Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DCD800H2T
Summary of Contents for DeWalt DCD800H2T
- Page 1 DCD800 DCD805...
- Page 2 Fig. A Fig. B XXXX XX XX...
- Page 3 Fig. C Fig. D Fig. E...
-
Page 4: Technical Data
EnGLIsH DRILL DCD800 DRILL/HAMMERDRILL DCD805 Congratulations! The vibration and/or noise emission level given in this information sheet has been measured in accordance with a standardised test You have chosen a D WALT tool. Years of experience, thorough given in EN62841 and may be used to compare one tool with product development and innovation make D WALT one of the another. -
Page 5: Definitions: Safety Guidelines
EnGLIsH Batteries Chargers/Charge Times (Minutes)*** Weight (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB116 DCB117 DCB118 DCB132 DCB119 Cat # DCB546 18/54 6.0/2.0 1.08 DCB547 18/54 9.0/3.0 1.46 135* 110* 135* DCB548 18/54 12.0/4.0 1.46 DCB549 18/54 15.0/5.0 2.12 DCB181 0.35 DCB182 0.61 60/40**... -
Page 6: Work Area Safety
EnGLIsH 1) Work Area Safety e ) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool a ) Keep work area clean and well lit. Cluttered or dark in unexpected situations. areas invite accidents. -
Page 7: Residual Risks
EnGLIsH b ) Use power tools only with specifically designated to bend if allowed to rotate freely without contacting the battery packs. Use of any other battery packs may create workpiece, resulting in personal injury. a risk of injury and fire. • Always start drilling at low speed and with the bit tip c ) When battery pack is not in use, keep it away from in contact with the workpiece. -
Page 8: Important Safety Instructions For All Battery Chargers
EnGLIsH If the supply cord is damaged, it must be replaced only by • Pull by plug rather than cord when disconnecting WALT or an authorised service organisation. charger. This will reduce risk of damage to electric plug and cord. Mains Plug Replacement •... -
Page 9: Charger Cleaning Instructions
EnGLIsH Charger Cleaning Instructions Charge Indicators WARNING: Shock hazard. Disconnect the charger Charging from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a Fully Charged cloth or soft non-metallic brush. Do not use water or any cleaning solutions. -
Page 10: Storage Recommendations
EnGLIsH may result. Damaged battery packs should be returned to Use Mode: When the FLEXVOLT battery stands alone or is in service centre for recycling. WALT 18V product, it will operate as an 18V battery. When the FLEXVOLT battery is in a 54V or a 108V (two 54V batteries) WARNING: Fire hazard. -
Page 11: Battery Type
EnGLIsH Markings on Tool Charge only between 4 ˚C and 40 ˚C. The following pictograms are shown on the tool: Only for indoor use. Read instruction manual before use. Wear ear protection. Discard the battery pack with due care for the environment. Wear eye protection Charge D WALT battery packs only with designated WALT chargers. - Page 12 EnGLIsH ASSEMBLY AND ADJUSTMENTS The belt hook and magnetic bit holder can be be attached to either side of the tool using only the screw provided, to WARNING: To reduce the risk of serious personal accommodate left‑ or right‑ handed users. If the hook or injury, turn tool off and disconnect battery pack magnetic bit holder is not desired at all, it can be removed from before making any adjustments or removing/...
-
Page 13: Operation
EnGLIsH the dual range gear shifter is either completely pushed forward 2. Grasp the black sleeve of the chuck with one hand and or completely pushed back. use the other hand to secure the tool. Rotate the sleeve anticlockwise (as viewed from the front) far enough to Pivoting LED Worklight (Fig. -
Page 14: Maintenance
EnGLIsH MAINTENANCE CAUTION: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip the drill firmly to control Your power tool has been designed to operate over a long the twisting action and avoid injury. period of time with a minimum of maintenance. Continuous 6. - Page 15 EnGLIsH • Run the battery pack down completely, then remove it from the tool. • Li‑Ion cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly.