Panasonic WV-SW396A Installation Manual page 10

Network camera
Table of Contents

Advertisement

Do not damage the power cable.
Do not damage, fabricate, twist, stretch, bundle, or forci-
bly bend the power cable. Do not place heavy objects.
Keep away from heat sources.
Use of the damaged power cable may cause electric
shock, short circuit, or fire.
Consult the dealer for repair.
Do not install this product on a place that is greatly
influenced by wind.
Installation on a place where the wind speed is 40 m
{131.23 feet} or more per second may cause a fall of the
product resulting in injury or accidents.
Turn the power off when cleaning this product.
Failure to observe this may cause injury.
[Precautions for use]
This product has no power switch.
When turning off the power, disconnect the power supply
from the 24 V AC power supply or the PoE+ device. When
using both the 24 V AC power supply and the PoE+ device
for power supply, disconnect both the connections.
To keep on using with stable performance
Do not use this product in hot and humid conditions for a
long time. Failure to observe this causes component deg-
radation resulting in life shortening of this product.
Do not expose this product to direct heat sources such as a heater.
Handle this product with care.
Do not drop this product, nor apply shock or vibration to
the product. Failure to observe this may cause trouble.
Do not give a strong shock to the dome cover.
It may cause damage or water exposure.
About the PC monitor
When displaying the same image on the PC monitor for a
long time, the PC monitor may be damaged.
It is recommended to use a screen-saver.
When an error is detected, this product will restart
automatically.
This product will be inoperable for around 2 minutes after
the restart just as when the power is turned on.
Product disposal/transfer
Data saved on this product or a storage device used with this
product may lead to personal information leakage. When it is
necessary to dispose or give this product to someone, even
when for repair, make sure that there is no data on this product.
10
Do not touch the dome cover with your bare hands.
A dirty dome cover causes deterioration of picture quality.
• The rain wash coating is applied to the surface of the
dome cover. Do not directly touch the surface of the
dome cover or wipe it with a cloth or other product.
Failure to observe this may reduce the effectiveness
of the rain wash coating.
Cleaning this product body
Be sure to turn off the power before cleaning.
• When cleaning the dome cover, wash away any dirt or other
unwanted substances by pouring or spraying clean water
from a hose or spray bottle (do not wipe the dome cover
with a cloth or other product).
Do not use benzine, thinner, alcohol, or any other types of
solvents or detergents.
• When cleaning areas other than the dome cover, do
not use benzine, thinner, or any other types of solvents.
Failure to observe this may cause discoloration. When
using a chemical cloth for cleaning, read the caution
provided with the chemical cloth product.
Important:
• Improper cleaning of the dome cover may cause the
rain wash coating to become less effective. In this
case, in order to have effective rain wash coating, a
new dome cover must be purchased to replace the
existing dome cover. Consult with your dealer or con-
struction contractor.
• The camera position may be moved inadvertently while
cleaning the camera body. Restart the product or
refresh the camera position (position refresh) to correct
the camera position. Refer to the Operating Instructions
(included in the CD-ROM) for further information.
Transmission interval
Image transmission interval may become slow depending
on the network environment, PC performance, shooting
subject, access number, etc.
When the following message appears on the screen
during use
CAUTION:
POWER SUPPLY IS ONLY
INTENDED FOR USE OF
POE+(CLASS4) HUB
-IEEE802.3AT COMPLY
OR
AC24V MIN3.0A CLASS2
SUPPLY
The product may not be connected to a proper power-
supply device. Check whether the power supply device in
use is compatible with PoE+ (IEEE802.3at compliant). Or
use 24 V AC power supply.
SW396A
SW395A
SW396A
SW395A
SW396A
SW395A

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Wv-sw395aWv-sw396Wv-sw395

Table of Contents