16. CIRCUIT BOARDS LOCATION LB-54... Color EVF models only (Back light) VF-119... Color EVF models only (Color EVF) VF-120... Color EVF models only (Color EVF) CF-60... TR series only DD-117 (Control) (Power) VL-21... TR516/TR516PK/TR716 VF-99... B/W EVF models only VL-22... TRV36/TRV36PK/TRV43/ (B/W EVF) TRV46/TRV46PK...
Page 45 FRPV FRPT...
Page 49 MODEL) (B/W...
Page 51 Blue Magenta Blue White...
Page 71 PUSH 5SEC MODE...
Page 82: Adjustments
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 5 ADJUSTMENTS Refer to page 3 as Table for distinction functions of models and classification 5-1. CAMERA SECTION ADJUSTMENTS 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope •...
Page 83: Preparations
1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. 1) Connect the equipment for adjustments according to Fig. 5-1-3, 2) By setting the “Forced Camera Power ON mode”, the camera power can be turned ON even if the front panel block (MA-345/ Pattern box...
Page 84 TR MODEL Color monitor Vector scope Terminated at 75 Ω Lens block CD-210 board Regulaterd power supply CN401 (8.4 ± 0.1 Vdc) Battery terminal (Note 1) Extension cable(16P) (J-6082-357-A) Adjusting VL-21 board remote CN151 commander Battery switch VIDEO terminal LANC CN935 CN909 terminal...
Page 85 TRV MODEL Color monitor Vector scope Terminated at 75 Ω Lens block CD-211 board Regulaterd power supply CN401 (8.4 ± 0.1 Vdc) Battery terminal (Note 2) Extension cable(16P) (J-6082-357-A) Adjusting VL-22 board remote CN151 commander Battery switch VIDEO terminal LANC CN935 jack CN909...
Page 86: Precautions
1-1-3.Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. 1. POWER switch (MA-345/346 board) ....CAMERA 7. FOCUS switch (MF-8500) ........MANUAL 2. NIGHT SHOT switch (Lens Block) ........ OFF 8.
Page 87: Adjusting Remote Commander
1-1-4. Adjusting Remote Commander • Changing the address The adjusting remote commander is used for changing the calcula- The address increases when the FF ()) button is pressed, tion coefficient in signal processing, EVR data, etc. The adjusting and decreases when the REW (0) button is pressed. There remote commander performs bi-directional communication with the are altogether 256 addresses, from 00 to FF.
Page 88: Data Processing
1-1-5. Data Processing The calculation of the DDS display and the adjusting remote calculate and convert the result to hexadecimal notation, and use it commander display data (hexadecimal notation) are required for as the adjustment data. Table 5-1-2. indicates the hexadecimal obtaining the adjustment data of some adjustment items.
Page 89: Initialization Of D, E, F
1-2. INITIALIZATION OF D, E, F PAGE DATA 2. Modification of D, E, F Page Data If the D, E, F page data has been initialized, change the data of the 1. Initializing the D,E,F Page Data “Fixed data-2” address shown in the following tables by manual Note 1: If “Initializing the D, E, F Page Data”...
Page 90: D Page Table
3. D Page Table Note1 : Fixed data-1 : Initialized data. (Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Address Initial Remark Address Initial Remark Value Value 00 to 0F...
Page 91: F Page Table
4. F Page table Address Initial Remark Note 1: Value Fixed data-1 : Initialized data. Auto white balance adj. ( Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. IRIS IN/OUT adj. (Refer to “2. Modification of D, E, F Page Data”). Note 2 : There are three models classified by VTR formats as shown Flange back adj.
Page 92 Address Initial Remark Address Initial Remark Value Value Fixed data-2 Switching position adj. Fixed data-1 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1:CCD-TR516/TR516PK, TRV36/TRV36PK Fixed data-2:CCD-TR716, TRV43/TRV46/TRV46PK Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-2 Fixed data-1...
Page 93: E Page Table
5. E Page Table Address Initial Remark Note 1: Value Fixed data-1 : Initialized data. Fixed data-1 ( Refer to “1. Initializing the D,E,F Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of D, E, F Page Data”). Fixed data-2 Note 2: See “1-5.
Page 94 Address Initial Remark Address Initial Remark Value Value Fixed data-1 Fixed data-2 Fixed data-1 TR model:Fixed data-1/TRV model:Fixed data-2 Fixed data-2 Fixed data-1 Fixed data-1 Fixed data-2 Fixed data-1 TR model:Fixed data-1/TRV model:Fixed data-2 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1...
Page 95: Camera System Adjustments
1-3. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, Check that the specified value of “28MHz Origin Oscillation Adjustment”, “Y OUT level Adjustment” and “C OUT level Adjustment” of “VIDEO SYSTEM ADJUSTMENT” are satisfied. 1. G-CAM flip Adjustment Set the color reproduction conditions to optimum. Subject Color bar chart standard picture frame Measurement Point...
