General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
Page 12
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: –...
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.
Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer.
Page 16
Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing.
Page 17
Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
Page 18
Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations.
Page 19
Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing.
Page 20
Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Page 21
Safety notice 8 DANGER Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Laser compliance statement Some models of ThinkPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S.
Page 23
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.
Page 24
ThinkPad X200 and X200s Hardware Maintenance Manual...
“Important information about replacing RoHS compliant FRUs” on page 21 Important: BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site http://www.lenovo.com/support System Disassembly/Reassembly videos that show the FRU removals or ®...
v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one.
MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). Custom Model Variant (CMV) This is a unique configuration that has been negotiated between IBM or Lenovo and the customer. A unique 4-digit MT and 3-digit model is provided to the customer to place orders (Example: 1829-W15).
Page 28
(this is the same record found in PEW). v eSupport can be accessed at the following Web site: http://www.lenovo.com/ support v To view the key commodities, click on PARTS INFORMATION, then PARTS LOOKUP.
FRU part numbers. Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo’s requirements and schedule in the EU. Products sold in 2005 and 2006, will contain some RoHS compliant FRUs.
Page 30
ThinkPad X200 and X200s Hardware Maintenance Manual...
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of servicer __ 2. Date of service __ 3.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses.
PC-Doctor. This section is an overview of the procedure. For details that depend on model-unique functions, refer to “ThinkPad X200 and X200s” on page 47. Note: PC-Doctor for DOS is available at following Web site: http://www.lenovo.com/ support To create the PC-Doctor diagnostic diskette, follow the instruction on the Web site.
Page 35
Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names may appear in the PC-Doctor menu. Diagnostics Interactive Tests Hardware Info Utility Quit F1=Help Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Serial Ports Parallel Ports Fixed Disks Diskette Drives...
Select one of the categories listed below to display symptoms and solutions: v Check System Health v System and Device Tests v Lenovo Troubleshooting Center v System Reports v Updates and Support PC-Doctor for Rescue and Recovery ®...
Power system checkout To verify a symptom, do the following: 1. Turn off the computer. 2. Remove the battery pack. 3. Connect the ac adapter. 4. Check that power is supplied when you turn on the computer. 5. Turn off the computer. 6.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 63). 4. Remove the backup battery (see “1060 Backup battery” on page 76). 5.
Page 40
ThinkPad X200 and X200s Hardware Maintenance Manual...
Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.com/spm Restoring the factory contents by using Product Recovery discs When the hard disk drive (HDD) or solid state drive (SSD) is replaced because of a failure, no Product Recovery program is on the new drive.
If it has, it can be used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenovo authorized servicers provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive.
Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made available to the servicer, neither Lenovo nor Lenovo authorized servicers provide any services to reset the user HDPs or to recover data from the hard disk drive.
Page 44
Note: To check whether the ThinkPad computer supports the Passphrase function, enter the BIOS Setup Utility and go to Security --> Password. If Using Passphrase item is displayed in the menu, this function is available on the ThinkPad computer. 3. Select Security, using the cursor directional keys to move down the menu. 4.
Power management To reduce power consumption, the computer has three power management modes: screen blank, standby, and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. ®...
v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters standby mode. Wait a few seconds before taking any action to reenter operation mode.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 43 v “Beep symptoms” on page 44 v “No-beep symptoms” on page 44 v “LCD-related symptoms” on page 45 v “Intermittent problems” on page 46 v “Undetermined problems”...
Page 48
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 System board. EAIA data access error—The access to EEPROM is failed. 0188 System board. Invalid RFID Serialization Information Area. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct.
Page 49
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0250 1. Charge the backup battery for more System battery error—System battery is than 8 hours by connecting the ac dead. adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
Page 50
Warning: Your internal hard disk drive customer:If in the primary bay the customer (HDD) may not function correctly on this is using a non-IBM or non-Lenovo hard disk system. Ensure that your HDD is supported drive (HDD), or an old generation IBM...
Error messages Table 2. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility.
Beep symptoms Table 3. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or 1. Reseat the LCD connector. flashing LCD. 2. LCD assembly. 3. External CRT. 4. System board. One long and two short beeps, and a blank 1.
QXGA Notes: v Lenovo will not provide replacement if the LCD is within specification as we cannot guarantee that any replacement LCD will have zero pixel defects. v A bright dot means a pixel is always on (white or color.) v A dark dot means a pixel is always off (black color.)
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs.
Specifications The following table lists the specifications of the ThinkPad X200 and X200s : Table 7. Specifications Feature Description ® ™ Processor v Intel Core 2 Duo processor P8400 (2.26 GHz), 3-MB L2 cache v Intel Core 2 Duo processor P8600 (2.4 GHz), 3-MB L2 cache v Intel Core 2 Duo processor T9400 (2.53 GHz), 6-MB L2 cache...
Page 57
Table 7. Specifications (continued) Feature Description Serial Ultrabay Slim device Supported in ThinkPad X200 UltraBase v DVD drive, 9.5 mm high v DVD/CD-RW combo drive, 9.5 mm high v DVD-RAM/RW drive, 9.5 mm high v Blu-ray disc drive, 9.5 mm high Fingerprint reader Some models I/O port (ThinkPad X200 or...
