ABB ACS560 Quick Installation And Start-Up Manual page 170
General purpose drives standard control program
Hide thumbs
Also See for ACS560:
- Firmware manual (514 pages) ,
- Quick installation and start-up manual (306 pages) ,
- Hardware manual (240 pages)
Table of Contents
Advertisement
• If you connect only one conductor to the connector, we recommend that you put it
• If you connect only one conductor to the connector, we recommend that you put it
under the upper pressure plate.
under the upper pressure plate.
170 HI -त् व रित इं स ् ट ाले श न और स् ट ार् ट -अप गाइड
• The connectors are detachable but we do not recommend that you detach them.
• The connectors are detachable but we do not recommend that you detach them.
If you do, detach and reinstall the connectors as follows.
If you do, detach and reinstall the connectors as follows.
इनपु ट पावर के ब ल
Input power cable
Input power cable
10. इनपु ट पावर के ब ल को चरण
10. Connect the input power cable as in step 9. Use terminals L1, L2 and L3.
10. Connect the input power cable as in step 9. Use terminals L1, L2 and L3.
M5×25/35
M5×25/35
EN
HI
Frame size
Frame size
फ् र े म आकार
R6
R6
R7
R7
R8
R8
R5
R6
Terminals T1/U, T2/V and T3/W
Terminals T1/U, T2/V and T3/W
R7
•
Remove the nut that attaches the connector to its busbar.
•
Remove the nut that attaches the connector to its busbar.
R8
•
Put the conductor under the connector pressure plate and pre-tighten the
•
Put the conductor under the connector pressure plate and pre-tighten the
conductor.
T1/U, T2/V और T3/W टर् म िनल
conductor.
•
वह नट निकाले ं जो कने क ् ट र को उसके बसबार से जोड़ त ा है ।
•
Put the connector back to its busbar. Start the nut, and turn it at least two
•
Put the connector back to its busbar. Start the nut, and turn it at least two
rotations by hand.
•
कं ड क् ट र को कने क ् ट र दबाव प् ल े ट के नीचे रखे ं और कं ड क् ट र को पहले से कसे ं ।
rotations by hand.
•
कने क ् ट र को वापस अपने बसबार पर लगाएं । नट लगाएं , और हाथ से कम से कम दो बार घु म ाएँ ।
WARNING! Before using tools, make sure that the nut/screw is not cross-
WARNING! Before using tools, make sure that the nut/screw is not cross-
साधनों का इस् त े म ाल करने से पहले , सु न िश् च ित करे ं कि नट/पे ं च की क् र ॉस-थ् र े ड े ड नहीं है ।
threading. Cross-threading will damage the drive and cause danger.
threading. Cross-threading will damage the drive and cause danger.
क् र ॉस-थ् र े ड िं ग से ड् र ाइव को हानि पहु ं च े ग ी और खतरा पै द ा होगा।
•
Tighten the nut to a torque of 30 N·m (22 lbf·ft).
•
Tighten the nut to a torque of 30 N·m (22 lbf·ft).
•
नट को 30 N·m (22 lbf·ft) के टॉर् क पर कसे ं ।
•
Tighten the conductor(s) to 40 N·m (30 lbf·ft) for frame R8 or to 70 N·m
•
Tighten the conductor(s) to 40 N·m (30 lbf·ft) for frame R8 or to 70 N·m
•
कं ड क् ट र(रों ) को फ् र े म R8 के लिए 40 N·m (30 lbf·ft) या फ् र े म R8 के लिए 70 N·m (52 lbf·ft) पर
(52 lbf·ft) for frame R8.
(52 lbf·ft) for frame R8.
कसे ं ।
L1, L2 और L3 टर् म िनल
•
कॉम् ब ी पे ं च को निकाले ं जो कने क ् ट र को उसके टर् म िनल पोस् ट मे ं जोड़ त ा है , और कने क ् ट र को खीं च े ं ।
•
कं ड क् ट र को कने क ् ट र दबाव प् ल े ट के नीचे रखे ं और कं ड क् ट र को पहले से कसे ं ।
9
मे ं बताए अनु स ार कने क ् ट करे ं ।
9b
9b
9a
9a
8
8
L1, L2, L3, T1/U, T2/V, T3/W
L1, L2, L3, T1/U, T2/V, T3/W
N·m
N·m
L1, L2, L3, T1/U, T2/V, T3/W
30
30
40
40
N·m
lbf·ft
40
40
5.6
4.1
30
22.1
40
29.5
40
29.5
10b
10b
10a
10a
8
8
PE,
PE,
lbf·ft
N·m
lbf·ft
N·m
N·m
22.1
9.8
PE
22.1
9.8
29.5
9.8
29.5
9.8
N·m
lbf·ft
29.5
9.8
29.5
9.8
2.2
1.6
9.8
7.2
9.8
7.2
9.8
7.2
N·m
N·m
lbf·ft
N·m
lbf·ft
7.2
7.2
7.2
7.2
N·m
lbf·ft
7.2
7.2
1.2
0.9
1.2
0.9
1.2
0.9
1.2
0.9
Hide quick links:
Advertisement
Table of Contents