Page 96: Hall Adjustment
2. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain and offset. Subject Not required Measurement Point DDS display data of LCD or TV monitor (Note 3) Measuring Instrument Adjustment Page Adjustment Address 2F, 30 Specified Value 7E to 82 during IRIS OPEN (Note 1) 13 to 17 during IRIS CLOSE (Note 2)
Page 97: Flange Back Adjustment
3. Flange Back Adjustment 3-2. Flange Back Adjustment (2) The inner focus lens flange back adjustment is carried out auto- Perform this adjustment after performing “Flange Back Adjustment matically. In whichever case, the focus will be deviated during auto (1)”. focusing/manual focusing.
Page 98: Flange Back Check
4. Flange Back Check 5. Picture Frame Setting Subject Siemens star chart Subject Color bar chart standard picture frame (2.0 m from the front of the lens) (1.5m from the front of the lens) (Luminance: approx. 200 lux) Measurement Point Video output terminal Measurement Point Check operation on TV monitor...
Page 99: Color Reproduction Adjustment
6. Color Reproduction Adjustment Adjust the color Separation matrix coefficient so that proper color reproduction is produced. Subject Color bar chart standard picture frame Measurement Point Video output terminal Measuring Instrument Vectorscope Adjustment Page Adjustment Address 34, 36, F5, F6 Specified Value All color luminance points should settle within each color reproduction frame.
Page 100: Iris In/Out Adjustment
7. IRIS IN/OUT Adjustment 8. MAX GAIN Adjustment For the unit to judge if the white balance is indoors or outdoors in Setting the minimum illumination. auto white balance operations, measure the light level and write it If it is not consistent, the image level required for taking subjects in in the EEPROM.
Page 101: Auto White Balance Standard Data Input
9. Auto White Balance Standard Data Input 10. Auto White Balance Adjustment Adjust to the proper auto white balance output data. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color bar standard picture frame) be poor.
Page 102: White Balance Check
11. White Balance Check Subject Clear chart (Color bar standard picture frame) Filter Filter C14 for color temperature correction ND filter 1.0 and 0.3 2 mm Measurement Point video output terminal Measuring Instrument Vectorscope Specified Value Fig. 5-1-11. A to C Switch setting: 1) NIGHT SHOT switch ............
Page 103: Angular Velocity Sensor Sensitivity Check
12. Angular Velocity Sensor Sensitivity Check (CCD-TR716/TRV43/TRV46/TRV46PK) • This adjustment is performed only when replacing the angular velocity sensor. Although this adjustment need not be performed when the circuit is damaged, etc., check the operations. • Note down the sensitivity displayed on the angular velocity sensor of the repair parts.
Page 104: (Ccd-Tr416/Tr416Pk/Tr516/Tr516Pk/Tr716)
1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM 1. EVF Initial Data Input ADJUSTMENT Mode VTR stop (CCD-TR416/TR416PK/TR516/TR516PK/TR716) Signal No signal Note 1: The back light (fluorescent tube) is driven by a high volt- Adjustment Page age AC power supply. Therefore, do not touch the back Adjusting Address C2 to CD light holder to avoid electrical shock.
Page 105: Vco Adjustment (Vf-119 Board)
2. VCO Adjustment (VF-119 board) 3. Bright Adjustment (VF-119 board) Set the VCO free-run frequency. If deviated, the EVF screen will be Set the level of the VIDEO signal for driving the LCD to the speci- blurred. fied value. If deviated, the screen image will be blackish or satu- rated (whitish).
Page 106: Contrast Adjustment (Vf-119 Board)
4. Contrast Adjustment (VF-119 board) 5. Backlight Consumption Current Adjustment (VF-120 Set the level of the VIDEO signal for driving the LCD to the speci- board) fied value. If deviated, the screen image will be blackish or satu- Set the backlight luminance and color temperature. rated (whitish).
Page 107: Monochrome Electronic Viewfinder System Adjustments
1-5. MONOCHROME ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENTS Note: CCD-TR315 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/ TRV46/TRV46PK 1-5-2. Centering Adjustment 1-5-1. Horizontal Slant Check Mode Playback Mode Playback Signal Alighment tape : Signal Alighment tape : For checking operations For checking operations (WR5-5NSP) (WR5-5NSP) Monoscope section Monoscope section Specified Value ±...
Page 108: Aberration Adjustment
1-5-4. Aberration Adjustment 1-5-5. Horizontal Amplitude Adjustment (VF-99 board) Mode VTR stop Signal Dot pattern Mode Playback Specified Value b1 2 • a1 Signal Alighment tape : b2 0.8 • a2 For checking operations (WR5-5NSP) Adjusting method: Monoscope section 1) Adjust the aberration adjustment ring so that the tracing of the Adjusting Element C909 (SOL901) dot satisfies the specified value.
