Network camera Operating Instructions WV-NP240 WV-NP244 Model Nos. (Lens is option.) WV-NP244 is shown above. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this manual.
Page 2
We declare under our sole responsibility that the product to Vi erklærer os eneansvarlige for, at dette produkt, som denne which this declaration relates is in conformity with the standards deklaration omhandler, er i overensstemmelse med standarder or other normative documents following the provisions of eller andre normative dokumenter i følge bestemmelserne i Directives EEC/73/23 and EEC/89/336.
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Limitation of Liability THIS PUBLICATION IS PROVIDED "AS IS" THIS PUBLICATION COULD INCLUDE WITHOUT WARRANTY KIND, TECHNICAL INACCURACIES OR TYPO- EITHER EXPRESS OR IMPLIED, INCLUDING GRAPHICAL ERRORS. CHANGES BUT NOT LIMITED TO, THE IMPLIED WAR- ADDED TO THE INFORMATION HEREIN, AT RANTIES OF MERCHANTABILITY, FITNESS ANY TIME, FOR THE IMPROVEMENTS OF FOR ANY PARTICULAR PURPOSE, OR...
Preface The network camera WV-NP240/WV-NP244 is designed to operate using a PC on a network (10BASE-T/100BASE-TX) to monitor images. By connecting to a network (LAN) or the Internet, images and audio from the camera can be monitored on a PC via a network.
About these Operating Instructions There are 2 sets of operating instructions for the WV-NP240/WV-NP244 as follows. • Operating Instructions (book, these operating instructions) • Network Operating Instructions (PDF) These "Operating Instructions" contain descriptions of how to install and connect this camera, and how to perform the required network settings.
How to remove the SD memory card ..................18 Performing the Network Settings ....................19 Install the software ........................19 Configure the network settings of the camera using the Panasonic IP setting software ..19 Troubleshooting ......................... 21 Specifications ..........................22...
(PDF) for descriptions of how to for- This camera will restart when detecting an mat an SD memory card. error caused by any reason. The camera will • It is recommended to use Panasonic’s be inoperable for around 30 seconds after SD memory card.
Page 9
Otherwise, the camera may not work Radio interference properly or performance deterioration When the camera is used near TV/radio may be caused. antenna, strong electric field or magnetic • Images saved on the SD memory card field (near a motor or a transformer), images may lead to personal information leak- may be distorted and noise sound may be age.
Major Operating Controls and Their Functions Model number is shown here. q Tripod mount base t Focus fixing screw (LOCK) w Back focus adjusting ring* y Microphone e ALC lens connector u SD card memory slot r Lens (option) * It is necessary to adjust the back focal length together with the lens adjustment.
Page 11
Access indicator i Network connector o SD memory error indicator (red) !0 AC Inlet 220V – 240V 50 Hz (only for the WV-NP240) Connect the power cord. !1 AC 24 V/DC 12 V (only for the WV-NP244) Power cable terminals •...
Lens Mounting Mount the lens by rotating it clockwise slowly. Then, connect the lens cable to the ALC lens connector of the camera. Back focus adjusting ring* Zoom lock knob ALC lens connector Focus ring CS-mount: Less than 8 mm Optional lens Lens type Model number...
How to use a vari-focal lens The following are descriptions of how to use a 2x vari-focal lens. Method of adjustment may be different depending on the lens in use. For further information, refer to the operating instructions of the lens in use. Zoom lock knob q Loosen the zoom lock knob and slide it to the "T"...
Tripod mount base It is not provided for recording/monitor- ing use. Fixing screw Step 3 <For the WV-NP240> Important: Connect the AC power cord (provided as a • Method of installation may be different standard accessory) between the AC inlet of...
Page 15
<For the WV-NP244> Step 4 Connect the power cable. Connect a LAN cable (category 5 or better) • When using AC 24 V/DC 12 V power to the network connector on the rear of the supply camera. EXT I/O CARD 1 2 3 4 LAN cable POWER...
Page 16
<Ratings> • ALARM IN OFF: Open ON: Make contact with GND (0.5 mA or more) • ALARM OUT OPEN: Open Collector or DC 4 V – DC 5 V Maximum applied voltage: 20 V CLOSE: Make contact with GND (100 mA or less) •...
[Connection example] When connecting with a PC directly AC adapter (DC 12 V) or AC 24 V power supply To an outlet (AC 230 V) LAN cable (category 5, cross) (WV-NP244 is shown above.) <Required cable> LAN cable (category 5, cross) When connecting to a network using a PoE device (hub) Video monitor (for adjustment use only)
Insert/Remove SD Memory Card How to insert an SD memory card Important: • Before inserting an SD memory card, make sure that the power of the camera is turned off. • Insert an SD memory card backside up. SD memory card slot e Insert an SD memory card into the SD memory card slot.
It is possible to perform the network settings of the camera using the IP setting software on the provided CD-ROM. When the Panasonic IP setting software does not work to perform the network settings of the camera, perform the network settings of the camera and the PC individually on the "Network setup"...
Page 20
Step 1 Step 3 Start the Panasonic IP setting software. Complete each network setup item and click the [Apply] button. Step 2 Click the [IP setting] button after selecting the MAC address/IP address of the camera to be configured. Note:...
→ Confirm the cable is firmly con- nected. When using AC 230 V (WV-NP240) • Is the power cord connected to the AC inlet firmly? → Confirm the power cord is firmly connected to the AC inlet.
WV-NP240: AC 230 V 50 Hz WV-NP244: AC 24 V or DC 12 V, PoE (DC 48 V) Power consumption WV-NP240: 5.0 W (AC 230 V 50 Hz) WV-NP244: 4.8 W (AC 24 V 50 Hz), 400 mA (DC 12 V) PoE: 4.2 W (Class 2 device)
Safety wire plate (for ceiling) ......1 pc. Screw (M2.5) ..........1 pc. The following is for the installation. Power cord (only for the WV-NP240) ..... 1 pc. * Panasonic IP setting software, the viewer software and the operating instructions (PDF) are included on the CD-ROM.