BL-C111A/BL-C131A 1 Warning 1.1. Battery Caution Danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to following caution: Disposal or transportation of lithium batteries should be performed by permitted, in accordance with federal, state and local guidelines.
Page 4
BL-C111A /BL-C131A 1.2.1. Suggested PbF Solder There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper, (Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the manufac- turer’s specific instructions for the melting points of their products and any precautions for using their product with other materi- als.
BL-C111A /BL-C131A SUB BOARD 1.3. For Service Technicians ICs and LSIs are vulnerable to static electricity. When replacing, the following precautions will help to prevent recurring malfunctions. 1. Cover the plastic parts with aluminum foil. 2. Ground the soldering irons. 3.
BL-C111A/BL-C131A 2 Specifications Camera Specifications Items Specifications Zoom 10x (by area) digital zoom Pan/Tilt Angle Pan: -50° to +50°, Tilt: -40° to +10° Number of Pixels 1/6 inch CMOS sensor, 320,000 pixels Illuminance 10-10,000 lx (3-10,000 lx when in Color Night View mode) White Balance Auto/Manual/Hold Lens Brightness...
No. of Images (Saved to PC) 192 x 144 File Size 10 KB 10 KB 7 KB 5 KB No. of Images (Saved to PC) MPEG-4 videos For information about MPEG-4 image capacity, see the Panasonic Network Camera website at http://panasonic.co.jp/pcc/products/en/netwkcam/.
BL-C111A/BL-C131A 3 Features On-site and remote camera monitoring Camera images can be monitored from a PC, both on-site and over the Internet. You can even use your mobile phone to view still images when you’re out of the house. MPEG-4 and Motion JPEG (MJPEG) support Live camera images can be viewed and buffered (i.e., stored in memory) in both MPEG-4 and JPEG (MJPEG) formats, allowing you to select the video format that best suits your needs.
BL-C111A /BL-C131A 4 Technical Descriptions 4.1. Main Board 4.1.1. CPU Block CPU (IC101) Operating Power Supply: 3.3V (for I/O) 1.2V (for Core) Package: 344 pin LGA Outline of Operation: This LSI encodes a picture signal input from a camera into a JPEG or an MPEG4 format and an audio sig- nal input from a microphone into a G726 format, and then it distributes the data to the terminal on the IPV4 or IPV6 network using the network server function achieved by processing the software of a built-in processor.
Page 11
BL-C111A/BL-C131A 4.1.2. LAN Block Consists of IC101 (CPU), IC105 (ETHER-PHY), T1 (Trans) and CN2 (RJ45). T1 (Trans) insulates sets and Ethernet. IC101 (CPU) and IC105 (ETHER-PHY) are connected by a signal called MIIBus which it makes it possible to transmit/receive Ethernet data.
Page 12
BL-C111A /BL-C131A 4.1.4. Power Supply Block Power Supply Block provides power that each block consumes. Input is DC 9V/750mA from AC adaptor. The circuit diagram and output voltage are showed as below.
Page 13
BL-C111A/BL-C131A 4.1.5. Real Time Clock (IC3) Operating Power Supply: 3.3V (3V battery for back up) Package: 8 pin SOP Outline of Operation: Stores Clock Data and resonates 32.768 KHz Clock Signal. Backup Battery provides power when power supply is out. Lithium Battery (BAT1) Output Voltage: 3V Capacity: 220mAh...
Page 14
BL-C111A /BL-C131A 4.1.7. PAN Control Block A pan motor operates, when CPU (IC101) on a Main Board controls the Motor Driver IC (IC402) on the same board. A Constant Voltage Bipolar Drive System is employed. The Voltage of Motor Power (VM) is 3.3V. ø...
Page 15
BL-C111A/BL-C131A 4.1.10. Privacy Mode Control Circuit Privacy Mode is a function to protect privacy so that a lens may be concealed in a cover part by pushing the Privacy Mode switch (SW801) and the picture may not be seen. CPU detects condition of SW801. 4.1.11.
BL-C111A /BL-C131A 4.2. RF Block(C131A only) • Antenna • Receiver The receiving signal from the antenna is input to the RFIC (IC601) after being passed through the Antenna Switch (IC502) and amplified at LNA (Low Noise Amp).The RFIC (IC601) incorporates the LNA (Low Noise Amp), the Mixer for Frequency Converter and the Synthesizer generating the Receiving Local Signal.
・ Though most ISPs (Internet Service Providers) do not yet support IPv6, many local networks already use it. When your ISP supports IPv6, your Panasonic Network Camera will be ready! ・ For more information, visit http://www.ipv6.org/. Note: Refer to the Panasonic Network Camera website at http://panasonic.co.jp/pcc/products/en/netwkcam/ for details about net- work environment.
• If more than 20 minutes have passed since ROM. the selected camera was turned on, you • If you have a Panasonic BB-HGW700A cannot configure the camera. Turn off the Network Camera Control Unit, WEP camera, then turn it on again. This...