Page 109: Vertical Amplitude Adjustment (Vf-99 Board)
1-5-6. Vertical Amplitude Adjustment (VF-99 board) 1-5-7. Brightness Adjustments (VF-99 board) Mode Playback Mode Playback Signal Alighment tape : Signal Alighment tape : For checking operations For checking operations (WR5-5NSP) (WR5-5NSP) Monoscope section Monoscope section Adjusting Element RV903 Specified Value RV904 Specified Value 10 ±...
Page 110: Lcd System Adjustment (Trv Series)
1-6. LCD SYSTEM ADJUSTMENT (TRV series) 1. LCD Initial Data Input Note1: The back light (fluorescent tube) is driven by a high volt- Mode VTR stop age AC power supply. Therefore, do not touch the back Signal Arbitrary light holder to avoid electrical shock. Adjustment Page Note2: When replacing the LCD unit, be careful to prevent dam- Adjustment Address...
Page 111: Vco Adjustment (Pd-107 Board)
2. VCO Adjustment (PD-107 board) 3. D range Adjustment (PD-107 board) Set the VCO freerun frequency. If deviated, the LCD screen will be Set the D range of the RGB decoder used to drive the LCD to the blurred. specified value. If deviated, the LCD screen will become blackish or saturated (whitish).
Page 112: Bright Adjustment (Pd-107 Board)
4. Bright Adjustment (PD-107 board) 5. Contrast Adjustment (PD-107 board) Set the level of the VIDEO signal for driving the LCD to the speci- Set the level of the VIDEO signal for driving the LCD to the speci- fied value. If deviated, the screen image will be blackish or satu- fied value.
Page 113: V-Com Adjustment (Pd-107 Board)
6. V-COM Adjustment (PD-107 board) 7. Color Adjustment (PD-107 board) Set the common electrode drive signal level of LCD to the specified Set the color saturation to the standard value. If deviated, the color value. will be to dark or light. Mode VTR stop Mode...
Page 114: V-Com Adjustment (Pd-107 Board)
8. V-COM Adjustment (PD-107 board) 9. White Balance Adjustment (PD-107 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and con- Mode VTR stop...
Page 115: Mechanical Section Adjustment
5-2. MECHANICAL SECTION ADJUSTMENT 6) Connect the oscilloscope. Channel 1: Pin 6 of CN910 of VC-215 board External trigger: Pin !¡ of CN910 of VC-215 board Mechanism Parts Adjustments Connect the oscilloscope via the CPC-7 jig (J-6082-382-A). For details on the adjustments and checks of mechanical section 7) Playback the alignment tape for tracking.
Page 116: Video Section Adjustments
5-3. VIDEO SECTION ADJUSTMENTS When performing adjustments, refer to the layout diagrams for adjustment related parts beginning from page 5-60. 3-1. PREPARATIONS BEFORE ADJUSTMENT The following adjusting instruments are used for adjusting the video section. 3-1-1. Equipments to be Used 1) TV monitor 2) Oscilloscope: 2 phenomena, band 30 MHz or wider, with delay mode.
Page 117: Precautions On Adjusting
3-1-2. Precautions on Adjusting 3-1-3. Adjusting Connectors 1) The adjustments of this unit are performed in the VTR mode or Some of the adjusting points of the video section are concentrated camera mode. at VC-215 board CN910. Connect the measuring instruments via To set to the VTR mode, set the power switch to “VTR”...
Page 118: Connecting The Equipments
3-1-4. Connecting the Equipments Connect the measuring instruments as shown in Fig. 5-3-2 and perform the adjustments. Connecting the TV Monitor and Regulated Power Supply Battery terminal Main Unit TV monitor Regulated power supply 8.4 ± 0.1Vdc VIDEO Connect when using the camera mode or playing back.
Page 119 Note: Measure using the VIDEO terminal (Terminated at 75 Ω). Fig. 5-3-3. shows the 75% color bar signals recorded on the align- ment tape. Fig. 5-3-3. Color Bar Signals of the Alignment Tape...
Page 120: Output Level And Impedance
3-1-6. Output Level and Impedance 3-1-8. Service Mode Video output Additional note on adjustment Note: After the completion of the all adjustments, cancell the ser- Phono jack, 1 Vp-p, 75Ω, unbalanced, sync negative vice mode by either of the following ways. Audio output Phono jack, –7.5 dBs, (at load impedance 47 kΩ), 1) Unplug the main power supply and remove the lithium battery.
Page 121: Emergency Memory Address
2. Emergency Memory Address 2-1. EMG CODE (Emergency Code) The codes shown in the following table which correspond to errors Page F Address 10 to 1B that occur are recorded in addresses 10, 14, and 18. Address Contents Type of Emergency Code 1st EMG code No error...
Page 122: Msw Codes
2-2. MSW Codes • The lower parts of the data of addresses 12, 16 and 1A represent the MSW codes (mode switch, mechanism position) when errors occurs. • The upper parts of the data of addresses 12, 16 and 1A represent, when the mechanism position is to be moved, the MSW codes at the start of movement (when moving the loading motor).