Status indicators The system status indicators show the status of the computer, as follows: Table 8. Status indicators Indicator Meaning Standby status Green: The computer is in standby mode. Blinking green: The computer is entering standby mode or hibernation mode, or is resuming normal operation. AC power Green: The computer is connected to the ac power supply.
Page 59
Table 8. Status indicators (continued) Indicator Meaning Battery status Green: The battery is charged between 80% to 100% of the capacity, and being discharged between 0% to 80% of the capacity. Blinking green: The battery is charged between 20% to 80% of the capacity, and being charged.
FRU tests The following table shows the test for each FRU. Table 9. FRU tests Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the ThinkPad X200 UltraBase is attached to the ThinkPad computer, detach it. Place the computer on a horizontal surface, and run Diagnostics -->...
Page 61
Table 9. FRU tests (continued) Applicable test DVD drive or 1. Diagnostics --> Other Devices--> Optical Drive DVD/CD-RW combo 2. Interactive Tests --> Optical Drive Test drive Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics -->...
Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 10. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock the computer. Fn+F3 Select a power scheme that has been created by Power Manager. When you press this combination, a panel for selecting a power scheme appears.
Page 63
Table 10. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings.
Page 64
Table 10. Fn key combinations (continued) Key combination Description Fn+cursor keys These key combinations work with Windows Windows Media Player. Fn+down arrow key works for the Play or Pause button, Fn+up arrow key for the Stop button, Fn+right arrow key for the Next Track button, and Fn+left arrow key for the Previous Track button.
FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 60 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components.
Page 67
When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written.
Page 68
Reading or writing the ECA information Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board. The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application.
Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts.
Before servicing ThinkPad X200 and X200s Removing the SIM card: Some models of the ThinkPad X200 and X200s you are servicing might have the SIM card that the customer has been installed. If the computer you are servicing has the SIM card, remove it before you start the servicing.
1010 Battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Table 11. Removal steps of battery pack Unlock the battery release lever 1 . Holding the battery release lever in the unlocked position 2 , remove the battery pack in the direction shown by arrow When installing: Install the battery pack along the slide rails of the slot.
1020 Hard disk drive (HDD) cover, HDD, and HDD rubber rails or solid state drive (SSD) and storage converter For access, remove this FRU: v “1010 Battery pack” on page 63 Attention: v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock.
Page 73
Table 12. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) When installing: Make sure that the HDD connector or SSD connector is attached firmly. ThinkPad X200 and X200s...
Page 74
Table 12. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) HDD and HDD rubber rails: When installing: The rubber rails on the hard disk drive must be attached to the replacement drive. Otherwise the drive cannot be installed properly. SSD and storage converter: ThinkPad X200 and X200s Hardware Maintenance Manual...
Page 75
Table 12. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) When installing: When you install the SSD in the storage converter, do as follows. ThinkPad X200 and X200s...
1030 DIMM For access, remove this FRU in order: v “1010 Battery pack” on page 63 Table 13. Removal steps of dimm Remove the DIMM slot cover as shown in this figure. Note: Loosen the screws 1 , but do not remove them. ThinkPad X200 and X200s Hardware Maintenance Manual...
Page 77
Table 13. Removal steps of dimm (continued) Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place.
1040 Keyboard For access, remove this FRU in order: v “1010 Battery pack” on page 63 Table 14. Removal steps of keyboard Step Icon Screw (quantity) Color Torque M2 × 5 mm, wafer-head, Black 0.181 Nm nylon-coated (4) (1.85 kgfcm) ThinkPad X200 and X200s Hardware Maintenance Manual...
Page 79
Table 14. Removal steps of keyboard (continued) Lift the keyboard a little in the direction shown by arrow 4 , and then detach the connector 5 . ThinkPad X200 and X200s...
Page 80
Table 14. Removal steps of keyboard (continued) When installing: 1. Attach the keyboard connector firmly. 2. Make sure that the keyboard edges are under the frame as shown in this figure. Then press the keys to latch the keyboard firmly in place. 3.
1050 Palm rest or palm rest with fingerprint reader For access, remove this FRU in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU.
Page 82
Table 15. Removal steps of palm rest (continued) Note: Step 2 is only for models with the fingerprint reader. For models without the fingerprint reader, skip step 2 . ThinkPad X200 and X200s Hardware Maintenance Manual...
Page 83
Table 15. Removal steps of palm rest (continued) When installing: 1. In models with the fingerprint reader, attach the fingerprint reader connector firmly to the system board. 2. Press the left and right top edges of the palm rest to fit it into place. 3.
1060 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 v “1050 Palm rest or palm rest with fingerprint reader”...
Page 85
Table 16. Removal steps of backup battery (continued) When installing: Make sure that the battery connector is attached firmly. ThinkPad X200 and X200s...
1070 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 v “1050 Palm rest or palm rest with fingerprint reader” on page 73 Table 17.
