Setting name
Gn Status 9
Gn CB Fail 1
Gn CB Fail 2
Gn CT Failure
Gn Counter Alarm
Gn ΣI² Alarm
Gn PowerOn Count
Gn Hand Reset
Min O/P Energise Time
Status Configuration Menu
See also Figure 2-1 on page 16 for the programming
matrix.
Setting name
Settings Group Select
Inverted Inputs
Gn P/F Charact. Inhibit
Gn P/F Lowset Inhibit
Gn P/F Highset1 Inhibit
Gn P/F Highset2 Inhibit
Gn E/F Charact. Inhibit
Gn E/F Lowset Inhibit
Gn E/F HighSet 1 Inhibit
Gn E/F HighSet 2 Inhibit
Gn SEF/REF Delay 1 Inhibit
Gn SEF/REF Delay 2 Inhibit
Gn SEF/REF Lowset Inhibit
Gn V Inhibit
Gn Trip Circuit Fail
Gn Waveform Trig
Gn ΣI
2
Update
Gn Reset Flag & Outputs
Gn Clock Sync.
©2010 Siemens Protection Devices Limited
Ref
Applied value
2.11
2.5
2.5
2.5.3
2.14.1
2.14.1
2.14.3
2.11
2.11
ms
Ref
Applied value
2.2.1
2.11
2.3.1
2.3.2
2.3.2
2.3.2
2.3.1
2.3.2
2.3.2
2.3.2
2.4
2.4
2.4
2.8
2.10
2.13.3
2.14.1
2.11
2.2.7
7SG11 Argus 2 Diagrams and Parameters
Setting name
Gn Status 1 P/U Delay
Gn Status 1 D/O Delay
Gn Status 2 P/U Delay
Gn Status 2 D/O Delay
Gn Status 3 P/U Delay
Gn Status 3 D/O Delay
Gn Status 4 P/U Delay
Gn Status 4 D/O Delay
Gn Status 5 P/U Delay
Gn Status 5 D/O Delay
Gn Status 6 P/U Delay
Gn Status 6 D/O Delay
Gn Status 7 P/U Delay
Gn Status 7 D/O Delay
Gn Status 8 P/U Delay
Gn Status 8 D/O Delay
Gn Status 9 P/U Delay
Gn Status 9 D/O Delay
see note below
Gn Alarm 1 *
see note below
Gn Alarm 2 *
see note below
Gn Alarm 3 *
see note below
Gn Alarm 4 *
see note below
Gn Alarm 5 *
* The text of these setting names reflects the value
applied to the 'Set Alarm n' settings in the 'System
Config.' menu.
Comms Interface Menu
Setting name
Comms Protocol
IEC Class 2 Measurand
Class 2 Update
IEC Class 2 Scaling
Comms Baud Rate
Comms Parity
Ref
Applied value
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.11
sec
2.2.5
2.2.5
2.2.5
2.2.5
2.2.5
Ref
Applied value
4.1.1
4.2.6
4.2.7
sec
4.2.8
4.2.9
baud
4.2.10
P20009 Page 13 of 37