Page 123: Bit Value Discrimination
3. Bit value discrimination 4. Switch check (1) Bit values must be discriminated using the display data of the ad- Page 3 Address 43 justing remote commander for the following items. Use the table below to discriminate if the bit value is “1” or “0”. Function When bit value=1 When bit value=0 0 VTR MODE SW...
Page 124: Switch Check (2)
5. Switch check (2) Page 3 Address 60 to 66 Using method: 1) Select page: 3, address: 60 to66. 2) By discriminating the display data, the pressed key can be dis- c r i m i n a t e d . Data Address 00 to 0D...
Page 125: Led, Lcd (Display Window) Check
8. LED, LCD (display window) check 9. Record of Use Check Page 3 Address 05 Bit5 Page 3 Address A2 to AA Address Function Remarks Using method: 1) Select page: 3, address: 05, and set the bit value of Bit5 to “1”. 1000th place digit and 2) Check that all LED are lit and all segments of LCD (display 100th place digit of...
Page 126: System Control System Adjustment
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Initialization of D, E, F Page Data If the D, E, F page data is erased due to some reason, perform “1-2. INITIALIZATION OF D, E, F PAGE DATA”, of “5-1. CAMERA SECTION ADJUSTMENT”. 2.
Page 127: Servo System Adjustments
3-3. SERVO SYSTEM ADJUSTMENTS 2. RF Switching Position Adjustment (VC-215 Board) If deviated in this case causes switching noise or jitter on the played 1. CAP FG Offset Adjustment (VC-215 board) back screen. Improve the capstan servo characteristic. If it is not correct. jitters Mode Playback will increase.
Page 128: Video System Adjustments
3-4. VIDEO SYSTEM ADJUSTMENTS 1. 28 MHz Origin Oscillation Adjustment (VC-215 board) Set the frequency of the clock for synchronization. Video system adjustments must be performed in the following order. If deviated, the synchronization will be disrupted and the color will become inconsistent.
Page 129: Afc F0 Adjustment (Vc-215 Board)
2. AFC f0 Adjustment (VC-215 board) 3. Filter f0 Adjustment (VC-215 board) Adjust the pull-in range of the A/D converted clock generator dur- Minimize the chroma signal residual components during compos- ing playback. ite video signal input. Mode VTR stop Mode VTR stop Signal...
Page 130: Y Out Level Adjustment (Vc-215 Board)
4. Y OUT Level Adjustment (VC-215 board) 5. C OUT Level Adjustment (VC-215 board) Set the Y signal output level. Set the chroma signal output level. Mode VTR stop Mode VTR stop Signal No signal Signal No signal Measurement Point VIDEO terminal (75Ω...
Page 131: Rp Filter F0 Adjustment (Vc-215 Board)
6. RP Filter f0 Adjustment (VC-215 board) Adjust the LPF of the playback RF amplifier. Mode VTR stop Signal No signal Pin 9 of CN910 (RF AGC OUT) Measurement Point Measuring Instrument Oscilloscope Adjustment Page Adjustment Address Specified Value A = Below 10mVp-p Connection: 1) Input a 14.2MHz, 400mVp-p CW signal to Pin 7 of CN910 (RF AGC IN).
Page 132: Hi8 Rec Y Current Adjustment (Vc-215 Board)
7. Hi8 REC Y Current Adjustment (VC-215 board) 14) Write the following data in page: F, address: 57 to 5A. CCD-TR516/TR516PK/TR716 Address Data CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK Adjust the Y FM signal recording current. Mode VTR recording (SP mode) Signal No signal Pin !º of CN910 (REC RF) Measurement Point Note: After setting each data, be sure to press the PAUSE button Measuring Instrument Oscilloscope...
Page 133: Ccd-Trv16/Trv16Pk
8. Standard8 REC Y Current Adjustment (VC-215 board) 14) Write the following data in page: F, address: 57 to 5A. CCD-TR315/TR416/TR416PK Address Data CCD-TRV16/TRV16PK Adjust the Y FM signal recording current. Mode VTR recording (SP mode) Signal No signal Pin !º of CN910 (REC RF) Measurement Point Note: After setting each data, be sure to press the PAUSE button Measuring Instrument...
Page 134: Hi8 Rec L Level Adjustment (Vc-215 Board)
9. Hi8 REC L Level Adjustment (VC-215 board) 13) Calculate the adjustment data (hexadecimal) from the follow- CCD-TR516/TR516PK/TR716 ing equations (hexadecimal calculation), and input each adjust- CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK ment address. (Refer to Table 5-1-2. Hexadecimal-Decimal Set the recording levels of the REC AFM signal and REC ATF sig- conversion Table.) nal.