Page 87
Table 17. Removal steps of PCI Express Mini Card for wireless LAN (continued) When installing: v In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN on the card, and the black cable into the jack labeled AUX.
Page 88
Table 17. Removal steps of PCI Express Mini Card for wireless LAN (continued) Harf size PCI Express Mini Card: In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Page 89
Table 17. Removal steps of PCI Express Mini Card for wireless LAN (continued) When installing: v Plug the gray cable into the jack labeled MAIN on the card, and the black cable into the jack labeled AUX. ThinkPad X200 and X200s...
1080 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 v “1050 Palm rest or palm rest with fingerprint reader” on page 73 Table 18.
Page 91
Table 18. Removal steps of PCI Express Mini Card for wireless WAN (continued) When installing: Plug the red cable into the jack labeled MAIN on the card, and the blue cable into the jack labeled AUX. ThinkPad X200 and X200s...
1090 Intel Turbo Memory Minicard or wireless USB adapter For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 v “1050 Palm rest or palm rest with fingerprint reader” on page 73 Table 19.
Page 93
Table 19. Removal steps of Intel Turbo Memory Minicard or wireless USB adapter (continued) When installing: In models with the wireless USB adapter, plug the yellow cable into the jack on the card. ThinkPad X200 and X200s...
1100 Keyboard bezel For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 v “1050 Palm rest or palm rest with fingerprint reader” on page 73 Table 20. Removal steps of keyboard bezel Step Screw (quantity) Color...
1110 Speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 v “1050 Palm rest or palm rest with fingerprint reader” on page 73 Table 21. Removal steps of speaker assembly When installing: Make sure that the speaker connector is attached firmly.
1120 I/O card assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 v “1050 Palm rest or palm rest with fingerprint reader” on page 73 v “1110 Speaker assembly” on page 87 Table 22.
Page 97
Table 22. Removal steps of I/O card assembly (continued) Note: The cable is secured with a double-faced adhesive tape. Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) Turn the I/O card over, and then disconnect the cable from the flip-lock ZIF connector.
1130 LCD assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 v “1050 Palm rest or palm rest with fingerprint reader” on page 73 v “1070 PCI Express Mini Card for wireless LAN” on page 78 v “1080 PCI Express Mini Card for wireless WAN”...
Page 99
Table 23. Removal steps of LCD assembly (continued) Step Screw (quantity) Color Torque M2 × 5 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) Before step 3 , strip off the tapes securing the antenna cables, and release the cables from the cable guides of the frame.
Page 100
Table 23. Removal steps of LCD assembly (continued) ThinkPad X200 and X200s Hardware Maintenance Manual...
Page 101
Table 23. Removal steps of LCD assembly (continued) When installing: 1. Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
1140 Base cover assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1020 Hard disk drive (HDD) cover, HDD, and HDD rubber rails or solid state drive (SSD) and storage converter” on page 64 v “1030 DIMM”...
Page 103
Table 24. Removal steps of base cover assembly for ThinkPad X200 (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) ThinkPad X200 and X200s...
Page 104
Table 24. Removal steps of base cover assembly for ThinkPad X200 (continued) In step 5 , remove the system board, the DC-in connector, and the fan assembly together from the base cover assembly. When installing: Make sure that the position of the wireless switch, and firmly fit into the frame a .
Page 105
Table 25. Removal steps of base cover assembly for ThinkPad X200s ThinkPad X200s: Remove the top shielding assembly at first. Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) Step Screw (quantity) Color Torque M2 ×...
Page 106
Table 25. Removal steps of base cover assembly for ThinkPad X200s (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (5) Silver 0.181 Nm (1.85 kgfcm) In step 5 , remove the system board, the DC-in connector, and the fan assembly together from the base cover assembly.
Page 107
Applying labels to the base cover: The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: Product label Homologation label Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
1150 Systemboard, DC-in connector, fan, and ExpressCard slot assembly Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.
Page 109
Table 26. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200 ThinkPad X200: Following components soldered on the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. ™...
Page 110
Table 26. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200 (continued) Note: The DC-in connector and the fan assembly are attached to the underside of the system board. Step Screw (quantity) Color Torque M2 ×...
Page 111
Table 26. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200 (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, flat-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure.
Page 112
Table 26. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200 (continued) Note: The ExpressCard slot assembly is attached to the system board. Step Screw (quantity) Color Torque M2 × 3.5 mm, flat-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm)
Page 113
Table 27. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s ThinkPad X200s: Following components soldered on the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. ICH (I/O Controller Hub) MCH (Memory Controller Hub) ™...
Page 114
Table 27. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s (continued) Note: The DC-in connector and the fan assembly are attached to the underside of the system board. When installing: Make sure that the DC-in connector and the fan connector are attached to the system board firmly.
Page 115
Table 27. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s (continued) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component.
Page 116
Table 27. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s (continued) Turn the system board over, and then remove the ExpressCard slot assembly from the system board. ThinkPad X200 and X200s Hardware Maintenance Manual...
