28
Installation
Device settings
IP Device
3
•
CH: Displays the channel number.
•
Name: Enter the channel name.
•
Model Name: Displays the model name of IP device.
•
MAC: Displays the Mac address of IP device.
•
IP: Displays the IP address of IP device.
•
HTTP Port: Enter the HTTP port number. HTTPS is not supported.
•
/
: You can see other options (Driver, Profile1, Profile2,
RTSP Port, RTP Mode, Audio Recording) to click
return previous options, click
•
Driver: Selects the IP camera driver from the drop-down list.
•
Profile1: Select the camera stream on the drop-down box for
recording.
•
Profile2: Select the camera stream on the drop-down box for
streaming. For smooth live playback, the resolution of [Profile2]
set lower than resolution of [Profile1].
NOTE
•
When you select full screen mode on the [split mode],
[Profile1] operate for streaming automatically.
•
When CPU usage occupies more than 90% and then 1 minute
goes by, connection of [Profile2] is limited for the stability of
system.
•
RTSP Port: Enter the RTSP port number.
•
RTP Mode: Select the RTP mode from drop-down list.
•
Audio Recording: Check the audio recording option.
•
Setup: Click the check box of the desired channel and then
press the [Setup] button. The setup window will be displayed.
button. To
button.
NOTE
•
In case of same driver and same model, even if you select
several channels, the [Setup] button is activated.
•
The setting of the smallest channel number among the
selected channels is displayed. And, you can configure the
same settings.
•
In case of the Axis or Onvif driver, batch setup may not work
according to the camera model and the firmware.
•
In case of the LGE models, [Profile1] and [Profile2] are displayed
as [Master] and [Slave].
Audio/Sensor setting
You can configure this option when you select to [LGE] on the
[Driver] option. Select [Audio/Sensor] tab of the [Setup] window.
-
Audio In: Click the check box if you want to send the audio
from the microphone input connector.
-
Audio Type: Select the codec when you send the audio from
the microphone input connector.
-
Audio Out: Click the check box to output the audio from the
speaker.
-
Sensor: Select the sensor number on the drop-down list.
-
In Use: Marks up when you want to activate the sensor.
-
Sensor Type: Select the sensor type.
-
Relay Output: Select the relay output number
on the drop-down list.
-
Relay Type: Select the relay type.
-
Control Duration: Enter the relay time.
Motion Setting
You can configure this option when you select to [LGE] on the
[Driver] option. Select [Motion] tab of the [Setup] window.
1. Click the [Add] button. The motion detect window is
displayed. You can add the five windows maximum for
motion detection area.
2. Set the [Sensitivity] option.
3. Click the edge or corner of the window box to adjust the
window size for motion detection.
4. Click the [Save] button to save the settings.
Stream Setting
If you select to [LGE] on the [Driver] option, select the [Stream]
tab. When you select [ONVIF] on the [Driver] option, you can
configure the stream setting only. In case of [AXIS], the [Bitrate]
and the [Compression] options are activated only.
-
Stream (LGE only): Select the video stream.
-
In Use (LGE only): Click to activate the stream function.
-
Video Codec: Select the video mode (Codec) from the
dropdown list.
-
Resolution: Select the output image size of the camera.
-
Frame Rate: Set the frame rate of the image.
-
GOP: It means "Group of Pictures". The higher the GOP, the
better is the video quality of the camera. Edit the value of
GOP from 1 to 30. This setting is valid for H.264 video format
only.
NOTE
It recommended that you set the [GOP] value same as
[Frame Rate].