Page 135: Standerd8 Rec L Level Adjustment (Vc-215 Board) (Ccd-Tr315/Tr416/Tr416Pk Ccd-Trv16/Trv16Pk)
10. Standard8 REC L Level Adjustment (VC-215 board) 14) Write the following data in page: F, address: 63 to 64. CCD-TR315/TR416/TR416PK Address Data CCD-TRV16/TRV16PK Set the recording levels of the REC AFM signal and REC ATF sig- nal. If the level is too low, the audio S/N will deteriorated, tracking will not be stable, or SP/LP will not be discriminated properly.
Page 136: Rec C Current Adjustment (Vc-215 Board)
11. REC C Current Adjustment (VC-215 board) 14) Select page: 0, address: 01, and set data: 01. Set the recording current levels of the REC Chroma signal. If it is 15) Select page: D, address: 14, and set the data memorized at step too low, chroma signal noise in played back picture will increased.
Page 137: Ir Transmitter Adjustments (Ccd-Trv43/Trv46/Trv46Pk)
3-5. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (VC-215 board) (CCD-TRV43/TRV46/TRV46PK) Mode Camera standby Subject Arbitrary Adjust using a IR receiver jig (J-6082-383-A). Measurement Point VIDEO OUT terminal of IR receiver jig (Terminated at 75Ω) Switch setting: Measuring Instrument Oscilloscope LASER LINK ....
Page 138: Ir Audio Deviation Adjustment (Vc-215 Board)
3. IR Audio Deviation Adjustment (VC-215 board) Mode VTR recording Signal Audio signal : 400Hz, –7.5dBs : AUDIO terminal Video signal : Color bar signal : VIDEO terminal Measurement Point AUDIO terminal of IR receiver jig ( Terminated at 47kΩ) Measuring Instrument Audio level meter Adjustment Page...
Page 139: Mhz Deviation Adjustment (Vc-215 Board)
3-6. AUDIO SYSTEM ADJUSTMENT 1. 1.5 MHz Deviation Adjustment (VC-215 board) Adjust to the optimum audio FM signal distortion. [Connecting the measuring instruments for the audio] If the adjustment is not correct, its playback level will differ from Connect the audio system measuring instruments besides the video that of other units.
Page 141: Repair Parts List
CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: The components identified by mark ! or dotted line with mark • Items marked “*” are not stocked since they are • Abbreviation ! are critical for safety. seldom required for routine service. Some delay Canadian model is abbreviated as CND.
Page 142: Cabinet (L) And Battery Panel Assembly
6-1-2. CABINET (L) AND BATTERY PANEL ASSEMBLY not supplied not supplied not supplied not supplied J901 See page 6-6 not supplied S003 J001 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-962-826-01 SCREW (2 x 4) 3-987-717-01 SCREW, TRIPOD 3-948-339-61 TAPPING 3-987-679-01 SHEET METAL (LOWER), STRAP...
Page 143: Front Panel Block Assembly
6-1-3. FRONT PANEL BLOCK ASSEMBLY Video light model CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK No video light CCD-TR315/TR416/TR416PK model CCD-TRV16/TRV16PK - 3 4 not supplied not supplied not supplied not supplied No video light models LAMP,HALOGEN MIC901 VL901 XB-3D(DC6V/3W) Video light models The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la...
Page 144: Cabinet (R) Block Assembly (Tr Series)
6-1-4. CABINET (R) BLOCK ASSEMBLY (TR series) not supplied See pages 6-7 to 6-8 LCD903 B/W view finder CCD- TR315 model Color view finder CCD- TR416/TR416PK/TR516/ model TR516PK/TR716 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-475-620-11 SWITCH BLOCK, CONTROL (MF-8500) A-7073-821-A CF-60 (N) BOARD, COMPLETE (TR315) X-3949-179-1 CABINET (R) ASSY (TR516/TR516PK/TR716)
Page 145: Cabinet (R) Block Assembly (Trv Series)
6-1-5. CABINET (R) BLOCK ASSEMBLY (TRV series) See page 6-8 not supplied not supplied SP901 See page 6-9 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-475-620-11 SWITCH BLOCK, CONTROL (MF-8500) X-3949-321-1 COVER ASSY, IR (TRV36/TRV36PK) X-3949-280-1 CABINET (R) ASSY X-3949-404-1 COVER ASSY, IR (TRV16:TW) (TRV36/TRV36PK/TRV43/TRV46/TRV46PK)
Page 146: Main Boards Block Assembly
6-1-6. MAIN BOARDS BLOCK ASSEMBLY Video light model CCD-TR516/TR516PK/TR716 CCD-TRV36/TRV36PK/TRV43/TRV46/TRV46PK No video light CCD-TR315/TR416/TR416PK model CCD-TRV16/TRV16PK No video light models See page 6-10 not supplied - 1 1 - 2 1 Video light models SE452 See pages 6-11 to 6-13 SE451 CCD-TR716 &...