2010 LCD front bezel For access, remove this FRU: v “1010 Battery pack” on page 63 Table 28. Removal steps of LCD front bezel for 12.1-in. WXGA LCD model 12.1-in. WXGA LCD model: Step Screw cap Screw (quantity) Color Torque M2.5 ×...
Page 118
Table 29. Removal steps of LCD front bezel for 12.1-in. WXGA+ LCD model 12.1-in. WXGA+ LCD model: Step Screw cap Screw (quantity) Color Torque M2.5 × 4 mm, wafer-head, Black 0.392 Nm wafer-coated (2) (4 kgfcm) M2.5 × 4 mm, wafer-head, Black 0.392 Nm wafer-coated (5)
Page 119
Table 29. Removal steps of LCD front bezel for 12.1-in. WXGA+ LCD model (continued) In step 4 and 5 , detach the claws. Then remove the LCD front bezel. When installing: Make sure that all the claws are attached firmly. ThinkPad X200 and X200s...
2020 Inverter card For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “2010 LCD front bezel” on page 109 Table 30. Removal steps of inverter card Note: 12.1-in. WXGA+ LCD models do not have the inverter card. Step Screw (quantity) Color...
2030 Bluetooth daughter card (BDC-2.1) For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “2010 LCD front bezel” on page 109 Table 31. Removal steps of Bluetooth daughter card When installing: Make sure that the connector 1 is attached firmly. ThinkPad X200 and X200s...
2040 Integrated camera For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “2010 LCD front bezel” on page 109 Table 32. Removal steps of Integrated camera Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) ThinkPad X200 and X200s Hardware Maintenance Manual...
2050 LCD panel, LCD brackets, and LCD cable For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 v “1050 Palm rest or palm rest with fingerprint reader” on page 73 v “1070 PCI Express Mini Card for wireless LAN”...
Page 124
Table 33. Removal steps of LCD panel, LCD brackets, and LCD cable for 12.1-in. WXGA LCD model (continued) Note: Step 3 is only for models without the integrated camera. For models with the integrated camera, skip step 3 . Step Screw (quantity) Color Torque...
Page 125
Table 33. Removal steps of LCD panel, LCD brackets, and LCD cable for 12.1-in. WXGA LCD model (continued) Remove the LCD bracket a . Step Screw (quantity) Color Torque M2 × 2 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) ThinkPad X200 and X200s...
Page 126
Table 33. Removal steps of LCD panel, LCD brackets, and LCD cable for 12.1-in. WXGA LCD model (continued) Turn the LCD panel over, and then remove the LCD cable b from the LCD panel. When installing: Make sure that the LCD cable connector is attached firmly. ThinkPad X200 and X200s Hardware Maintenance Manual...
Page 127
Table 34. Removal steps of LCD panel, LCD brackets, and LCD cable for 12.1-in. WXGA+ LCD model 12.1-in. WXGA+ LCD model: Step Screw (quantity) Color Torque M2 x 2 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) ThinkPad X200 and X200s...
Page 128
Table 34. Removal steps of LCD panel, LCD brackets, and LCD cable for 12.1-in. WXGA+ LCD model (continued) Turn the LCD panel over, and then remove the LCD cable c from the LCD panel. When installing: Make sure that the LCD cable connector is attached firmly. ThinkPad X200 and X200s Hardware Maintenance Manual...
2060 Hinges and hinge brackets For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “2010 LCD front bezel” on page 109 v “2020 Inverter card” on page 112 v “2030 Bluetooth daughter card (BDC-2.1)” on page 113 v “2040 Integrated camera”...
Page 130
Table 36. Removal steps of hinges and hinge brackets for 12.1-in. WXGA+ LCD model 12.1-in. WXGA+ LCD model: In step 1 , release the antenna cables from the cable guides. ThinkPad X200 and X200s Hardware Maintenance Manual...
Page 131
Table 36. Removal steps of hinges and hinge brackets for 12.1-in. WXGA+ LCD model (continued) Remove the hinges a and the hinge brackets b . Step Screw (quantity) Color Torque M2.5 x 4 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) ThinkPad X200 and X200s...
2070 LCD rear cover and wireless antenna cables For access, remove these FRUs in order: v “1010 Battery pack” on page 63 v “1040 Keyboard” on page 70 v “1050 Palm rest or palm rest with fingerprint reader” on page 73 v “1070 PCI Express Mini Card for wireless LAN”...
Page 133
Table 37. Removal steps of LCD rear cover and wireless antenna cables for 12.1-in. WXGA LCD model (continued) In step 3 , release the antenna cables from the cable guides of the rear cover. ThinkPad X200 and X200s...
Page 134
Table 37. Removal steps of LCD rear cover and wireless antenna cables for 12.1-in. WXGA LCD model (continued) Note: Wireless antennas are secured with double-faced adhesive tapes. When installing: When you attache the antenna cables, do as follows. ThinkPad X200 and X200s Hardware Maintenance Manual...
