Clone Programmer/Learning Setup - LG 26LH1DC1 Installation And Operating Manual
Operation guide
Hide thumbs
Also See for 26LH1DC1:
- Specifications (2 pages) ,
- Specifications (2 pages) ,
- Installation and operating manual (84 pages)
Table of Contents
Advertisement
COMMERCIAL MODE
CLONE PROGRAMMER/LEARNING SETUP
N
0
I'rl
N
J
r"
0
I'rl
Learning
the Master
TV Setup
Instructions
for the Clone Programmer to Learn the Master 26LH1 DC1 Setup.
Use MPI Cable to Connect LT2002 Clone Programmer
to
Master 26LH1DC1
MPI Port
If there is a good connection,
"THE CLONE HAS CONTROL
OF TV" message will appear. Press any button
on the
Installer remote.
Learn Setup from Master 26LH1 DCl
Press 1 to select the "LEARN FROM TV" option, then press
ON/OFE
POWER, or ENTER to go to the Memory Bank
Selection Menu. Pick the Memory "Bank" you want to store
the master 26LH1DC1s
setup in by pressing either Channel
button repeatedly
to choose Memory 1,2 or 3;.
(If you choose a Memory "Bank" that has a master device's
setup programmed into it, that setup will be overwritten
by
the new master 26LH1DC1's
setup.)
Once the Clone
memory bank is selected, press ON/OFE POWER, or ENTER.
The Clone memory bank you have selected will be shown.
Press ON/OFF or POWER to begin copying the master
26LH1DC1
's setup.
Set the Clock (Optional)
Set the time on a Master TV's Clock. (If the time has
already been copied from a TV into the Clone programmer,
you can set a master TV's clock by copying the time from
the Clone programmer.) The Clone Programmer can copy the
current time to both a master TV and to the Clone's internal
clock; accurate to within one minute. (Another reason that
the Clone programmer should be equipped with fresh,
high-quality
alkaline batteries, is for it to keep the time as
accurately
as possible.)
Since the Clone Programmer's time cannot be set directly,
the current time needs to be copied from a LG TV equipped
with M.RI. input capability.
After the time is copied to the Clone programmer, the
current time can then be transferred
to another TV. (This
can be a master TV, or another TV which has already had
the features set up.)
*Note:
When
using
the clone programmer
for teaching
or learning,
be sure
that
the heartbeat
pattern
is shown
on the LEDs.
Both
learning
and
teaching
should
take
about
4S or more
seconds
depending
on the
complexity
of the master
setup.
While
the clone
is functioning,
do not
move
it or otherwise
disturb
the clone
or wiring
connections.
If the clone
finishes
the function
in less than
4S
seconds,
redo the function
again.
Press
the reset
button
if the
clone does
not
act normally.
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION
XX
THE TV IS VERSION
XX
THE SW IS REVISION
XX
CLONE CLOCK=
XX:XX
TV CLOCK=
XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT
CLONE WHEN DONE.
,
J
This menu should appear
by
itself after the LT2002
is connected to the 26LH1DC1 MPI port.
CLONE SELECTION
MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK
FROM TV
(4) SET TV CLOCK
FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
- TO CHANGE
MENU ITEMS, PRESS
CHANNEL
KEYS OR DIGITS.
- TO EXECUTE
ITEM, PRESS ON/OFF,
POWER, OR ENTER
LT2002 Clone Programmer
Communication
Problems
• A slow flashing green light indicates there are
communication
problems between the
26LH1 DC1 and the LT2002 clone programmer.
If this is the case, check for a damaged cable,
poor contacts, or other connection
troubles.
• If the status indicator
is red, the programmer
batteries are low and should be replaced. Install
4 high-quality
alkaline AA batteries.
58
Advertisement
Table of Contents
Troubleshooting
