Punching In & Out Individual Parameters - Yamaha 02R96 Owner's Manual
Yamaha digital mixing console owner's manual
Hide thumbs
Also See for 02R96:
- Owner's manual (349 pages) ,
- Supplementary manual (8 pages) ,
- Installation manual (28 pages)
Table of Contents
Advertisement
156
Chapter 16—Automix
Punching In & Out Individual Parameters
During Automix rerecording, channels can be punched in and out by pressing the channel
strip [AUTO] buttons. Individual parameters can be punched in and out as follows.
Parameter
Input
Channel Levels
(faders)
Bus Out, Aux Send
Stereo Out
Pan
Input
Surround Pan
Input
EQ (F, Q, G)
All channels
EQ On/Off
Aux send 1–8 levels
Input
Effect parameters
Effects processors
(certain parameters)
1–4
User Defined Plug-Ins
Plug-Ins 1–4
(parameters 1–4)
Faders
User Defined Remote
Layers
Encoders
1. TOUCH SENSE IN on Fader Edit page must be on.
2. TOUCH SENSE OUT on Fader Edit page must be on.
If during Automix recording you punch in an individual parameter by using the controls
listed in the above table, even if some OVERWRITE buttons are on, only the existing data
of that particular parameter will be overwritten. Likewise, when you punch out an individ-
ual parameter by using the controls listed above, only that particular parameter will be
punched out.
If during Automix recording you press an [AUTO] button to punch in a channel, the exist-
ing data of all parameters for which the corresponding OVERWRITE buttons are on will be
overwritten. When you press the [AUTO] button to punch out of recording, all of those
parameters will be punched out.
When faders are grouped, if the OVERWRITE FADER button is on, pressing an [AUTO]
button, or touching the fader knob of any fader in the group (if TOUCH SENSE on the
Fader Edit page is on) puts all the corresponding channels into Record mode and all the
[AUTO] button indicators light up red. The same applies to Mute (OVERWRITE ON but-
ton) and EQ (OVERWRITE EQ button) groups.
02R96—Owner's Manual
OVER
Channel
WRITE
Set Layer to input, Fader mode to
Fader
FADER
Set Layer to Master, Fader mode to
fader
Stereo Out fader
Set Layer to input, Encoder mode
to Pan (Also use SELECTED CHAN-
PAN
NEL section PAN control, or Joy-
stick if [LINK] is on)
Select Input Layer and assign Sur-
SURR
round LFE Level or Surround Pan
Wheel to the Encoders
Turn on Auto EQ Edit In preference
(see page 199). Use SELECTED
EQ
CHANNEL EQUALIZER section (If
EQ parameter assigned to an
Encoder, also use Encoders)
Set Layer to input, Fader mode to
Aux
AUX
Set Layer to input, Encoder mode
to Aux
—
Select internal effects processors
—
Select Plug-Ins
FADER
Select User Defined Remote Layer
PAN
Select User Defined Remote Layer
Operation
Punch In
Touch fader
knob and
adjust
Press Encoder
and adjust
Press Encoder
and adjust
Adjust control
Press EQ [ON]
button
Touch fader
knob and
adjust
Press Encoder
and adjust
Push Parame-
ter 1–4 control
Push Parame-
ter 1–4 control
Touch fader
knob and
adjust
Press Encoder
and adjust
Punch Out
Release fader
2
knob
1
Press Encoder
Press Encoder
Press [AUTO]
button
Press [AUTO]
button
Release fader
2
knob
1
Press Encoder
Push Parame-
ter 1–4 control
Push Parame-
ter 1–4 control
Release fader
2
knob
1
Press Encoder
Advertisement
Table of Contents