Page 135
Table 37. Removal steps of LCD rear cover and wireless antenna cables for 12.1-in. WXGA LCD model (continued) Cable routing: Place the antenna assembly as shown in this figure. Wireless WAN antenna, AUX (blue) Wireless LAN antenna, AUX (black) Wireless USB antenna (yellow) MIMO antenna (white) Wireless LAN antenna, MAIN (gray) Wireless WAN antenna, MAIN (red)
Page 136
Table 38. Removal steps of LCD rear cover and wireless antenna cables for 12.1-in. WXGA+ LCD model 12.1-in. WXGA+ LCD model: In step 1 , release the antenna cables from the cable guides of the rear cover. Note: Wireless antennas are secured with double-faced adhesive tapes. ThinkPad X200 and X200s Hardware Maintenance Manual...
Page 137
Table 38. Removal steps of LCD rear cover and wireless antenna cables for 12.1-in. WXGA+ LCD model (continued) Cable routing: Place the antenna assembly as shown in this figure. Wireless LAN antenna, AUX (black) Wireless USB antenna (yellow) MIMO antenna (white) Wireless LAN antenna, MAIN (gray) Attention: As you route the antenna cables, make sure that they are not subjected to any tension.
Locations Front view ThinkLight Integrated camera (for some models) Status indicators Note: For the description of each indicator, see “Status indicators” on page Power switch Security keyhole Hard disk drive (HDD) or solid state drive (SSD) RJ-11 (modem) connector Microphone jack Stereo headphone jack Universal serial bus (USB) connector TrackPoint pointing stick...
Rear view ExpressCard slot Wireless radio switch Universal Serial Bus (USB) connector RJ-45 (Ethernet) connector External monitor connector Universal serial bus (USB) connector AC power connector Bluetooth antenna (for some models) Status indicators Note: For the description of each indicator, see “Status indicators” on page ThinkPad X200 and X200s...
Rear view (ThinkPad X200 UltraBase) AC power connector Universal serial bus (USB) connectors External monitor connector DisplayPort connector Headphone jack Microphone jack RJ-45 (Ethernet) connector Security keyhole Security lock key Universal serial bus (USB) connector Serial Ultrabay Slim device release latch Serial Ultrabay Slim device eject lever Serial Ultrabay Slim device Docking connector...
Parts list This section contains following lists of the service parts. v “Overall” on page 136 v “LCD FRUs” on page 161 v “Keyboard” on page 174 v “Miscellaneous parts” on page 175 v “AC adapters” on page 175 v “Power cords” on page 176 v “Recovery discs”...
Overall ThinkPad X200 and X200s Hardware Maintenance Manual...
Page 145
Table 39. Parts list—Overall FRU no. RoHS See “Miscellaneous parts” on page 175. LCD unit (see “LCD FRUs” on page 161.) Keyboard bezel assembly 44C9542 Backup battery 92P1210 Intel Turbo Memory 2-GB Minicard 42T0991 v 7454-CTO, 23x, 25x, 28x, 2Jx, 2Lx, 2Qx v 7455-CTO, 33x, 35x, 3Ax, 3Hx, 3Jx, 3Sx, 3Tx v 7457-CTO, 43x, 44x, 47x, 49x, 4Dx v 7458-CTO, 53x, 54x, 56x, 57x, 58x, 5Ax, 5Bx, 5Cx, 5Dx,...
Page 146
Table 39. Parts list—Overall (continued) FRU no. RoHS System board with Intel Core 2 Duo processor P8400 42W8096 (2.26 GHz), non-AMT, non-TPM v 7454-CTO v 7455-CTO v 7457-CTO v 7458-CTO v 7459-CTO v 2023-CTO v 2024-CTO System board with Intel Core 2 Duo processor P8600 42W8138 (2.4 GHz), AMT, TPM v 7454-CTO...
Page 147
Table 39. Parts list—Overall (continued) FRU no. RoHS System board with Intel Core 2 Duo processor SU9300 44C9667 (1.2 GHz), TPM v 7462-CTO, 4Dx, 4Gx v 7465-CTO, 2Ex, 2Hx v 7466-CTO, 38x, 3Bx v 7469-CTO, 58x, 5Bx v 7470-CTO, 68x, 6Bx v 2046-CTO v 2047-CTO System board with Intel Core 2 Duo processor SU9300...
Page 148
Table 39. Parts list—Overall (continued) FRU no. RoHS System board with Intel Core 2 Duo processor SL9400 44C9669 (1.86 GHz), TPM v 7462-CTO, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Fx, 4Jx, 4Mx, 4Px, 4Rx, 4Tx v 7465-CTO, 28x, 29x, 2Dx, 2Kx, 2Lx, 2Nx, 2Qx, 2Sx, v 7466-CTO, 35x, 3Ax, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Rx, 3Sx v 7469-CTO, 55x, 57x, 5Ax, 5Dx, 5Gx, 5Hx, 5Jx, 5Kx,...
Page 150
Table 39. Parts list—Overall (continued) FRU no. RoHS ® Qualcomm UNDP1 - Wireless WAN card 42T0961 v 7454-CTO v 7455-CTO v 7457-CTO v 7458-CTO, 5Hx, 89x v 7459-CTO v 2023-CTO v 2024-CTO v 7462-CTO v 7465-CTO v 7466-CTO v 7469-CTO v 7470-CTO v 2046-CTO v 2047-CTO...