Page 147 6-1-7. COLOR EVF BLOCK ASSEMBLY (Color View Finder models CCD-TR416/TR416PK/TR516/TR516PK/TR716) Note : As for the model whitch carries a B/W view finder, refer to page 6-8. LCD902 not supplied ND5351 not supplied The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety.
Page 148: B/W Evf Block Assembly (Ccd-Tr315 And Trv Series)
6-1-8. B/W EVF BLOCK ASSEMBLY (B/W View Finder models CCD-TR315 and TRV series) Note : As for the model whitch carries a color view finder, refer to page 6-7. V901 The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety.
Page 149: Lcd Block Assembly (Trv Series)
6-1-9. LCD BLOCK ASSEMBLY (TRV series) ND801 - 1 0 LCD901 LCD903 The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety. sécurité. Replace only with part number Ne les remplacer que par une specified.
Page 150: Zoom Lens Block Assembly
6-1-10. ZOOM LENS BLOCK ASSEMBLY not supplied M906 M905 IC401 Be sure to read “Note on the CCD Imager replacement” on page 4–8 when changing the CCD imager. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 8-848-722-01 DEVICE, LENS (LSV-600A) 1-668-959-11 FP-623 FLEXIBLE BOARD 3-713-791-51 SCREW (M1.7 x 3.5), TAPPING, P2...
Page 151: Cassette Compartment Assembly
6-1-11. CASSETTE COMPARTMENT ASSEMBLY See page 6-13 See page 6-12 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7040-421-A DAMPER ASSY X-3945-399-1 GEAR ASSY, GOOSENECK 7-624-102-04 STOP RING 1.5, TYPE -E 3-947-503-01 SCREW (M1.4X2.5) X-3949-153-2 CASSETTE COMPARTMENT ASSY 3-331-007-21 WASHER 3-965-587-03 SPRING (POWER, TENSION), TENSION 3-727-176-01 WASHER, STOPPER...
Page 152: Ls Chassis Assembly
6-1-12. LS CHASSIS ASSEMBLY S002 S001 D001 FP-249 (not supplied) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7040-419-A BASE (S) BLOCK ASSY, GUIDE 3-965-563-01 GEAR, T SOFT A-7040-418-B BASE (T) BLOCK ASSY, GUIDE 3-965-559-01 STOPPER (T) 3-965-565-01 CLAW, T SOFT 3-965-557-01 STOPPER (T), GB X-3945-397-1 DECK ASSY, REEL, S...
Page 153: Mechanism Chassis Assembly
6-1-13. MECHANISM CHASSIS ASSEMBLY M901 81 1 M903 M902 S901 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3947-343-1 GROUND (IM) ASSY, SHAFT 3-965-535-01 SPRING (LIMITTER ARM S), COIL 3-965-550-02 SCREW (M1.7X1.6) 3-965-542-01 SHIELD, MOTOR 1-657-785-11 FP-248 FLEXIBLE BOARD (DEW SENSOR) 3-965-539-01 GEAR (A)
Page 154: Electrical Parts List
CD-210/211 CF-60/61 6-2. ELECTRICAL PARTS LIST Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by In each case, u: µ , for example: mark ! or dotted line with mark may be different from the parts specified in the uA...: µ...
Page 155 CF-60/61 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > S010 1-771-029-21 SWITCH, TACTILE (MENU) (TR315/TR416/TR416PK/TR516/TR516PK/TR716) Q001 8-729-402-42 TRANSISTOR UN5213-TX S010 1-771-138-61 SWITCH, KEY BOARD (MENU) (TR315/TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) S012 1-771-029-21 SWITCH, TACTILE (EXPOSURE) <...
Page 156 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C811 1-162-965-11 CERAMIC CHIP 0.0015uF 10% C864 1-113-985-11 TANTAL. CHIP 10uF C812 1-162-964-11 CERAMIC CHIP 0.001uF C865 1-117-720-11 CERAMIC CHIP 4.7uF C813 1-162-964-11 CERAMIC CHIP 0.001uF (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) C815 1-162-964-11 CERAMIC CHIP 0.001uF...
Page 157 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < COIL > Q815 8-729-046-98 TRANSISTOR CPH6702-TL Q819 8-729-046-98 TRANSISTOR CPH6702-TL L804 1-412-056-11 INDUCTOR CHIP 4.7uH (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) L805 1-409-532-41 INDUCTOR 33uH Q823 8-729-037-74 TRANSISTOR UN9213J-(K8).SO (TR315/TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) Q823 8-729-042-29 TRANSISTOR RN1104F(TPL3) L805...
Page 158 DD-117 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q856 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3) R852 1-218-851-11 RES,CHIP 1.5K 0.50% 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) Q932 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R853 1-216-849-11 METAL CHIP 220K 1/16W (TRV43/TRV46/TRV46PK) (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) Q932 8-729-042-29 TRANSISTOR RN1104F(TPL3) (TRV43/TRV46/TRV46PK) R854 1-218-887-11 RES,CHIP...
