Epson EPL-N1200 Manual
Epson EPL-N1200 Manual

Epson EPL-N1200 Manual

Epson epl-n1200: specifications
Hide thumbs Also See for EPL-N1200:

Advertisement

top cover latch
optional
LocalTalk/Serial
interface access
cover
optional interface
card slot cover
fuser
paper stopper
power
switch

Printer Specifications

Printing
Printing method: Laser beam scanning and dry
electrophotographic process
Resolution:
600
Printing speed:
Up to 12 pages per minute depending on
the font and quantity of data
AC inlet
parallel C
interface
parallel B
interface
imaging cartridge
guides
control panel
600 dpi
First print:
Warm-up time:
Paper feed:
Paper feed
alignment:
Input paper supply
(20 lb [75g/m
paper):
paper
Paper eject:
Paper eject
capacity:
Internal
emulation:
Resident fonts:
RAM:
Imaging Cartridge (S051016)
front
Storage
cover
temperature:
Storage humidity: 35 to 85% RH
Shelf life:
Life:
The number of pages you can print with an imaging
cartridge varies depending on the type of printing. If you
print a few pages at a time or print dense text exceeding the
5% print ratio, your cartridge may print fewer pages.
Paper
Note:
Since the quality of any particular brand or type of paper may be changed
by the manufacturer at any time, EPSON cannot guarantee the quality of
any type of paper. Always test samples of paper stock before purchasing
large quantities or printing large jobs.
1/97
EPSON EPL-N1200
Less than 16 seconds with A4- or letter-
size paper
About 60 seconds at normal temperature
Automatic or manual feed
Center alignment for all sizes
2
]
Up to 250 sheets in the MP Tray
Up to 500 sheets per optional lower
cassette (up to two optional cassettes)
Up to 10 envelopes, depending on
thickness
Face down
250 sheets of 20 lb (75g/m
PS emulation (EPSONScript Level 2)
HP LJ4 Plus (PCL5e) emulation (LJ4)
HP-GL/2 emulation (GL2 mode)
LQ 24-pin printer emulation (ESC/P 2)
ESC/P 9-pin printer emulation (FX)
IBM Proprinter emulation (I239X)
35 scalable fonts in PS mode
45 scalable, 1 bitmap font in LJ4
(PCL5e) mode
2MB, expandable up to 64MB
32 to 95°F (0 to 35°C)
18 months after production
Up to 6,000 pages under the following
conditions: letter paper, continuous
printing, and 5% print ratio
EPSON EPL-N1200 - 1
2
) paper

Advertisement

Table of Contents
loading

Summary of Contents for Epson EPL-N1200

  • Page 1: Printer Specifications

    Note: Since the quality of any particular brand or type of paper may be changed by the manufacturer at any time, EPSON cannot guarantee the quality of any type of paper. Always test samples of paper stock before purchasing large quantities or printing large jobs.
  • Page 2 3. Right-click the System icon, and click Open in the menu that appears. 4. Select the Device Manager tab. 5. Select the ECP Printer Port under Ports (COM & LPT), then click the Properties button. 6. Select the Resources tab.
  • Page 3: Installing A Localtalk/Serial Module

    Ethernet print server * When your printer uses an EPSON Twinax interface card, it can be used in place of these IBM system printers: 4210, 5224 (models 1 and 2), 5256 (models 1, 2, and 3), 3218 (non-IDPS), 4214 (model 2), 5225 (models 1, 2, 3, and 4), and 5219 D01 and D02.
  • Page 4: Installing An Interface Card

    4 - EPSON EPL-N1200 7. Position the controller board so its components face the side panel of the printer and align it with the top and bottom guide rails in the printer. Then slide in the board. 8. Secure the controller board bracket with the four screws you removed earlier.
  • Page 5: Installing Lower Paper Cassettes

    “Hardware Configurations.” Installing Lower Paper Cassettes 1. Turn off the printer and unplug the power cord from the electrical outlet. 2. Disconnect any interface cables from the printer. 3. Place each lower paper cassette next to the printer so the ridged front edges face the same way as the ridged front edge of the printer.
  • Page 6: Using Onetouch Modes

    Follow these steps to change a setting using OneTouch modes: 1. Make sure the printer is turned on and the On Line light is 2. To change a mode 1 setting, press the SelecType button until the light next to the Paper Source setting comes on.
  • Page 7: Using Selectype

    If you need to change SelecType settings, follow these steps: Description 1. Make sure the printer is turned on and the On Line light is Selects the tray to load paper from; Auto loads from the tray containing 2.
  • Page 8 Stop Bit XOn/XOff Buffer Size * You can also change these settings using OneTouch modes. ** Changing the Page Protect setting reconfigures your printer memory and may erase any downloaded fonts. ***Available only on the Parallel B menu. Note: You can also change these settings using the Remote Control Panel utility as described in the Technical Information manual.
  • Page 9: Replacing The Imaging Cartridge

    If you have more left, there may be another reason your printing is faint. Be sure to install EPSON imaging cartridge #S051016 even if the cartridge you are removing has another part number. Follow these steps to replace the imaging cartridge: 1.
  • Page 10: Adjusting The Ritech Setting

    Follow the steps below: 1. Turn on the printer and let it warm up until you see the Ready message on the control panel display and the On Line light comes on. (If it doesn’t come on, press the On Line button.)
  • Page 11: Using Hex Dump Mode

    3. Open an application and print a document. Your printer prints out all the codes it receives in hexadecimal format. 4. To turn off hex dump mode, turn off the printer or reset it by pressing and holding down the ALT and Continue buttons at the same time.
  • Page 12 EPSON EPL-N1200 Fixing Paper Jams in an Optional Lower Paper Cassette If the printer stops and the Feed Jam or Paper Jam message appears, follow these steps: 1. Remove the paper tray from the lower paper cassette. 2. Remove all the paper from the cassette and discard any curled or wrinkled sheets.

Table of Contents