Page 151
Table 39. Parts list—Overall (continued) FRU no. RoHS Ericsson F3507g Other - Wireless WAN card 43Y6479 v 7454-CTO v 7455-CTO, 3Sx v 7457-CTO v 7458-CTO, 5Mx, 5Px, 5Sx, 5Tx, 7Zx, 85x v 7459-CTO v 2023-CTO v 2024-CTO v 7462-CTO v 7465-CTO v 7466-CTO, 3Rx v 7469-CTO, 5Lx, 5Mx, 5Nx, 5Px, 5Rx, 5Sx, 5Tx, 5Xx, 5Yx, 5Zx, 72x, 73x, 7Lx, 7Mx...
Page 156
Table 39. Parts list—Overall (continued) FRU no. RoHS Battery pack, 9 cell 42T4542 v 7454-CTO v 7455-CTO, 3Ex, 3Qx v 7457-CTO v 7458-CTO, 5Hx, 5Jx, 5Qx, 7Cx, 83x, 88x, 89x v 7459-CTO, 65x, 66x, 6Nx, 6Px, 6Qx, 6Sx, 6Vx, 6Xx v 2023-CTO v 2024-CTO, X3x v 7462-CTO...
Page 157
Table 39. Parts list—Overall (continued) FRU no. RoHS SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm 42T1305 v 7454-CTO, 4Gx v 7455-CTO v 7457-CTO v 7458-CTO v 7459-CTO v 2023-CTO, X2x v 2024-CTO v 7462-CTO v 7465-CTO v 7466-CTO v 7469-CTO, E1x v 7470-CTO, 6Gx, E1x v 2046-CTO, X1x...
Page 158
Table 39. Parts list—Overall (continued) FRU no. RoHS SATA hard disk drive, 160 GB, 9.5 mm, 5,400 rpm OP 42T1501 v 7454-CTO, 25x, 26x, 29x, 2Gx, 2Hx, 2Nx, 2Rx, 2Ux, 2Vx, 2Xx, 2Yx, 92x, 95x, 97x, 98x v 7455-CTO, 35x, 36x, 39x, 3Ax, 3Dx, 3Jx, 3Kx, 3Px v 7457-CTO, 45x, 48x, 49x, 4Ax, 4Bx, 4Hx, 4Lx, 4Mx, 4Px, 4Qx v 7458-CTO, 53x, 55x, 56x, 57x, 5Ax, 5Ex, 5Lx, 5Qx, 69x,...
Page 159
Table 39. Parts list—Overall (continued) FRU no. RoHS SATA hard disk drive, 250 GB, 9.5 mm, 5,400 rpm OP 42T1481 v 7454-CTO, 23x, 28x, 2Lx, 2Tx, 2Wx v 7455-CTO, 33x, 3Cx, 3Lx, 3Mx, 3Sx, 3Tx v 7457-CTO, 44x, 47x, 4Dx, 4Jx, 4Kx, 4Nx v 7458-CTO, 54x, 58x, 5Bx, 5Cx, 5Mx, 5Rx, 5Sx, 77x, 7Fx, 7Hx, 7Nx, 7Sx, 7Tx, 7Xx, 7Yx, 7Zx, 84x v 7459-CTO, 63x, 64x, 6Kx, 6Rx, 6Tx, 6Ux...
Page 160
Table 39. Parts list—Overall (continued) FRU no. RoHS SATA hard disk drive, 250 GB, 9.5 mm, 5,400 rpm 42T1521 v 7454-CTO, 23x, 28x, 2Lx, 2Tx, 2Wx v 7455-CTO, 33x, 3Cx, 3Lx, 3Mx, 3Sx, 3Tx v 7457-CTO, 44x, 47x, 4Dx, 4Jx, 4Kx, 4Nx v 7458-CTO, 54x, 58x, 5Bx, 5Cx, 5Mx, 5Rx, 5Sx, 77x, 7Fx, 7Hx, 7Nx, 7Sx, 7Tx, 7Xx, 7Yx, 7Zx, 84x v 7459-CTO, 63x, 64x, 6Kx, 6Rx, 6Tx, 6Ux...
Page 161
Table 39. Parts list—Overall (continued) FRU no. RoHS SATA hard disk drive, 100 GB, 9.5 mm, 7,200 rpm OP 42T1485 v 7454-CTO, 2Sx, 93x v 7455-CTO, 3Fx, 3Rx v 7457-CTO v 7458-CTO, 7Gx v 7459-CTO v 2023-CTO v 2024-CTO v 7462-CTO v 7465-CTO v 7466-CTO, 3Kx, 3Qx v 7469-CTO...
