Content Content Your eCharger Intended use Important notes Notes for batteries How to charge Useful tips for charging Maintenance and care Technical Data Disposal information...
Your eCharger Your eCharger clic ① Charging slots ③ Status / power LEDs ② Cavity for receiver ④ Contact for power supply units, LifeTube, domes ⑤ Power supply with and earmolds country-specific adapters...
This eCharger is intended to charge rechargeable batteries in Siemens hearing instruments. Read and follow the instructions of this user guide to avoid injuries and to protect the eCharger and the hearing instruments from damage. Explanation of symbols Points out a situation that could lead to serious, moderate, or minor injuries.
Important notes Important notes NOTICE Your device is sensitive to extreme heat, high humidity, strong magnetic fields (> 0.1T), X-rays and mechanical stress. Do not expose your device to extreme temperature or high humidity. Do not leave it in direct sunlight. ...
Page 6
Please make sure that the power plug is easily accessible to remove it from power supply if necessary. This product does not have a power switch. It is ■ turned on when the power cord is plugged in. The eCharger is intended only for indoor use. ■...
Page 7
Important notes DANGER Incorrect use of the rechargeable battery can cause the rechargeable battery to burst. Discharging chemicals are spontaneously inflammable. Risk of overheating, explosion and fire! Do not ignore the red LED on the charger (refer to the LED status table)! Replace the rechargeable battery when its ...
Notes for batteries Notes for batteries Use only rechargeable batteries that are provided by your Hearing Care Professional. For information about correct battery size check the user guide of your hearing instruments. Make sure the rechargeable batteries are ...
① Power LED (green) indicates connection to the power supply. ② Status LEDs (multicolor) indicates current charging and drying state of the left/right hearing instrument. Preparation Connect the eCharger to a power supply. The power LED stays on continuously.
Page 10
How to charge Charging and drying The hearing instruments are first charged and then dried. Press the front button to open the eCharger and unlock the lid. Place your hearing instruments into the charging slots (refer to the picture).
Page 11
Check if the hearing instruments are turned on. eChargers status LED and state Explanation Power LED is off The eCharger is not connected to the power supply. Check whether eCharger is connected to the correct power supply. Power LED...
Page 12
Status LEDs Charging can not be initiated. shining red No hearing instruments in eCharger: Defect or wrong inlay in the eCharger. Ask your Hearing Care Professional to insert the correct inlay for your hearing instruments. Hearing instruments in eCharger: Wrong polarity of both instruments.
Page 13
Charging continues when the external temperature drops under 45°C (113°F). Place the eCharger in a cooler location. Consult your Hearing Care Professional if you encounter problems.
The rechargeable battery will be damaged or unusable when deep discharged. Only leave the hearing instruments in the eCharger when the eCharger is connected to a power supply. Remove the rechargeable batteries from the hearing instruments if you intend not to use them for several days.
Maintenance and care NOTICE The eCharger will be damaged by dissolver. Do not sterilise or disinfect the eCharger. Use a dry, soft tissue to clean the eCharger. Ask your Hearing Care Professional if the charging contacts need cleaning.
Page 17
Technical Data Technical data - Country-specific power-supply Kuantech Model KSAA0500080W1UV-1 Kuantech Model KSAS0050500080D5D Input voltage: 100-240 V AC Input current: 0.18 A RMS MAX Input frequency: 50-60 Hz Output voltage: 5 V DC Output current: 0.8 A Fuhua Model UE10W-050080SPC Input voltage: 100-240 V AC Input current:...
Amended by "Directive 2003/108/EC" (WEEE). Recycle devices, batteries and accessories according to national regulations. With the CE marking Siemens confirms compliance with the European Directive 2006/95/EC on electrical equipment designed for use within certain voltage limits. With the CE marking Siemens confirms compliance with the European Directive 2004/108/EC on electromagnetic compatibility.
Page 19
M20, M214 | heat humidity | ACC | bis D7 M28, M213 | environmental pollution | bis D8 M92, M228 | damaged device | ACC with power supply M217 | electric shock | eCharger M219 | incompatible parts | eCharger M226 | exploding battery | eCharger...