Yamaha stagepas 500 Owner's Manual

Portable pa system

Hide thumbs Also See for stagepas 500:

User manual

Service manual (72 pages)

Owner's manual (4 pages)

page of 2

/ 2
Bookmarks

Quick Links

Download this manual See also: Service Manual

Enlarged version

Owne r's Ma nu al

Introduction

Thank you for your purchase of the Yamaha PORTABLE PA SYSTEM STAGEPAS 500. The STAGEPAS 500 is a

versatile, compact PA system consisting of two speakers and a mixer.

In order to get the most out of your new STAGEPAS 500 and its sophisticated functions, we suggest you read

through this manual thoroughly. Also keep it in a safe place for future reference.

Features

•

Two-way, 10-inch (25 cm) speaker system

The built-in speakers deliver high-quality powerful sound from an exceptionally compact cabinet.

The scratch-resistant speakers are rugged enough for outdoor use.

•

Powered mixer

The powered mixer is a convenient, high-performance all-in-one unit that includes EQ and reverb. With four

monaural inputs and three stereo inputs, the STAGEPAS 500 can be connected to a wide range of

instruments and devices.

•

Convenient storage

The STAGEPAS 500 can be used in even the most cramped quarters, inside or outside, since the mixer is

built into one of the speaker cabinets. The other speaker has a special compartment for storing speaker

cables and microphones, letting you put all you need for your performance in one convenient place.

Package Contents

Two speakers (500S), mixer, panel, power cord, two speaker cables, Owner's Manual (this booklet)

NOTE:

The mixer and the panel are installed in the speakers when the STAGEPAS 500 leaves the factory.

Before turning on the mixer

Remove the mixer

Be sure that the mixer's power switch is turned off.

Use a screwdriver or coin to turn each screw on the mixer from LOCK to

OPEN until it clicks.

LOCK

OPEN

LOCK

OPEN

Securely hold the mixer's handles to remove it from the speaker.

Use only the mixer's handles when removing the mixer from the speaker and when carrying the mixer

Caution

separate from the speaker.

NOTE:

The mixer can also be used when installed in the speaker.

When you install the mixer into the speaker, make sure to match the indentations on the speaker cabinet to

the corresponding parts on the mixer, and then turn each screw from OPEN to LOCK until it clicks.

Turning the power on/off

Be sure that the mixer's power switch is turned off.

Connect the included power cord to the [AC IN] jack, and plug the power

cord into a power outlet.

• To avoid any loud, unexpected noise from the speakers, first turn on the power to those connected devices

that are closest to the sound source.

Caution

Example: Sound source (CD player or instrument) → STAGEPAS 500

When turning off the power to the system, reverse the order described above.

• Before turning on the power, set the LEVEL controls and MASTER LEVEL control to their minimum setting (zero).

Press the mixer's power switch to the ON position.

The POWER indicator lights.

To turn the power off, press the power switch to the OFF position.

The POWER indicator turns off.

Troubleshooting

500

Power does not turn on

• Is the included power cord correctly connected to a power outlet?

Power shuts down suddenly

• Is the vent on the top panel of the mixer blocked? Since inadequate ventilation can result in overheating the

mixer, the power may be turned off automatically and the mixer may reset itself.

• Is the LIMITER flashes continuously? If the internal power amplifier section is excessively overloaded, the

power may be turned off automatically and the mixer may reset itself.

No sound is heard

• Are external instruments (including a microphone) or speakers correctly connected to the mixer?

• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?

• Are the SPEAKERS L/R jacks connected to the included speakers (500S)?

• Are the included speaker cables used?

If the connector of a speaker cable other than the included speaker cable touches any metal parts such as

the mixer's handle, no sound may result because of a short circuit.

Use only the speaker cables included with the device.

• Is the POWER indicator flashing? There may be a short in the speaker cable or the connection may be

faulty. Check that the speaker cable is correctly connected to the mixer and reapply the power.

• If sound is not still output, contact your Yamaha dealer.

Sound is distorted or noise is produced

• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?

• Are the MIC/LINE switches of each channels set appropriately?

• Are both XLR type and phone type jacks on channels 1–4 being used (connected) at the same time?

Please connect to only one of these jacks on each channel.

• Is the input signal from the connected device set to an appropriate level?

• Use channels 1 or 2, and set the LIMIT/COMP switches to COMP (

preventing distortion.