Page 162
Table 39. Parts list—Overall (continued) FRU no. RoHS SATA hard disk drive, 160 GB, 9.5 mm, 7,200 rpm 42T1439 v 7454-CTO, 2Jx, 2Px, 2Qx, 2Zx, 96x v 7455-CTO, 3Ex, 3Qx v 7457-CTO, 43x v 7458-CTO, 5Dx, 5Fx, 5Hx, 5Jx, 5Nx, 79x, 7Cx, 7Dx, 7Jx, 7Qx, 82x, 87x, 88x v 7459-CTO, 5Fx, 65x, 66x, 6Mx, 6Nx, 6Vx v 2023-CTO...
Page 163
Table 39. Parts list—Overall (continued) FRU no. RoHS SATA solid state drive, 64 GB, 8 mm 42T1898 v 7454-CTO, 24x, 2Kx v 7455-CTO, 34x, 38x v 7457-CTO, 4Cx, 4Ex v 7458-CTO, 72x, 74x v 7459-CTO, 6Ex, 6Gx v 2023-CTO v 2024-CTO v 7462-CTO, 4Gx, 4Hx, 4Jx v 7465-CTO, 2Hx, 2Jx, 2Kx v 7466-CTO, 3Bx, 3Cx, 3Dx...
Page 164
Table 39. Parts list—Overall (continued) FRU no. RoHS DVD drive, 9.5 mm 42T2511 v 7454-CTO v 7455-CTO v 7457-CTO v 7458-CTO v 7459-CTO v 2023-CTO, X2x v 2024-CTO v 7462-CTO v 7465-CTO v 7466-CTO v 7469-CTO v 7470-CTO v 2046-CTO v 2047-CTO DVD/CD-RW combo drive, 9.5 mm 42T2543...
Page 165
Table 39. Parts list—Overall (continued) FRU no. RoHS DVD-RAM/RW drive, 9.5 mm 42T2545 v 7454-CTO, 2Hx, 2Jx, 2Px, 2Qx, 2Zx, 96x, 98x v 7455-CTO, 3Sx, 3Tx v 7457-CTO v 7458-CTO, 5Px, 5Rx, 5Sx, 79x, 7Px, 84x, 86x v 7459-CTO, 66x, 6Mx, 6Nx, 6Qx v 2023-CTO v 2024-CTO v 7462-CTO...
Page 166
Table 39. Parts list—Overall (continued) FRU no. RoHS ThinkPad X200 UltraBase 42X4963 v 7454-CTO, 2Hx, 2Jx, 2Px, 2Qx, 2Zx, 96x, 98x v 7455-CTO, 3Sx, 3Tx v 7457-CTO v 7458-CTO, 5Px, 5Rx, 5Sx, 79x, 7Px, 84x, 86x v 7459-CTO, 66x, 6Mx, 6Nx, 6Px, 6Qx, 6Xx v 2023-CTO, X2x v 2024-CTO, X3x v 7462-CTO...
Page 167
Table 39. Parts list—Overall (continued) FRU no. RoHS Fan assembly, ULV for X200s 45N3236 v 7462-CTO, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx v 7465-CTO, 2Ex, 2Fx, 2Hx, 2Jx, 2Kx v 7466-CTO, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Qx v 7469-CTO, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Gx, 5Hx, 5Jx, 5Kx, 5Ux, 5Wx, 74x, 79x, 7Ax, 7Bx, 7Cx, 7Nx, 7Px v 7470-CTO, 5Gx, 5Hx, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx,...
LCD FRUs In ThinkPad X200 and X200s, there are following types of LCDs. v “12.1-in. WXGA TFT” v “12.1-in. WXGA+ TFT” on page 171 12.1-in. WXGA TFT ThinkPad X200 and X200s...
Page 170
Table 40. Parts list—12.1-in. WXGA TFT FRU no. RoHS LCD bezel assembly 44C9541 v 7454-all v 7455-all v 7457-all v 7458-all v 7459-all v 2023-CTO v 2024-CTO v 7462-CTO, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx v 7465-CTO, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Dx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, v 7466-CTO, 32x, 33x, 34x, 35x, 3Lx, 3Mx, 3Nx, 3Px,...
Page 172
Table 40. Parts list—12.1-in. WXGA TFT (continued) FRU no. RoHS Wireless LAN/WAN/USB antenna kit 44C5394 v 7454-CTO v 7455-CTO v 7457-CTO v 7458-CTO v 7459-CTO v 2023-CTO v 2024-CTO v 7462-CTO, 44x, 45x, 4Cx v 7465-CTO, 2Dx v 7466-CTO v 7469-CTO v 7470-CTO v 2046-CTO v 2047-CTO...
Page 173
Table 40. Parts list—12.1-in. WXGA TFT (continued) FRU no. RoHS LCD rear cover assembly 44C9543 v 7454-all v 7455-all v 7457-all v 7458-all v 7459-all v 2023-CTO v 2024-CTO v 7462-CTO, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx v 7465-CTO, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Dx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx,...
Keyboard Table 42. Parts list—Keyboard Language RoHS Arabic 42T3752 42T3686 Belgian 42T3749 42T3683 Brazilian Portuguese 42T3768 42T3702 Bulgarian 42T4143 42T4139 Canadian French (058) 42T3739 42T3673 Canadian French (Acnor) 42T3738 42T3672 Czech 42T3757 42T3691 Danish 42T3746 42T3680 Dutch 42T3743 42T3677 Finnish, Swedish 42T3744 42T3678 French...
Miscellaneous parts Table 43. Parts list—Miscellaneous parts RoHS Screw kit: 44C9558 Base cover miscellaneous parts kit: 44C9556 v Dummy cover, RJ-11 connector v Knob, Wireless WAN v Knob screw, Wireless WAN v Latch, battery v Latch spring, battery System miscellaneous parts kit: 44C9557 v (a) Top shielding assembly v Holder, Heat sink...
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 45. Parts list—2-pin power cords Region RoHS Argentina 42T5020 42T5105 v models -CTO, xxY Brazil 42T5180 42T5183 v models -CTO, xxP Canada, U.S.
Page 185
Recovery discs Windows XP Professional CDs Windows XP Professional is preinstalled as the operating system in the following models: v 7454-CTO, 2Gx, 2Hx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 92x, 93x, 95x, 96x v 7455-CTO, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx v 7457-CTO, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx v 7458-CTO, 7Rx, 7Sx, 7Tx, 7Ux, 7Vx, 7Wx, 7Xx, 7Yx, 7Zx, 82x, 83x, 84x, 85x, 86x, 87x, 88x, 89x...
Page 186
Table 47. Parts list—Windows XP Professional recovery CDs Language RoHS Arabic 46V1495 Brazilian Portuguese 46V1496 Czech 46V1498 Danish 46V1499 Dutch 46V1510 English 46V1522 English (modem-disabled) 46V1521 Finnish 46V1500 French 46V1501 German 46V1503 Greek 46V1502 Hebrew 46V1504 Hungarian 46V1506 Italian 46V1507 Japanese 46V1508 Korean...
Page 187
Windows Vista Home Basic (32 bit) DVDs Windows Vista Home Basic (32 bit) is preinstalled as the operating system in the following models: v 7454-CTO v 7455-CTO v 7457-CTO, 4Ax, 4Gx v 7458-CTO, 7Ex, 7Fx v 7459-CTO, 6Sx v 2023-CTO v 2024-CTO v 7462-CTO, 42x, 4Kx v 7465-CTO, 23x, 2Xx...
Page 188
Windows Vista Home Premium (32 bit) DVDs Windows Vista Home Premium (32 bit) is preinstalled as the operating system in the following models: v 7454-CTO, 29x v 7455-CTO v 7457-CTO, 48x, 4Bx, 4Hx v 7458-CTO v 7459-CTO v 2023-CTO, X2x v 2024-CTO v 7462-CTO, v 7465-CTO...
Page 189
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 7454-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 2Jx, 2Kx, 2Lx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 97x, 98x v 7455-CTO, 32x, 33x, 34x, 35x, 36x, 38x, 3Ax, 3Dx, 3Ex, 3Fx, 3Hx, 3Jx, 3Sx, 3Tx v 7457-CTO, 42x, 43x, 44x, 45x, 46x, 47x, 49x, 4Cx, 4Dx, 4Ex, 4Jx v 7458-CTO, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx,...
Page 190
Table 50. Parts list—Windows Vista Business (32 bit) DVDs Language RoHS Brazilian Portuguese 46V1167 Czech 46V1172 Danish 46V1170 English 46V1162 English (modem-disabled) 46V2314 French 46V1164 German 46V1165 Greek 46V1177 Hebrew 46V1171 Hungarian 46V1176 Italian 46V1168 Japanese 46V1178 Korean 46V1182 Norwegian 46V1169 Polish 46V1173...
Page 191
Windows Vista Business (64 bit) DVDs Windows Vista Business (64 bit) is preinstalled as the operating system in the following models: v 7454-CTO v 7455-CTO v 7457-CTO v 7458-CTO v 7459-CTO, 6Tx, 6Ux, 6Vx, 6Xx v 2023-CTO v 2024-CTO v 7462-CTO v 7465-CTO v 7466-CTO v 7469-CTO, 7Px...
Page 192
Windows Vista Ultimate (32 bit) DVDs Windows Vista Ultimate (32 bit) is preinstalled as the operating system in the following models: v 7454-CTO v 7455-CTO v 7457-CTO v 7458-CTO, 5Jx, 5Px, 5Tx v 7459-CTO, 66x v 2023-CTO v 2024-CTO, X3x v 7462-CTO v 7465-CTO v 7466-CTO...
USB floppy diskette drive for maintenance diskette 05K9283 USB floppy diskette drive tool kit 27L3452 Test card for integrated Smart Card 42W7820 ThinkPad Hardware Maintenance Diskette Version 1.73 or later — Note: Download the file from the following Web site: http://www.lenovo.com/ ThinkPad X200 and X200s...
Page 194
ThinkPad X200 and X200s Hardware Maintenance Manual...
Actual results may vary. Users of this document should verify the applicable data for their specific environment. Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Active Protection System ®...
Page 198
Part Number: 43Y6632_01 (1P) P/N: 43Y6632_01...