HP MSR2000 Configuration Manual page 141
Msr series mpls
Hide thumbs
Also See for MSR2000:
- Configuration manual (453 pages) ,
- Manual (73 pages) ,
- High availability configuration manual (91 pages)
Table of Contents
Advertisement
[RouterA-GigabitEthernet2/1/1] mpls te max-link-bandwidth 10000
[RouterA-GigabitEthernet2/1/1] mpls te max-reservable-bandwidth rdm 10000 bc1 8000
bc2 5000 bc3 2000
[RouterA-GigabitEthernet2/1/1] quit
# Configure the maximum bandwidth, maximum reservable bandwidth, and bandwidth
constraints on Router B.
[RouterB] interface gigabitethernet 2/1/1
[RouterB-GigabitEthernet2/1/1] mpls te max-link-bandwidth 10000
[RouterB-GigabitEthernet2/1/1] mpls te max-reservable-bandwidth rdm 10000 bc1 8000
bc2 5000 bc3 2000
[RouterB-GigabitEthernet2/1/1] quit
[RouterB] interface pos 2/2/0
[RouterB-POS2/2/0] mpls te max-link-bandwidth 10000
[RouterB-POS2/2/0] mpls te max-reservable-bandwidth rdm 10000 bc1 8000 bc2 5000 bc3
2000
[RouterB-POS2/2/0] quit
# Configure the maximum bandwidth, maximum reservable bandwidth, and bandwidth
constraints on Router C.
[RouterC] interface gigabitethernet 2/1/1
[RouterC-GigabitEthernet2/1/1] mpls te max-link-bandwidth 10000
[RouterC-GigabitEthernet2/1/1] mpls te max-reservable-bandwidth rdm 10000 bc1 8000
bc2 5000 bc3 2000
[RouterC-GigabitEthernet2/1/1] quit
[RouterC] interface pos 2/2/0
[RouterC-POS2/2/0] mpls te max-link-bandwidth 10000
[RouterC-POS2/2/0] mpls te max-reservable-bandwidth rdm 10000 bc1 8000 bc2 5000 bc3
2000
[RouterC-POS2/2/0] quit
# Configure the maximum bandwidth, maximum reservable bandwidth, and bandwidth
constraints on Router D.
[RouterD] interface gigabitethernet 2/1/1
[RouterD-GigabitEthernet2/1/1] mpls te max-link-bandwidth 10000
[RouterD-GigabitEthernet2/1/1] mpls te max-reservable-bandwidth rdm 10000 bc1 8000
bc2 5000 bc3 2000
[RouterD-GigabitEthernet2/1/1] quit
6.
Configure an MPLS TE tunnel on Router A:
# Create MPLS TE tunnel interface Tunnel 1.
[RouterA] interface Tunnel 1 mode mpls-te
[RouterA-Tunnel1] ip address 7.1.1.1 255.255.255.0
# Specify the tunnel destination address as the LSR ID of Router D.
[RouterA-Tunnel1] destination 4.4.4.9
# Configure MPLS TE to use RSVP-TE to establish the tunnel.
[RouterA-Tunnel1] mpls te signaling rsvp-te
# Assign 4000 kbps bandwidth to CT 2 for the tunnel.
[RouterA-Tunnel1] mpls te bandwidth ct2 4000
# Set the tunnel setup priority and holding priority both to 0.
[RouterA-Tunnel1] mpls te priority 0
132
- Quick Links:
- Basic Concepts
Hide quick links:
Advertisement
Table of Contents