Page 23
Internet, we recommend using MJPEG images, and to use audio features. Viewnetcam.com. Viewnetcam.com is a Dynamic DNS service designed for use with Panasonic Network Cameras, and is provided free of charge. For more information about Viewnetcam.com, • The camera image is displayed.
BL-C111A /BL-C131A 8.10. The Inspection After The Repair Inspect the following items after the repair. • Confirm the status (specially MAC Address) refer to Diagnosis NG Check. • PAN/TILT operation • Pyroelectric Infrared Sensor • Video quality 8.11. Diagnosis NG Check When turning on the power, CPU makes a check using the self-diagnosis function.
BL-C111A/BL-C131A 8.12. In Case Where the Main Board Is Replaced and a New MAC Address Label Is Used Rewrite the MAC Address of the RF board 1. Turn on the power after replacing the main board (after a new MAC has been written to the main board). BL-C131A only : Confirm that the WIRELESS/WIRED switch on the bottom of the camera is set to WIRELESS.
BL-C111A /BL-C131A 8.15. How To Change MAC Address Label MAC address label caution When you replace the main board, you must also attach the new MAC address label(included with the main board). Attach the new MAC address label to the unit by placing over the old MAC address label. Make sure the old address cannot be seen. Throw away the old main board.
BL-C111A/BL-C131A 8.16. How to Replace a Flat Package IC 8.16.1. Preparation 8.16.3. Removing Solder from Between Pins • PbF (: Pb free) Solder • Soldering Iron 1. Add a small amount of solder to the bridged pins. Tip Temperature of 700°F ± 20°F (370°C ± 10°C) 2.
BL-C111A /BL-C131A 9 Disassembly and Assembly Instructions MAC address label caution hen you replace the main board, you must also attach the new MAC address label(included with the main board). Attach the new MAC address label to the unit by placing over the old MAC address label. Make sure the old address cannot be seen. Throw away the old main board.
Page 41
BL-C111A/BL-C131A 5. Remove I/O Board from Main Board. 6. Remove Angle, Screw (D) and Board Support Rubber from I/O Board .
Page 42
BL-C111A /BL-C131A 9.1.2. How To Remove Sub Board • 1-4 are the same as 9.1.1. How To Remove Main Board and I/O Board . 5. Remove six Screws (B). 6. Remove Eye Block, Pan Motor Unit, Pan Motor Angle, Connect Angle and Washer.
Page 43
BL-C111A/BL-C131A 9.1.3. How To Remove Lens Board • 1-4 are the same as How To Remove Main Board and I/O Board . 5. Remove three Screws (B). 6. Remove Eye Block and Pan Motor Unit. 7. Remove two Screws (B). 8.
BL-C111A /BL-C131A 9.2. Disassembly Instructions(BL-C131A) 9.2.1. How To Remove RF Board 1. Remove two Screws (E). And remove the Cabinet Cover. 2. Remove Screw (F) and Antenna Cable. 3. Remove Heat Rubber A and Heat Rubber B. 4. Remove Antenna Cable from RF Board, and remove RF Board from Cabinet body.
Page 45
BL-C111A/BL-C131A 9.2.2. How To Remove Main Board and I/O Board • 1-4 are the same as 9.2.1. How To Remove RF Board. 5. Remove three Cable. 6. Remove three Screws (F). 7. Remove Main Board and I/O Board form Cabinet Body. 8.
Page 46
BL-C111A /BL-C131A 9. Remove Angle, Screw (H) and Board Support Rubber from I/O Board . 9.2.3. How To Remove Sub Board • 1-4 are the same as How To Remove RF Board. • 5-7 are the same as How To Remove Main Board and I/O Board. 8.
Page 47
BL-C111A/BL-C131A 12. Remove two Screws (F) and Board support. 13. Remove two Screws (F). 14. Remove Sub Flat Cable from Sub Board. 9.2.4. How To Remove Lens Board • 1-4 are the same as 9.2.1. How To Remove RF Board. •...
Page 48
BL-C111A /BL-C131A 12. Remove two Screws (F). 13. Remove two Spacers, Pan Gear and Pan Motor Unit from Eye Block. 14. Delete solder of Main Flat Cable and remove Tilt Motor Unit. 15. Remove two Screws (F). 16. Remove Eye Left Cover, Eye Center Cover and Eye Right Cover from Lens Board.
BL-C111A/BL-C131A 10 Maintenance 10.1. Cleaning Clean the camera after the camera is turned off. 10.1.1. Cleaning the Main Unit Clean the unit with a dry and soft cloth. Note: • Do not use alcohol, polishing powder, cleanser, benzine, thinner, wax, petroleum products or hot water to wipe the camera. Also avoid pesticide, glass cleaner or hair spray.
