(ohms) information at the time of recording. Audio signal: 327 mV (at load impedance 47 k (kilohms)), Output impedance with less The unique pixel array of Sony’s ClearVid than 2.2 k (kilohms) CMOS sensor and image processing system (new Enhanced Imaging...
Page 3
Luminance signal: 1 Vp-p, 75 (ohms) information at the time of recording. Chrominance signal: 0.286 Vp-p, 75 The unique pixel array of Sony’s ClearVid (ohms) CMOS sensor and image processing Audio signal: 327 mV (at load impedance 47 system (new Enhanced Imaging k (kilohms)), Output impedance with less than 2.2 k (kilohms)
Page 4
AC 100 V 240 V 50/60 Hz 18 W DC 8.4 V * A/V OUT 1 Vp-p 75 1 Vp-p 75 0.286 Vp-p 75 327 mV 47 k 48 29 81 mm 2.2 k HDMI OUT HDMI 170 g HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 — 4 —...
Page 5
Model information table Model HDR-CX6EK HDR-CX7 HDR-CX7E HDR-CX7K HDR-CX7EK Destination AEP, UK US, CND, J E, KR, JE AEP, E, AUS, HK, JE Color system NTSC NTSC CAM → PC Data copy PC → CAM × Supplied accessory × ×...
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
Page 7
ENGLISH JAPANESE ENGLISH JAPANESE • • • • • • • • HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 — 7 —...
C : Corrected by customer Refer to “1-3-3. Self-diagnosis Code Table”. Indicates the appropriate H : Corrected by dealer step to be taken. E : Corrected by service E.g. engineer 31 ..Reload the tape. 32 ..Turn on power again. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Page 9
Fault of writing to or erasing the Inspect the flash memory (IC2201 on the VC-493 board). flashmemory (Note 2) Note 1: After repair, be sure to perform “1-5. PROCESS AFTER FIXING FLASH ERROR”. Note 2: Refer to Service Manual, ADJ (“1-3. DESTINATION DATA WRITE”). HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Note: The length of low section will vary a little depending on the conditions. Fig. 2 Change in output voltage of R5792 on the LD-222 board VC-493 BOARD (SIDE A) R5737 IC5703 R5721 IC1803 Fig. 1 Measurement points on the LD-222 board R1846 Fig. 3 Measurement points on the VC-493 board HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Page 11
(IC1803 of VC-493 board) periphery. Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ. After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the hand- held operation. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
After fixing, this setting needs to be deactivated. Flash error code can be initialized by execution of “Clear All record-data”. Note: For “Clear All record-data”, refer to Service Manual, ADJ (“6. Record Data” of “3-2. SERVICE MODE”). HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Page 13
Part No. Description Part No. Description A-1334-455-A HOLDER (CX7-U2), SERVICE (MS) A-1334-458-A (CX7K-E23), SERVICE (MS) A-1334-461-A HOLDER (CX7KE-CEN), (MS) HDR-CX7 (CND) HDR-CX7K (KR) HDR-CX6EK (AEP, UK) Serial No. Serial No. Serial No. Part No. Description Part No. Description Part No.
Page 14
The date of manufacture on the labels should be the same as the previous Holder (MS) (circled portions shown on the below). Example: For the figure below, attach the “2007.5” label. * The replacement label and “inset (how to affix)” are supplied together with holder (MS) for service. * Affix the label Manufacturing year HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
(Part code: 1-215-869-11) Wrap insulating tape. C5206 NOTE FOR DISCONNECTING THE HARNESS (COAXIAL CABLE) When disconnecting the harness (Coaxial Cable), do not pull the harness part but pull off the connector body with tweezers etc. Harness (Coaxial Cable) Tweezers etc. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Page 25
2-2-2. LCD PANEL SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. 1 LCD Panel Section (1-1 to 1-6) (#2) Cabinet R Section (#2) (See Page 2-5) (Claw) (#2) - 3 2 1 LCD Panel Section HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Page 26
2 CK-178 Board HELP Note: On installation of the CK-178 board, adjust the position of the Night Shot switch and the Night Shot nob. 3 Loud Speaker - 1 7 3-1 (#3) 2-6 (#3) HELP HELP HELP (#2) 1 Hinge Block HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Page 29
2 Pass FP-737 flexible board through the flexible clamp 3 Install the flexible clamp in the hinge assy as shown in figure. as shown in figure. Stopper of FP-737 flexible board Flexible clamp Concave side of hinge Flexible clamp HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 HELP...
Page 30
6 Install the FP-744 flexible board in the hinge cover (rear) as shown in figure. FP-744 flexible board Hinge cover (rear) Switch 7 Install the hinge cover (rear) in the hinge assy as shown in figure. Hinge cover (rear) Switch FP-737 flexible board Plate of hinge HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 HELP...
Page 31
Cabinet R section CK-178 board Tape Loud speaker Harness arrangement Front panel section Barrier sheet HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 HELP...
In addition, ensure that the receiver is not covered with Replace only with part number specified. dusts nor exposed to strong light. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Page 44
ENGLISH JAPANESE 4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESE 4-2. SCHEMATIC DIAGRAMS (JAPANESE) Pattern box PTB-450 For PTB-450: J-6020-250-A J-6082-200-A For PTB-1450: Small pattern box J-6082-559-A PTB-1450 J-6082-557-A L = 1 m (PTB-450) L = 40 cm (PTB-1450) Ω HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Page 45
Schematic diagrams of the CM-077, VC-493 and LD-222 boards are not shown. Pages from 4-4 to 4-28 are not shown. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
R001 13PIN N.C. 14PIN 1/8W XE_A LND014 15PIN XE_A LND015 16PIN XE_A XE_A LND016 17PIN XE_A LND017 18PIN LND051 FLASH UNIT FLASH UNIT is replaced as block, so that PRINTED WIRING BOARD is omitted. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 FP-741, FLASH UNIT, SB25970 4-42...