Sound is not loud enough

• Are the LEVEL controls of all relevant channels and/or the MASTER LEVEL control set to appropriate levels?

• Are the MIC/LINE switches of each channels set appropriately?

OPEN

• Are both XLR type and phone type jacks on channels 1–4 being used (connected) at the same time?

Please connect to only one of these jacks on each channel.

• Is the input signal from the connected device set to an appropriate level?

OPEN

• Is the PHANTOM switch set to ON when using a condenser microphone?

Reverb is not applied to the sound

• Are the REVERB switches of each channels set to ON (

• Is the REVERB control set to an appropriate level?

Changing the sound quality

• Are the Equalizer controls (HIGH/LOW) set to appropriate levels?

• If you want to get a more powerful sound from the speakers, set the SPEECH/MUSIC switch to MUSIC (

• If you want to get a clearer sound for announcements, set the SPEECH/MUSIC switch to SPEECH (

Using a single speaker

• You can use a single speaker. If you use a single speaker, the mixer outputs just one channel of the stereo

signal, left or right.

Outputting the signal for monitoring

• Connect a powered speaker to the MONITOR OUT jack. The MONITOR OUT jack outputs the signal prior

to routing through the MASTER LEVEL control. Adjust the level of output signal from the MONITOR OUT

jack with the MONITOR OUT control. The MONITOR OUT control does not affect the MASTER LEVEL

control. If only the L (left) MONITOR OUT jack is used, the mixer mixes the left and right signals and sends

them to the jack.

Convenient built-in storage compartment

The STAGEPAS 500 features a convenient storage compartment in the speaker box for packing the included

power cable, speaker cable, Owner's Manual (this booklet), and an optional microphone and the cable, as

shown above. Remove the rear panel of the speaker and put in the things you need. Carry the STAGEPAS

500 with you, and you've got all you need to set up and perform—anywhere, anytime.

CAUT I ON

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The above warning is located on the bottom

of the mixer and the rear of the speakers.

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Power supply/Power cord

• Only use the voltage specified as correct for the device. The required

voltage is printed on the name plate of the device.

• Use only the included power cord.

). Compression may be effective in

• Do not place the power cord near heat sources such as heaters or

radiators, and do not excessively bend or otherwise damage the cord,

place heavy objects on it, or place it in a position where anyone could

walk on, trip over, or roll anything over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

Do not open

• Do not open the device or attempt to disassemble the internal parts or

modify them in any way. The device contains no user-serviceable parts.

If it should appear to be malfunctioning, discontinue use immediately and

have it inspected by qualified Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

Power supply/Power cord

• Remove the electric plug from the outlet when the device is not to be used

for extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

Location

• When transporting or moving the device, always use two or more people.

Attempting to lift the device by yourself may damage your back, result in

other injury, or cause damage to the device itself.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn

off the power switch and disconnect the plug from the outlet.

• Do not use the device in a confined, poorly-ventilated location. Make sure

that there is adequate space between the mixer and surrounding walls or

other devices: at least 30 cm at the sides, 30 cm behind and 30 cm

above. If the mixer is to be used installed into the speaker cabinet, make

sure to allow adequate space between the speaker and the surrounding

walls or other devices: at least 30 cm at the sides, 30 cm behind and 30

cm above. Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), or even fire.

• Do not use the speaker's handles for suspended installation. Doing so

can result in damage or injury.

• Avoid setting all equalizer controls and faders to their maximum.

Depending on the condition of the connected devices, doing so may

cause feedback and may damage the speakers.

• Do not expose the device to excessive dust or vibrations, or extreme cold

or heat (such as in direct sunlight, near a heater, or in a car during the

day) to prevent the possibility of panel disfiguration or damage to the

internal components.

• Do not place the device in an unstable position where it might

accidentally fall over.

• Do not block the vents. This mixer has ventilation holes at the top to

prevent the internal temperature from becoming too high. In particular, do

not place the device on its side or upside down. Inadequate ventilation

can result in overheating, possibly causing damage to the device(s), or

even fire.

• Do not use the device in the vicinity of a TV, radio, stereo equipment,

mobile phone, or other electric devices. Doing so may result in noise,

both in the device itself and in the TV or radio next to it.

Connections

• Before connecting the device to other devices, turn off the power for all

devices. Before turning the power on or off for all devices, set all volume

levels to minimum.

• For the SPEAKERS jacks, Use only the included speakers (500S) and

speaker cables. Use of other types of speakers and cables may result in

damage to the device(s), or even fire.

