Wearing The Glasstron; Using The Glasstron - Sony Glasstron PLM-A35 Service Manual
Hide thumbs
Also See for Glasstron PLM-A35:
- Operating instructions manual (30 pages) ,
- Operating instructions manual (57 pages)
Table of Contents
Advertisement
Wearing the Glasstron
WARNING
• Failure to properly fit the product (see "Proper Fit," page 9) each time may result in eye
fatigue, eye damage, or loss of visual functions and may result in accident or injury.
• This product should not be used by children age 15 or younger.
The eyes of children are still developing and may be adversely affected by use of this
product, and it may cause eye fatigue, eye damage, or loss of visual functions.
In addition, this product may not be adjusted to fit a child's head.
If you normally wear glasses while watching TV, you can use the Glasstron while wearing
glasses. When you take the Glasstron off, be careful that your regular glasses not get caught on
the Glasstron.
1
Adjust the nose piece and put on the Glasstron.
Pull out the nose piece if you wear
glasses.
Open the side pieces by grasping the
side piece tips and put on the
Glasstron.
Caution:
Be careful not to poke your eyes
with the side piece tips when
putting the Glasstron on or off.
2
Adjust the angle of the display unit.
Adjust the angle of the side pieces by
grasping the side piece tips to adjust the
display unit to the most suitable viewing
position.
You do not necessarily have to rest the
side pieces on your ears.
To use the supplied nose piece
If you are still unable to have a full view of the screen or clear picture color on the Glasstron after
performing step 2 above, replace the nose piece with the supplied nose piece*.
1 Remove the nose piece in an upward direction
while grasping the nose piece support.
* Nose piece
Black : US, Canadian models
Gray : Singapore model
18
Wearing the Glasstron (continued)
For increased comfort while wearing Glasstron
If the Glasstron fit is loose or uncomfortable, place the supplied side piece pads onto the tip of each
side piece.
Note
Use the side peace pads pocket-side inward.
4
Wear the stereo earphones.
Detach the stereo earphones from the
display unit and put them in your ears.
Notes
• If the stereo earphones are loose, we
recommend using the spare ear-pads (not
supplied).
• If your head is small, you may not be able to
use the Glasstron.
• Depending on your eyesight, you may not be
able to focus on the picture properly. In such
a case, it is not a malfunction.
20
-US
Nose piece
Side piece
2 Insert B of the supplied nose piece*
into the round notch A.
3
Adjust the width of the side pieces.
There are two settings for the side piece
width adjustment.
If the fit seems loose, insert the side
piece adjusters to the hinges of the left
and right side pieces.
To use the side piece adjusters
1 This is the original
position. Normally keep
adjusters here.
Side piece adjuster
To reset the side piece adjusters, turn the side pieces inside slightly and reverse the
above procedure.
To put the side piece adjuster back, press A to the illustrated direction until it "clicks"
into place.
Using the Glasstron
If you set the user lock , unlock it (page 25).
Before you start...
Be sure to follow the procedures in "Connecting the Glasstron" (pages 14-17) and "Wearing the
Glasstron" (pages 18-20).
WARNING
Each time this product is used, adjustment screens will appear, requiring the viewer to
properly fit the product. To prevent eye damage, do not use this product if the vertical lines
do not cross the horizontal line on the next screen.
The Glasstron includes two small (left and right) LCDs. You are watching a combined picture
created from these two screens. Although the screen position is properly aligned at the factory,
it may become misaligned if the Glasstron is deformed or damaged. Check the screen position
alignment every time you turn on the Glasstron. If you cannot have correct screen alignment,
stop using the Glasstron immediately.
1
Turn on the Glasstron using the POWER ON/OFF switch.
The POWER lamp lights up.
POWER
1-3
Using side piece
adjusters
Not using side piece
adjusters
2 Turn the side pieces
3 Slide the side piece
adjuster toward the
inside slightly then
display unit.
gently squeeze the top
4 Reinsert the side piece
and bottom of the side
piece adjuster and pull
adjuster tines into the
out to release.
hinge area between the
side piece and display
unit. Repeat the
procedure for the other
side piece.
Display unit
4
3
continued
Screen
ON/OFF
Side piece
19
-US
continued
21
-US
Advertisement
Table of Contents