Page 60
START/STOP START/STOP S5311 KEY_AD1(STROBE SW) FLASH REG_GND D_2.8V ZOOM_VR PH-002 CN7604 RV103 Page 4-35 (ZOOM) of Level 2 CONTROL SWITCH BLOCK (PS25970) CONTROL SWITCH BLOCK (PS25970) is replaced as block, so that PRINTED WIRING BOARD is omitted. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 PS25970 4-43...
: pattern of the rear side (The other layers’ patterns are not indicated) • Through hole is omitted. • There are a few cases that the part printed on diagram isn’t mounted in this model. • C: panel designation (JAPANESE) HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 4-44...
Page 63
Printed wiring boards of the CM-077, VC-493 and LD-222 boards are not shown. Pages from 4-45 to 4-48 are not shown. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Page 69
1-873-448- (INTERFACE CONNECTOR) Note: CN7303 (interface connector) is not supplied, HDMI but this is included in CR-084 complete board. 1-873-344- 11 Note: CN1001 is not supplied, but this is included in FP-745 flexible complete board. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 CR-084, FP-738, FP-745 4-54...
Page 71
When mounting these parts, mount new battery CAUTION holder first and attach new lithium battery next. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Note: HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 ST-165 4-56...
Page 72
Note: BH001 is not included in BATTERY FP-733 flexible board. TERMINAL J001 DC IN FP-731 1-873-330- Note: J001 is not included in FP-731 flexible board. 1-873-332- 11 FP-736 FLEXIBLE BOARD FP-736 1-873-335 >PI< 1-873-335- 12 HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 FP-731, FP-733, FP-736 4-57E...
ELECTRICAL PARTS LIST Link Link ACCESSORIES PD-324 BOARD CK-178 BOARD FP-736 FLEXIBLE BOARD PH-002 BOARD CR-084 BOARD FP-738 FLEXIBLE BOARD FP-731 FLEXIBLE BOARD ST-165 BOARD FP-744 FLEXIBLE BOARD FP-733 FLEXIBLE BOARD FP-745 FLEXIBLE BOARD FP-734 FLEXIBLE BOARD MS-363 BOARD HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
Page 74
: Argentine model AUS : Australian model : Brazilian model : Chinese model CND : Canadian model : East European model HK : Hong Kong model : Japanese model : Tourist model : Korea model : North European model HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2...
1-786-148-11 SWITCH, PUSH (1 KEY) (PANEL OPEN/CLOSE) S6009 1-771-731-21 SWITCH, SLIDE (NIGHTSHOT) S6010 1-771-138-21 SWITCH, KEY BOARD (N) S6011 1-771-138-21 SWITCH, KEY BOARD (EASY) Electrical parts list of CM-077 board is not shown. Pages 5-13 is not shown. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 5-12...
Page 86
(J001 is not included in FP-731 flexible board.) Electrical parts list of LD-222 board is not < CONNECTOR > shown. Pages 5-15 and 5-16 are not shown. 0 J001 1-815-792-11 CONNECTOR, DC-IN (7.2V) • Refer to page 5-1 for mark 0. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 5-14...
Page 88
When mounting these parts, mount new battery holder first < IC > and attach new lithium battery next. 0 IC5201 6-707-554-01 IC TPS65552DGQR Note: • Refer to page 5-1 for mark 0. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 5-18...
Page 93
When mounting these parts, mount new battery holder first specified. portant le numéro spécifié. and attach new lithium battery next. Note: CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2 — 2 —...
Page 94
HARDWARE LIST (1/4) #1: M1.7 X 2.5 #2: M1.7 X 4.0 #3: M1.7 X 2.5 #4: M1.4 X 2.5 (Tapping) (Black) (Black) (Red) (Dark Silver) 2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81 #5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping) (Black) (Silver)
Page 95
HARDWARE LIST (2/4) #21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping) (Black) (Silver) (Black) (Black) 2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11 #25: M1.7 X 3.0 #26: M1.4 X 2.0 #27: M1.4 X 2.0 #28: M1.4 X 4.0 (Tapping) (Black) (Silver)
Page 96
HARDWARE LIST (3/4) #41: M3.0 X 8.0 (Tapping) #42: M2.0 X 4.0 (Tapping) #43: M1.7 X 4.0 #44: M1.7 X 3.0 (Tapping) (Silver) (Silver) (Red) (Silver) 3-065-748-01 7-628-253-00 2-660-401-31 3-078-890-61 #45: M1.4 X 2.5 #46: M1.7 X 3.0 #47: M1.4 X 3.0 (Tapping) #48: M1.7 X 2.5 (Silver) (Red)
Page 97
HARDWARE LIST (4/4) #64: M1.7 X 5.0 (Tapping) #61: M3.0 X 10.0 #62: M2.0 X 3.0 #63: M5.0 X 12.5 (Silver) (Black) (Silver) (Black) 2-666-551-21 7-682-549-09 3-080-202-21 3-060-811-21 12.5 10.0 #65: M1.4 X 3.5 #66: M1.4 X 1.4 #67: M1.4 X 2.0 #68: M1.7 X 4.0 (Silver) (Silver)