Bosch AQUATAK 1350 Operating Instructions Manual page 15
Hide thumbs
Also See for AQUATAK 1350:
- Installation, servicing and user instructions (4 pages) ,
- Operating instructions manual (34 pages)
Advertisement
Available languages
Available languages
F016 L69 975.book Seite 3 Dienstag, 2. November 2004 8:58 08
For Your Safety
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
Electrical Safety
Your machine requires an earth connection. The op-
erating voltage is 230 V AC, 50 Hz. Only use ap-
proved extension cables. Contact your Bosch Serv-
ice Centre for details.
If you want to use an extension cable when operat-
ing your high pressure washer, only the following ca-
ble dimensions should be used:
2
1.5 mm
– max length 20 m
2
2.5 mm
– max length 50 m
Note: If an extension cable is used it must be
earthed and connected through the plug to the earth
cable of your supply network in accordance with pre-
scribed safety regulations.
If in doubt contact a qualified electrician or the near-
est Bosch Service Center.
WARNING! Inadequate extension cables can be
dangerous. Extension cable, plug and socket
must be of watertight construction and intended
for outdoor use.
Cable connections should be kept dry and off
ground.
It is recommended for increased electrical safety to
use a Residual Current Device (RCD) with a tripping
current of not more than 30 mA. Always check your
RCD every time you use it.
For products not sold in GB: WARNING: For safety,
it is essential that the mains plug attached to the
product is fitted to the power supply cable . The cou-
plings of connection leads must be protected against
splashes and the coupling sockets on the leads must
be made of rubber or coated with rubber. Fixing
means for the connection leads must be used.
If the supply cord is damaged, it must be replaced by
a Bosch Service Centre.
Products sold in GB only: Your product is fitted with
an approved 13 A (BS 1363/A) electric plug and is
protected by a 13 A fuse (ASTA Approved to
BS 1362).
If the fitted plug is not suitable for your socket out-
lets, it should be cut off and an appropriate plug fitted
in its place.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inserted
into a 13 A socket elsewhere.
1 • F016 L69 975 • TMS • 29.10.04
Assembly
Water connection
/
/
Fit cable winder 3, using screws pro-
A
B
C
vided (four on Aquatak 1350)
Fit handle 7 to hose drum 6. (AQUATAK 1500 X)
D
Screw inlet connector 9 onto machine water inlet
E
connection 14.
Connecting high pressure water supply hose/
nozzle
/
Securely screw high pressure hose 11 onto
G
H
machine at connection 15.
/
Securely screw the high pressure hose 11 to
I
J
the hose drum 6 and to the power gun 4. (AQUATAK
1500 X)
Inserting the vario-jet/fan power lance 5 into the
L
power gun 4. Depress and turn the vario-jet/fan
power lance 90° clockwise to lock in place.
Attach water supply hose (not supplied) to the
F
mains water supply and machine.
Before use (Aquatak 1500 X only)
Unwind the pressure hose 11 off the hose
K
drum 6.
Never use the pressure washer with the high pres-
sure hose 11 on the hose drum 6.
Adjustments and using different
nozzles
Vario-jet-fan power lance
(Colour coded yellow – AQUATAK 1350/
Colour coded green – AQUATAK 1500 X)
M
Twist the front ring to adjust from a pencil to a fan
jet and vice versa.
N
To apply the detergent twist the rear ring as
shown from high pressure mode to low pressure
mode.
To adjust the spray pattern twist the front ring.
Roto power lance
(Colour coded yellow – AQUATAK 1350/
Colour coded orange – AQUATAK 1500 X)
P
Turn the vario-jet/fan power lance 5 90° anti-
clockwise. Extract the vario-jet/fan power lance.
Q
Insert the roto-power lance 10 into the power
gun 4. Depress and turn the roto-power lance 90°
clockwise to lock in place.
English - 3
Advertisement
