Table of Contents
Advertisement
ATS-SW10Ti
MAIN BOARD IC400 μPD78F1106GF (S)-GAS-AX (SYSTEM CONTROLLER)
Pin No.
Pin Name
1
O-DSP_IC_SCL
2
DSP_I2C_SDA
3
O-DSP_MUTE
4
NC
5
I-SIRCS
6
I-ST_TUNED
7
I-RDS_DATA
8, 9
NC
10
I-RDS_INT
11
I-DC-DET
12
I-AC_CUT
13
I-SA_INT
14
I-DSP_VALID
15
I-SA_DET
16
O-SA_RESET
17
O-KEY_RESET
18, 19
NC
20
EVSS1
21
LCD-SCLK
22
LCD-CSB
23
LCD-SDA
24
O-ST_MUTE
25
O-ST_CE
26
I-ST_DATA/STEREO
27
O-ST_CLK
28
O-ST_DATA_OUT
29
I-KEY_TINT
30
EVDD1
31
IPOD_ACCP
32
IPOD_CP_RESET
33
IPOD_FLAG
34
IPOD_LINE_MUTE
35
S-AIR LED
36
IPOD_DET
37
IPOD_POWER
38
IPHONE_DET_CTL
39
O-LCD_LED
40
O-SONY_LED
41
O-POWER_LED
42
IPOD_RX/FLASH
43
IPOD_TX/FLASH
44
O-DAB_TX
45
I-DAB_RX
46
NC
47
AVREF1
48
NC
49
S-AIR_3.3V_ON
50
AVREF0
51
AVSS
52
POWER_MONITOR3
53
I-SPEC
54 to 59
NC
60
POWER_MONITOR1
61
POWER_MONITOR2
62
O-KEY3.3V
63
KEY_SDA
64
O-KEY_SCL
32
I/O
O
I2C clock signal output to the digital audio processor
I/O
Two-way I2C data bus with the digital audio processor
O
Muting on/off control signal output to the digital audio processor "L": muting on
-
Not used
I
SIRCS signal input from the remote control receiver
I
Tuned detection signal input from the tuner (FM)
I
RDS data input terminal
-
Not used
I
RDS clock signal input terminal
I
Speaker DC detection signal input terminal
I
AC cut detection signal input terminal
I
Interrupt signal input from the wireless transceiver
I
Valid signal input from the digital audio processor
Wireless transceiver connection detection signal input terminal
I
"L": wireless transceiver is connected
O
Reset signal output to the wireless transceiver
O
Reset signal output to the touch sensor controller
-
Not used
-
Ground terminal
O
Serial data transfer clock signal output to the liquid crystal display
O
Chip select signal output to the liquid crystal display
O
Serial data output to the liquid crystal display
O
Tuner muting control signal output terminal
O
Chip enable signal output to the tuner (FM)
I
Serial data input from the tuner (FM)
O
Serial data transfer clock signal output to the tuner (FM)
O
Serial data output to the tuner (FM)
I
Interrupt signal input from the touch sensor controller
-
Power supply terminal (+3.3V)
I
iPod accessory power detection signal input terminal
O
Reset signal output to the EEPROM
O
Flag output to the VBUS power on/off switch for iPod protection
O
iPod line muting on/off control signal output terminal
O
LED drive signal output terminal for S-AIR indicator
I
iPod connection detection signal input terminal
O
Power supply on/off control signal output to the VBUS power on/off switch
O
iPhone accessory detection control signal output terminal
O
LED drive signal output terminal for liquid crystal display back light
O
LED drive signal output terminal for SONY indicator
O
LED drive signal output terminal for STANDBY indicator
I
Serial data input from the iPod connector
O
Serial data output to the iPod connector
I
Serial data input from the DAB tuner module
O
Serial data output to the DAB tuner module
-
Not used
I
Reference voltage (+3.3V) input terminal
-
Not used
O
Power supply on/off control signal output terminal for wireless transceiver
I
Reference voltage (+3.3V) input terminal
-
Ground terminal
I
Power monitor terminal for +3.3V power supply (digital system)
I
Destination setting terminal
-
Not used
I
Power monitor terminal for +13V power supply
I
Power monitor terminal for +5V power supply
O
Power supply control signal output terminal
I/O
Two-way I2C data bus with the touch sensor controller
O
I2C clock signal output to the touch sensor controller
Description
"L": tuned
Not used
Not used
"L": DC detect
"L": AC cut
"L": reset
"L": reset
Not used
"L": reset
"L": muting on
"H": LED on
"L": iPod is connected
"H": LED on
Not used
Not used
"L": US and Canadian models, "H": UK model
Not used
"H": power on
"H": LED on
"H": LED on
"H": power on
Advertisement
Table of Contents