Page 159 FP-355 LB-54 FP-249 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R900 1-218-895-11 RES,CHIP 100K 0.50% 1/16W < HALL ELEMENT > R901 1-218-887-11 RES,CHIP 0.50% 1/16W H001 8-719-033-37 ELEMENT, HALL HW-105C R902 1-216-864-11 METAL CHIP 1/16W H002 8-719-033-37 ELEMENT, HALL HW-105C R903...
Page 160 1-216-864-11 METAL CHIP 1/16W R309 1-216-847-11 METAL CHIP 150K 1/16W D301 8-719-061-86 DIODE DCR2810 (TRV43/TRV46/TRV46PK) (TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) D302 8-749-060-65 DIODE DCC3810 D303 8-719-061-82 DIODE TLSU1002(TPX1,SONY) R310 1-216-824-11 METAL CHIP 1.8K 1/16W D305 8-719-073-01 DIODE MA111-(K8).S0 R311 1-216-841-11 METAL CHIP 1/16W (TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) R311...
Page 161 PD-107 MA-345/346 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R312 1-216-864-11 METAL CHIP 1/16W C5616 1-107-682-11 CERAMIC CHIP (TRV43/TRV46/TRV46PK) C5618 1-113-994-11 TANTAL. CHIP 6.8uF R313 1-216-864-11 METAL CHIP 1/16W C5619 1-162-970-11 CERAMIC CHIP 0.01uF R314 1-216-815-11 METAL CHIP 1/16W C5620...
Page 162 PD-107 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q5606 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX R5674 1-216-864-11 METAL CHIP 1/16W R5676 1-216-864-11 METAL CHIP 1/16W Q5607 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX Q5608 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX R5679 1-216-805-11 METAL CHIP 1/16W Q5701 8-729-039-43 TRANSISTOR FP216-TL R5680...
Page 163 PJ-90 SE-80/81 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > C466 1-162-970-11 CERAMIC CHIP 0.01uF (TR716/TRV43/TRV46/TRV46PK) D102 8-719-062-16 DIODE 01ZA8.2(TPL3) D103 8-719-062-16 DIODE 01ZA8.2(TPL3) < CONNECTOR > < JACK > CN451 1-766-646-21 CONNECTOR, FFC/FPC 10P (TR716/TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) J101 1-537-747-41 TERMINAL BOARD (VIDEO/AUDIO)
Page 164 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7094-112-A VC-215(ZSL0) BOARD, COMPLETE (TR315) C062 1-162-926-11 CERAMIC CHIP 82PF **************************** C065 1-162-970-11 CERAMIC CHIP 0.01uF C068 1-162-921-11 CERAMIC CHIP 33PF A-7094-117-A VC-215(VZB0) BOARD, COMPLETE C069 1-162-970-11 CERAMIC CHIP 0.01uF ***************************** (TRV36/TRV36PK)
Page 165 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C233 1-162-638-11 CERAMIC CHIP C412 1-162-969-11 CERAMIC CHIP 0.0068uF 10% C234 1-162-970-11 CERAMIC CHIP 0.01uF C414 1-164-156-11 CERAMIC CHIP 0.1uF C235 1-162-970-11 CERAMIC CHIP 0.01uF C415 1-164-156-11 CERAMIC CHIP 0.1uF C237 1-164-156-11 CERAMIC CHIP...
Page 166 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C522 1-107-826-91 CERAMIC CHIP 0.1uF C754 1-107-823-11 CERAMIC CHIP 0.47uF C523 1-115-467-11 CERAMIC CHIP 0.22uF (TRV43/TRV46/TRV46PK) C755 1-107-823-11 CERAMIC CHIP 0.47uF C524 1-162-962-11 CERAMIC CHIP 470PF (TRV43/TRV46/TRV46PK) C525 1-162-970-11 CERAMIC CHIP 0.01uF...
Page 167 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CN908 1-774-639-21 CONNECTOR, FFC/FPC 15P L003 1-414-406-11 INDUCTOR 220uH CN909 1-764-703-11 CONNECTOR, FFC/FPC (LIF) 4P L004 1-414-754-11 INDUCTOR 10uH (TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) L005 1-412-948-11 INDUCTOR 5.6uH CN910 1-766-346-21 CONNECTOR, FFC/FPC 16P CN911 1-785-760-21 CONNECTOR, FFC/FPC (ZIF) 45P L006...
Page 168 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q044 8-729-042-29 TRANSISTOR RN1104F(TPL3) R006 1-216-825-11 METAL CHIP 2.2K 1/16W Q151 8-729-037-61 TRANSISTOR RN2104F(TPL3) R007 1-216-829-11 METAL CHIP 4.7K 1/16W R008 1-216-814-11 METAL CHIP 1/16W Q153 8-729-040-77 TRANSISTOR 2SC5376-B(TE85L) R009 1-216-813-11 METAL CHIP 1/16W...
