Panasonic KX-NS1000 User Manual page 265
Pure ip-pbx
Hide thumbs
Also See for KX-NS1000:
- Pc programming manual (1294 pages) ,
- Programming manual (1182 pages) ,
- Manual (542 pages)
Table of Contents
Advertisement
® 9.7 PBX Configuration—[1-1] Configuration—Slot—UM Port Property—
•
Initially, up to 2 hours of voice messages can be recorded. However, installing KX-NSU001 (Activation Key
for Recording Time Expansion) extends this limit to 15 hours. The recording limit can also be increased by
installing a higher capacity Storage Memory Card.
•
When hunting for an available UM port, the PBX ignores any FWD or DND settings (® 2.3 Call Forwarding
(FWD)/Do Not Disturb (DND) Features) applied to the ports.
It is possible to call a port in a UM group directly. If a call is routed directly to a port in the group, it is possible
to apply certain features (e.g., FWD) to that port.
•
It is programmable whether the calls queue when all ports in the group are busy through system
programming. If the queuing is disabled through system programming, the call will be redirected to the
destination, assigned on the trunk group which receives the call, by the Intercept Routing feature.
•
One-look Networking (® 4.2 One-look Networking)
–
In a One-look network, a UM port on the Master unit counts as 10 extensions. (This is because the
Master unit must devote resources to managing various PBX services.) The total number of extensions
available at the Master unit decreases accordingly for each UM port.
For example, if the Master unit has 10 Unified Messaging ports, the maximum number of extensions
becomes:
640 (default maximum) – (10
This limitation does not apply to Slave units or to stand-alone units.
–
UM ports cannot be assigned to another PBX's UM group.
–
A UM group number is automatically assigned to Slave units.
–
A maximum of 16 groups (one per PBX) can exist in a One-look network.
–
A UM group at another PBX can be specified for each UM group as a failover UM group: When a UM
group is offline (e.g., its PBX is not connected to the network), calls routed to that group will be
redirected to the failover UM group. (® 4.2.3.3 UM Group Failover)
•
DSP Resource Usage
Connecting to the Unified Messaging system (including using features such as Two-way Recording)
requires a certain number of DSP resources. If all DSP resources are in use, this operation cannot be
performed. To ensure a minimum level of performance, DSP resources can be reserved for Unified
Messaging operations. (® 5.5.4 DSP Resource Usage)
Notice
Reserving resources for Two-way Recording (® 3.2.1.4 Automatic Two-way Recording for Manager,
® 3.2.2.34 Two-way Record/Two-way Transfer) reserves the necessary number of UM ports
exclusively for Two-way Recording. For example, if 2 UM ports (the default) are available and you
reserve resources for 2 Two-way Recording sessions, both UM ports will be reserved for Two-way
Recording, and the Unified Messaging system will not be available for other uses.
Two-way Recording
UM
Port 1
Reserved (Two-way)
To provide access to the Unified Messaging system in this case, either the number of UM ports must
be increased or the number of resources reserved for Two-way Recording must be lowered.
•
Installing KX-NSU102 or KX-NSU104 (Unified Messaging Activation Key) increases the number of
available UM ports at a PBX (maximum: 24). In a One-look network, these keys are required at each PBX
whose number of UM ports is to be increased.
´ 10) = 540
Incoming Call
UM
Port 2
Reserved (Two-way)
UM Group
3.1.1 Unified Messaging System Overview
Extension Number
Feature Guide
265
Advertisement
Table of Contents