Explanation of Graphical Symbols

Dimensions

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the

presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

Speaker

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the product.

10 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or table specified

by the manufacturer, or sold with the apparatus. When a cart is

used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when unused

for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Specifications

(98-6500)

General Specifications

Maximum Output Power

PRECAUTIONS

250 W + 250 W (±10 %)/4Ω @ 10 % THD at 1 kHz (SPEAKERS L/R)

200 W + 200 W/4Ω @ 1 % THD at 1 kHz (SPEAKERS L/R)

Maximum Output Level

116 dB (1 m)

Frequency Response (Nomimal output level @ 1 kHz)

-3 dB, 0 dB, +1 dB @ 20 Hz-20 kHz (MUSIC/SPEECH=MUSIC) (MONITOR OUT)

-3 dB, 0 dB, +1 dB @ 80 Hz-20 kHz (MUSIC/SPEECH = SPEECH) (REC OUT)

-3dB, 0dB, +1 dB @ 20 Hz-20 kHz, 1 W Output (MUSIC/SPEECH=MUSIC, without Speaker

EQ) (SPEAKERS L/R)

Total Harmonic Distortion

0.5 % @ 20 Hz, 1 kHz, 20 kHz +14 dBu GAIN= nominal (MONITOR OUT, REC OUT)

Hum & Noise (Equivalent Input Noise, Rs = 150Ω, MIC/LINE = MIC)

Water warning

-106 dBu (CH1/2)

• Do not expose the device to rain, use it near water or in damp or wet

-112 dBu (CH3/4)

-65 dBu Residual output noise (SPEAKERS L/R)

conditions, or place containers on it containing liquids which might spill

into any openings.

Crosstalk (1 kHz)

-70 dB between input channels

• Never insert or remove an electric plug with wet hands.

Phantom Voltage

+15 V (CH1-4)

If you notice any abnormality

• If the power cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the device, or if any unusual smells

or smoke should appear to be caused by it, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualified Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualified Yamaha service personnel.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

Handling caution

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance with the following

• When turning on the AC power in your audio system, always turn on the

code:

device LAST, to avoid speaker damage. When turning the power off, the

device should be turned off FIRST for the same reason.

• Do not insert your fingers or hands in any gaps or openings on the device

• This applies only to products distributed by Yamaha Music U.K. Ltd.

(vents,, ports, etc.).

For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.)

into any gaps or openings on the device (vents, ports, etc.) If this

CANADA

happens, turn off the power immediately and unplug the power cord from

Yamaha Canada Music Ltd.

the AC outlet. Then have the device inspected by qualified Yamaha

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

service personnel.

Tel: 416-298-1311

• Do not use the device for a long period of time at a high or uncomfortable

U.S.A.

Yamaha Corporation of America

volume level, since this can cause permanent hearing loss. If you

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

experience any hearing loss or ringing in the ears, consult a physician.

U.S.A.

Tel: 714-522-9011

• Do not operate the device if the sound is distorting. Prolonged use in this

CENTRAL & SOUTH AMERICA

condition could cause overheating and result in fire.

MEXICO

Yamaha de México S.A. de C.V.

• Do not rest your weight on the device or place heavy objects on it, and

Calz. Javier Rojo Gómez #1149,

avoid use excessive force on the buttons, switches or connectors.

Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Protective Circuit (poly switch)

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,

All full-range loudspeakers are fitted with a self-resetting poly switch that

CEP 04534-013 Sao Paulo, SP. BRAZIL

protects the high-frequency driver from damage caused by excessive

Tel: 011-3704-1377

power. If a loudspeaker cabinet loses high-frequency output, immediately

ARGENTINA

Yamaha Music Latin America, S.A.

remove power from the unit and wait for two to three minutes. This should

Sucursal de Argentina

be long enough to allow the poly switch to reset. Reapply power and check

Olga Cossettini 1553, Piso 4 Norte

Madero Este-C1107CEK

the performance of the high frequency driver before continuing, with the

Buenos Aires, Argentina

Tel: 011-4119-7000

power reduced to a level that does not cause the poly switch to interrupt

PANAMA AND OTHER LATIN

the signal.

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Interference From Cell Phones

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Using a cell phone near the speaker system can induce noise. If this occurs,

Tel: +507-269-5311

move the cell phone further away from the speaker system.

THE UNITED KINGDOM

Yamaha Music U.K. Ltd.

