Advertisement
4
Uncover the Look Down Lens
NOTICE:
In non-pet applications only, If look-down
is desired, peel away the look-down mask.
Do not remove the clear plastic lens.
LED Conditions
LED Condition
Cause
Steady Red
Unit Alarm
Steady Yellow
Microwave
Activation
(Walk Test)
Steady Green
PIR Activation
(Walk Test)
Flashing Red
Warm-Up Period
After Power-Up
Flashing Red
Microwave or PIR
(four-pulse
Failure
sequence)
Replace Unit
Coverage Patterns
0 m
2 m
4 m
6 m
2.4 m
2 m
Remove
masking for
Look-Down
LZ
W-X R-U, Z
0 m
7 ft
13 ft
0 ft
20 ft
Masking Lens
© 2012 Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450
5
Mount the Detector Base
NOTICE:
The Wall Tamper cannot be used in
corner mount installations or when
using the swivel bracket
.
7
Walk test the detector.
Perform this test at the time of installation and monthly thereafter. To ensure contin-
ual daily operation, the end user should be instructed to walk through the far end of
the coverage pattern. This ensures an alarm output prior to arming the system.
Remove and replace the cover to start a 90-sec Walk Test Mode.
During this Test Mode, any activity in the sensor's coverage pattern will cause a trans-
mitted alarm and LED activation. Each alarm will also extend the Test Mode.
Watch for the yellow LED to indicate the edges of the Microwave pattern. Adjust as
necessary.
Top View
8 m
10 m
11 m
7.8 ft
7 ft
B-L
N-Q
0 ft
26 ft
33 ft
35 ft
6
Install the Battery
The batteries are not installed in
the detector when it is shipped.
When installing the batteries it is
necessary to observe proper polar-
ity or the sensor may not function.
- -
+
+
+ + + +
-
-
+
+
-
- - -
Set the adjustment
as low as possible
for proper catch
performance
Green =
PIR detect
INT
Yellow =
STD
MAX
MW detect
Red =
MIN
MAX
Alarm
MIN
NOTICE:
Masking only
eliminates the PIR
portion of the
coverage and has no
effect on the
Microwave pattern.
NOTICE:
The protective zone
is the area where the
PIR and Microwave
technologies overlap.
If the Wall Tamper is desired, gently
press the spring onto the tapered shaft.
Do not force it down onto the shaft. As
you place the unit onto its base, be sure
the spring extends through the knock-out
to the wall.
When the batteries are installed, wait at
least 5 min before activating the Walk
Test Mode. The LED will stop fl ashing
when the detector is ready to test (the
sensor requires "lack of motion" to stabi-
lize on startup). Refer to LED Conditions
chart.
NOTICE:
Insert security screws after testing to
prevent covers from separating.
8
Program the control panel.
There is a two-part ID sticker lo-
cated on the
housing of the RF835E. You will
need the number on this sticker to
program the Detector into the
control panel. Refer to your panel's
Programming Guide for program-
ming information on wireless type
devices.
167770187
ID Number
167770187
Countries of Intended Use:
These poducts are intended for use in
the following countries within the Euro-
pean Union and in countries outside the
European Union:
RF835E Austria, Belgium, Denmark, Fin-
land, Greece, Luxembourg, Netherlands,
Norway, Spain, and Sweden.
RF835E-C United Kingdom, Ireland, and
France.
Reading Bosch Security Systems, Inc.
Product Date Codes
For Product Date Code information, refer to the
Bosch Security Systems, Inc. Web site at:
http://www.boschsecurity.com/datecodes/.
F01U254570| 03 | 2012.11 | 2
Advertisement
