For Your Safety - Bosch GNF 20 CA Professional Operating Instructions Manual
Hide thumbs
Also See for GNF 20 CA Professional:
- Operating instructions manual (11 pages) ,
- Manual (264 pages) ,
- Original instructions manual (17 pages)
Table of Contents
Advertisement
3 609 929 A85.book Seite 2 Mittwoch, 15. März 2006 11:10 11
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety mea-
sures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfa-
miliar with the power tool or these instruc-
tions to operate the power tool. Power
tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, break-
age of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp cut-
ting edges are less likely to bind and are eas-
ier to control.
g) Use the power tool, accessories, tool bits
etc. in accordance with these instruc-
tions, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazard-
ous situation.
5) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer. A charger that is suit-
able for one type of battery pack may create
a risk of fire when used with another battery
pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and
fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects, that can make a con-
nection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
8 • 3 609 929 A85 • TMS • 13.03.06
6) Service
a) Have your power tool serviced by a quali-
fied repair person using only identical re-
placement parts. This will ensure that the
safety of the power tool is maintained.
For Your Safety
Working safely with this machine
is possible only when the operat-
ing and safety information is read
completely and the instructions
contained therein are strictly fol-
lowed. Before using for the first
time, ask for a practical demon-
stration.
Wear safety glasses, hearing protection and a
dust protection mask.
Wear protective gloves and sturdy shoes.
When necessary, wear an apron as well.
If the cable is damaged or cut through while
working, do not touch the cable and pull the
plug immediately. Never use the machine if the
cable is damaged.
When working with the machine, always hold it
firmly with both hands and make sure you are
in a secure standing position.
Always direct the cable to the rear away from
the machine.
Connect machines that are used in the open
via a residual current device (RCD) with an ac-
tuating current of 30 mA maximum. Do not op-
erate the machine in rain or moisture.
Insert the power plug only when the machine
is switched off.
Do not tighten the machine in a vise.
Always switch the machine off and wait until it
has come to a standstill before placing it down.
Don't work with materials containing asbestos.
Only use diamond cutting discs with a maxi-
mum permissible speed that is at least as high
as the no-load speed of the machine.
Check the diamond cutting discs before use.
The diamond cutting discs must be mounted in
exact alignment and be able to rotate freely.
Carry out a test run for at least 30 seconds
without any load. Do not use any diamond cut-
ting discs that are damaged, out-of-balance, or
vibrate.
Observe the dimensions of the diamond cut-
ting discs. The diameter of the hole must fit the
mounting flange 17 . Do not use any reduction
parts or adapters.
English - 2
Advertisement
Table of Contents
