Page 1
MZ-E25 SERVICE MANUAL US Model Canadian Model AEP Model UK Model E Model Australian Model Model Name Using Similar Mechanism US and foreign patents licensed from Dolby Laboratories Licensing Corporation. Mechanism Type MT-MZE35-140 Optical Pick-up Name ODX-1B SPECIFICATIONS PORTABLE MINIDISC PLAYER...
Page 2
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Page 3
SECTION 1 This section is extracted from instruction manual. GENERAL – 3 –...
Page 5
SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. UPPER LID ASS’Y BOTTOM MAIN BOARD ORNAMENTAL MECHANISM OPTICAL PICK-UP PANEL ASS’Y BELT ASS’Y DECK SECTION (ODX-1B) (MT-MZE35-140) SECTION ASS’Y Note: Follow the disassembly procedure in the numerical order given. 2 precision screw UPPER LID ASS’Y (M1.4)
Page 6
MAIN BOARD 3 two screws 3 two screws (M1.4 × 2) (M1.4 × 2) 4 two precision screws (M1.4) 2 switch unit (CN801) 1 battery case lid 5 Open the MAIN board to the arrow direction. 8 MAIN board 6 flexible board (CLV) (CN551) 7 flexible board (CN501)
Page 7
ORNAMENTAL BELT ASS’Y 2 Expand ornamental belt ass’y in the arrow direction to remove. 1 boss 1 boss 1 boss 1 boss 1 boss 1 boss MECHANISM DECK SECTION (MT-MZE35-140) 1 two screws (MD) 2 Set chassis ass’y 3 mechanism deck section (MT-MZE35-140) –...
Page 9
SECTION 3 TEST MODE General Configuration of TEST Mode • In the TEST mode, this set provides the Auto mode in which The TEST mode configuration of this set is as follows: both CD and MO are adjusted automatically. In the Auto mode, whether a disc is CD or MO is discriminated, then each +key adjsutment is automatically executed sequentially.
Page 10
2. Description of Each Mode (To page 9 ) 010 Offset Adjustment Mode Description Focus error offset Tracking error offset All servo ON LOW REF CD Adj. 0 4 0 020 Laser Power Adjustment Each time key is 041-048 pressed, Mode Description modes are switched.
Page 11
060 Sled Movement AUDIO Mode • Enter the TEST mode, and press VOL − key, ( key, and VOL Mode Description + key in this order to select the AUDIO mode. • To select other modes, refer to the TEST mode configuration. Sled IN Sled OUT 5 1.
Page 12
3 0 0 2. Insert the CD Test disc (TDYS-1) or commercially available SONY MO disc (already recorded). 3. Press ( key twice, and the CD or MO is discriminated, then UNREG Check respective items are automatically adjusted in the order as listed 3 1 0 in tables below.
Page 13
Adjustment in SERVO Mode • MO AUTO Adjustment 1. Select each adjusting mode following the configuration of Mode Description SERVO mode, and the lower 2 digits of mode number and the adjusted value written to the EEPROM are displayed on the Sled IN LCD.
Page 22
5-4. IC PIN FUNCTION DESCRIPTION • MAIN BOARD IC501 SN761050A (RF AMPLIFIER) Pin No. Pin Name Function 1 to 4 IE, ID, IC, IF Signal input from the optical pick-up detector AGND — Ground terminal (analog system) I-V converted RF signal I input from the optical pick-up block detector I-V converted RF signal J input from the optical pick-up block detector AVCC —...
Page 23
• MAIN BOARD IC801 RU6715MF-0007 (SYSTEM CONTROLLER) Pin No. Pin Name Function CHG MON Charge voltage monitor input terminal Not used (fixed at “L”) UREG MON Un-regulator voltage monitor input terminal VTEMP Temperature sensor detection signal input from the RF amplifier (IC501) VREF Reference voltage (+1.25V) input from the RF amplifier (IC501) PLAY KEY...
Page 24
Pin No. Pin Name Function CLV V MON Spindle servo (V) timing signal input from the optical pick-up driver (IC551) CLV W MON Spindle servo (W) timing signal input from the optical pick-up driver (IC551) CLV U CON Spindle servo (U) drive signal output to the optical pick-up driver (IC551) CLV V CON Spindle servo (V) drive signal output to the optical pick-up driver (IC551) CLV W CON...
Page 25
SECTION 6 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark ! or dotted line with mark may have some difference from the original are seldom required for routine service.
Page 26
(2) MECHANISM DECK SECTION (MT-MZE35-140) not supplied M902 M901 The components identified by Les composants identifiés par une mark ! or dotted line with marque ! sont critiques pour la mark ! are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce not supplied ber specified.
Page 27
SECTION 7 MAIN ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark ! or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.