BL-C111A /BL-C131A 11 Factory Setting 11.1. Resetting the Camera You can reset all of the camera's settings to their factory default settings. 1. Click the [Maintenance] tab. 2. On the left side of the screen under [Maintenance], click [Reset to Factory Default]. 3.
BL-C111A /BL-C131A 13 Schematic Diagram 13.1. For The Schematic Diagram Note: 1. DC voltage measurements are taken with an oscilloscope or a tester with a ground. 2. The schematic diagrams and circuit board may be modified at any time with the development of new technology.
BL-C111A /BL-C131A 16.5. Replacement Parts List (BL- Safety Ref. Part No. Part Name & Descrip- Remarks tion C111A) PSHR1335Z SPACER PQGT19330Z NAME PLATE Note: PSQT2112Z LABEL 1. RTL (Retention Time Limited) PQQT23322Z LABEL PQHG10751Z BOARD SUPPORT RUBBER The marking (RTL) indicates that the Retention Time is PSHR1323Y GUIDE, PAN GEAR POM-HB...
Page 77
BL-C111A/BL-C131A Safety Ref. Part No. Part Name & Descrip- Remarks Safety Ref. Part No. Part Name & Descrip- Remarks tion tion ECUV1A105ZFV C204 ECUE1C104ZFQ ECUE1C104ZFQ C206 ECUE1C104ZFQ C101 ECUE1C104ZFQ C208 ECUE1C104ZFQ C102 ECUE1H330JCQ C209 F1J0J1060006 C103 ECUE1C104ZFQ C240 ECUE1H221JCQ 220P C107 ECJ0EB0J224K 0.22...
Page 78
BL-C111A /BL-C131A 16.5.5. I/O Board Parts Safety Ref. Part No. Part Name & Descrip- Remarks tion R112 ERJ2GEJ103 R122 ERJ2GEJ103 Safety Ref. Part No. Part Name & Descrip- Remarks R123 ERJ2GEJ101 tion R125 ERJ2GEJ470 PCB3 PQWP3C111A I/O BOARD ASS'Y (RTL) R126 ERJ2GEJ103 R127...
Page 79
BL-C111A/BL-C131A Safety Ref. Part No. Part Name & Descrip- Remarks Safety Ref. Part No. Part Name & Descrip- Remarks tion tion D4ZZ00000024 VARISTOR (SAUGE ABSORBER) (CONNECTOR) D4ZZ00000024 VARISTOR (SAUGE CN801 K1MN20B00123 CONNECTOR, 20P ABSORBER) D4ZZ00000024 VARISTOR (SAUGE (COIL) ABSORBER) L851 PQLQR1RS241 COIL L852...
BL-C111A /BL-C131A 16.6. Replacement Parts List (BL- Safety Ref. Part No. Part Name & Descrip- Remarks tion C131A) PQGT19446Z NAME PLATE PSQT2112Z LABEL Note: PQQT23346Z LABEL 1. RTL (Retention Time Limited) PSQA2830Z LABEL PQMG10032Z RUBBER PARTS The marking (RTL) indicates that the Retention Time is PSHR1323Y GUIDE, PAN GEAR POM-HB...
Page 81
BL-C111A/BL-C131A Safety Ref. Part No. Part Name & Descrip- Remarks Safety Ref. Part No. Part Name & Descrip- Remarks tion tion (DIODES) C193 ECUV1C105ZFV MAZ30680HL DIODE(SI) C194 ECUE1C104ZFQ C196 ECUE1C104ZFQ (CAPACITORS) C200 ECUE1C104ZFQ ECUV1A105ZFV C201 ECUE1C104ZFQ ECUE1C104ZFQ C202 ECUE1C104ZFQ ECUV1A105ZFV C203 ECUE1C104ZFQ ECUV1A105ZFV...
Page 82
BL-C111A /BL-C131A Safety Ref. Part No. Part Name & Descrip- Remarks Safety Ref. Part No. Part Name & Descrip- Remarks tion tion ERJ3GEYJ103 ERJ2GEJ101 (CRYSTAL OSCILLATORS) ERJ2GEJ272 2.7K X101 H0J480500028 CRYSTAL OSCILLATOR R101 ERJ2GEJ103 X201 H0J250500061 CRYSTAL OSCILLATOR R102 ERJ2GEJ103 16.6.4.
Page 83
BL-C111A/BL-C131A Safety Ref. Part No. Part Name & Descrip- Remarks Safety Ref. Part No. Part Name & Descrip- Remarks tion tion ERJ3GEYJ750 C863 ECUV0J105KBV ERJ3GEYJ100 C864 ECUV1C473KBV 0.047 ERJ3GEY0R00 C865 ECUV0J105KBV ERJ2GEJ103 C866 ECUV0J105KBV ERJ3EKF4702 C867 ECUV1H331JCV 330P ERJ3EKF2002 C868 ECUE1H100DCQ ERJ3GEYJ272 2.7K...