Air blowing out of the bass reflex ports is normal, and often occurs when the

Sherbourne Drive, Tilbrook, Milton Keynes,

speaker is handling program material with heavy bass content.

MK7 8BL, England

Tel: 01908-366700

GERMANY

Yamaha Music Europe GmbH

Yamaha cannot be held responsible for damage caused by improper use

Siemensstrasse 22-34, 25462 Rellingen, Germany

or modifications to the device.

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH

Branch Switzerland in Zürich

Always turn the power off when the device is not in use.

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

The performance of components with moving contacts, such as switches,

AUSTRIA

Yamaha Music Europe GmbH Branch Austria

volume controls, and connectors, deteriorates over time. Consult qualified

Schleiergasse 20, A-1100 Wien, Austria

Yamaha service personnel about replacing defective components.

Tel: 01-60203900

(5)-3

CZECH REPUBLIC/SLOVAKIA/

HUNGARY/SLOVENIA

Yamaha Music Europe GmbH Branch Austria

IMPORTANT

Schleiergasse 20, A-1100 Wien, Austria

Please record the serial number of this unit in the space below.

Tel: 01-602039025

Model:

Serial No.:

The serial number is located on the bottom or rear of the unit.

Retain this Owner's Manual in a safe place for future reference.

Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/

Yamaha Manual Library:

Mixer

LOCK

OPEN

POWER

OFF

AC IN

175

342

298

120

Tripod pole diameter 35-36

2-M8 x 25

* Use of the stand should refer to stand manufacturer's instructions.

Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at

any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

LIMIT/COMP switch

ON = Comp, OFF = Limit (CH1/2)

Power Consumption

65 W

Weight

24 kg (Speaker x 2 + Powered Mixer)

Stereo Input Channel Equalization

±15 dB

HIGH 10 kHz shelving

LOW 100 Hz shelving

Speakers (500S)

Enclosure

2 way bass-reflex type, Polypropylene, Black

Crossover Frequency

4.0 kHz (LF: 12 dB/oct, HF: 12 dB/oct)

Frequency Range

55 Hz-20 kHz (-10 dB)

Speaker Unit

LF: 10" (25 cm) Cone

HF: 1" (2.54cm) Compression Driver

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!This product, when installed as

does not guarantee that interference will not occur in all installations. If this product is

indicated in the instructions contained in this manual, meets FCC requirements.

found to be the source of interference, which can be determined by turning the unit

Modifications not expressly approved by Yamaha may void your authority, granted by

"OFF" and "ON", please try to eliminate the problem by using one of the following

the FCC, to use the product.

measures:Relocate either this product or the device that is being affected by the

interference.

IMPORTANT: When connecting this product to accessories and/or another product

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or

use only high quality shielded cables. Cable/s supplied with this product MUST be

install AC line filter/s.

used. Follow all installation instructions. Failure to follow instructions could void your

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna

FCC authorization to use this product in the USA.

lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.

NOTE: This product has been tested and found to comply with the requirements listed

If these corrective measures do not produce satisfactory results, please contact the

in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these

local retailer authorized to distribute this type of product. If you can not locate the

requirements provides a reasonable level of assurance that your use of this product in

appropriate retailer, please contact Yamaha Corporation of America, Electronic Service

a residential environment will not result in harmful interference with other electronic

Division, 6600 Orangethorpe Ave, Buena Park, CA90620

devices. This equipment generates/uses radio frequencies and, if not installed and

The above statements apply ONLY to those products distributed by Yamaha

used according to the instructions found in the users manual, may cause interference

Corporation of America or its subsidiaries.

harmful to the operation of other electronic devices. Compliance with FCC regulations

As the colours of the wires in the mains lead of this apparatus may not correspond with the

IMPORTANT NOTICE FOR THE UNITED KINGDOM

coloured markings identifying the terminals in your plug proceed as follows:

Connecting the Plug and Cord

The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug

which is marked by the letter E or by the safety earth symbol

or colored GREEN or

GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured BLACK.

GREEN-AND-YELLOW : EARTH

The wire which is coloured BROWN must be connected to the terminal which is marked with the

BLUE

: NEUTRAL

letter L or coloured RED.

BROWN

: LIVE

NORTH AMERICA

POLAND

ASIA

Yamaha Music Europe GmbH

THE PEOPLE'S REPUBLIC OF CHINA

Branch Sp.z o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland

Yamaha Music & Electronics (China) Co.,Ltd.