Page 169 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R087 1-216-821-11 METAL CHIP 1/16W R227 1-216-811-11 METAL CHIP 1/16W R088 1-216-864-11 METAL CHIP 1/16W R092 1-216-809-11 METAL CHIP 1/16W R228 1-216-813-11 METAL CHIP 1/16W R093 1-216-833-11 METAL CHIP 1/16W R229 1-216-805-11 METAL CHIP...
Page 170 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R377 1-216-834-11 METAL CHIP 1/16W R461 1-216-853-11 METAL CHIP 470K 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) R378 1-216-825-11 METAL CHIP 2.2K 1/16W R462 1-216-853-11 METAL CHIP 470K 1/16W (TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) R463 1-216-853-11 METAL CHIP 470K 1/16W R464...
Page 171 VC-215 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R565 1-216-833-11 METAL CHIP 1/16W R649 1-216-857-11 METAL CHIP 1/16W R566 1-216-835-11 METAL CHIP 1/16W R650 1-219-570-11 RES,CHIP 1/16W R567 1-216-825-11 METAL CHIP 2.2K 1/16W R651 1-216-845-11 METAL CHIP 100K 1/16W R569...
Page 172 VC-215 VF-99 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R768 1-216-847-11 METAL CHIP 150K 1/16W A-7066-792-A VF-99 (YM)(YS)(VHL4) BOARD, COMPLETE (TRV43/TRV46/TRV46PK) ************************************ R770 1-216-847-11 METAL CHIP 150K 1/16W (TR315/TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) (TRV43/TRV46/TRV46PK) (Ref.No. 10,000 Series) R771 1-216-818-11 METAL CHIP 1/16W (TRV43/TRV46/TRV46PK) <...
Page 173 VF-99 VF-119 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R910 1-216-835-11 METAL CHIP 1/16W C5421 1-162-927-11 CERAMIC CHIP 100PF R911 1-216-160-00 RES,CHIP 1/8W R912 1-216-857-11 METAL CHIP 1/16W C5422 1-135-259-11 TANTAL. CHIP 10uF 6.3V R916 1-218-879-11 RES,CHIP 0.50% 1/16W C5423...
Page 174 VF-119 VF-120 VL-21/22 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R5446 1-216-837-11 METAL CHIP 1/16W R5310 1-216-842-11 METAL CHIP 1/16W R5447 1-216-833-11 METAL CHIP 1/16W R5311 1-216-850-11 METAL CHIP 270K 1/16W R5448 1-216-839-11 METAL CHIP 1/16W R5312 1-216-843-11 METAL CHIP...
Page 175 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MISCELLANEOUS ACCESSORIES ************* ************ 1-475-619-11 SWITCH BLOCK, CONTROL (SS-8500) 1-467-574-21 REMOTE COMMANDER (RMT-708) 1-475-617-11 SWITCH BLOCK, CONTROL (FK-8500) (TR516/TR516PK/TR716/TRV36/TRV36PK/TRV43/TRV46/TRV46PK) (TR series/TRV16/TRV16PK/TRV36/TRV36PK) 1-475-599-11 ADAPTOR, AC (AC-L10) 1-475-617-21 SWITCH BLOCK, CONTROL (FK-8500) 1-569-008-21 ADAPTOR, CONVERSION 2P (TRV43/TRV46/TRV46PK) (TR315/TR416:BR/TR416PK/TR516PK/TRV16:E,BR,HK,TW/TRV16PK/...
Page 176 Take a copy CAMERA COLOR REPRODUCTION FRAME and Parts reference sheets with a clear sheet for use. FOR CAMERA COLOR REPRODUCTION ADJUSTMENT CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK < PARTS REFERENCE SHEET > You can find the parts position of mount locations applying to boards of a set.
Page 177 CCD-TR315/TR416/TR416PK/TR516/TR516PK/TR716 CCD-TRV16/TRV16PK/TRV36/TRV36PK/TRV43/TRV46/TRV46PK Sony Corporation 98L0931-1 Printed in Japan © 1998. 12 9-974-124-11 Personal A&V Products Company Published by Quality Engineering Dept.

This manual is also suitable for:

Ccd-tr315 Ccd-tr416 Ccd-tr416pk Ccd-tr516 Ccd-tr516pk Ccd-tr716 ... Show all

Sony CCD TRV16 - Hi8 Handycam Camcorder Service Manual

Service Note

Self-Diagnosis Function

General

Disassembly

Adjustments

Repair Parts List

Quick Links

Related Manuals for Sony CCD TRV16 - Hi8 Handycam Camcorder

Summary of Contents for Sony CCD TRV16 - Hi8 Handycam Camcorder

This manual is also suitable for:

Table of Contents