Tel: 022-868-07-57

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

THE NETHERLANDS/

Tel: 021-6247-2211

BELGIUM/LUXEMBOURG

INDIA

Yamaha Music Europe Branch Benelux

Yamaha Music India Pvt. Ltd.

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

5F Ambience Corporate Tower Ambience Mall Complex

Tel: 0347-358 040

Ambience Island, NH-8, Gurgaon-122001, Haryana, India

FRANCE

Tel: 0124-466-5551

Yamaha Musique France

INDONESIA

BP 70-77312 Marne-la-Vallée Cedex 2, France

PT. Yamaha Music Indonesia (Distributor)

Tel: 01-64-61-4000

PT. Nusantik

ITALY

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Yamaha Musica Italia S.P.A.

Tel: 21-520-2577

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

KOREA

Tel: 02-935-771

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,

SPAIN/PORTUGAL

Kangnam-Gu, Seoul, Korea

Yamaha Música Ibérica, S.A.

Tel: 080-004-0022

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

MALAYSIA

Tel: 91-639-8888

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

SWEDEN

Petaling Jaya, Selangor, Malaysia

Yamaha Scandinavia AB

Tel: 3-78030900

J. A. Wettergrens Gata 1, Box 30053

SINGAPORE

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building

DENMARK

140 Paya Lebor Road, Singapore 409015

YS Copenhagen Liaison Office

Tel: 747-4374

Generatorvej 6A, DK-2730 Herlev, Denmark

TAIWAN

Tel: 44 92 49 00

Yamaha KHS Music Co., Ltd.

NORWAY

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Norsk filial av Yamaha Scandinavia AB

Taiwan 104, R.O.C.

Grini Næringspark 1, N-1345 Østerås, Norway

Tel: 02-2511-8688

Tel: 67 16 77 70

THAILAND

RUSSIA

Siam Music Yamaha Co., Ltd.

Yamaha Music (Russia)

4, 6, 15 and 16th floor, Siam Motors Building,

Room 37, bld. 7, Kievskaya street, Moscow, 121059,

891/1 Rama 1 Road, Wangmai,

EUROPE

Russia

Pathumwan, Bangkok 10330, Thailand

Tel: 495 626 5005

Tel: 02-215-2626

OTHER ASIAN COUNTRIES

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Yamaha Corporation,

Asia-Pacific Sales & Marketing Group

Siemensstrasse 22-34, 25462 Rellingen, Germany

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Tel: +49-4101-3030

Japan 430-8650

AFRICA

Tel: +81-53-460-2303

Yamaha Corporation,

OCEANIA

Asia-Pacific Sales & Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

AUSTRALIA

Japan 430-8650

Yamaha Music Australia Pty. Ltd.

Tel: +81-53-460-2303

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

MIDDLE EAST

Tel: 3-9693-5111

COUNTRIES AND TRUST

TURKEY/CYPRUS

TERRITORIES IN PACIFIC OCEAN

Yamaha Music Europe GmbH

Yamaha Corporation,

Siemensstrasse 22-34, 25462 Rellingen, Germany

Asia-Pacific Sales & Marketing Group

Tel: 04101-3030

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

OTHER COUNTRIES

Japan 430-8650

Yamaha Music Gulf FZE

Tel: +81-53-460-2303

LOB 16-513, P.O.Box 17328, Jubel Ali,

Dubai, United Arab Emirates

HEAD OFFICE

Tel: +971-4-881-5868

Yamaha Corporation, Pro Audio Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2441

U.R.G., Pro Audio Division

http://www.yamaha.co.jp/manual/

008MW-D0 Printed in China

Unit: mm

111.5

(class B)

(3 wires)

PA26'

Summary of Contents for Yamaha stagepas 500

Page 1 WARNING Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at If the connector of a speaker cable other than the included speaker cable touches any metal parts such as Specifications TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
Page 2 Controls and Functions Controls and Functions Controls and Functions The STAGEPAS 500 can be used in a wide variety of sound reinforcement applications, from a full-band Getting sound out of the system Channel input jacks (CH 1 to 4) performance onstage to solo street performance—providing a powerful, high-performance system in an For connecting a guitar, microphone, keyboard or other instrument/device.

Yamaha stagepas 500 Owner's Manual

Quick Links

Related Manuals for Yamaha stagepas 500

Summary of Contents for Yamaha stagepas 500