Advertisement
Examples of use
Press the mode selector button to set the mode of a desired treatment.
Quick treatment (required time: 5 minutes)
Step 3 "MOISTURIZE"
If you do not have much time in the morning or you need to go out suddenly,
you can just use "MOISTURIZE" . This will moisturize your skin in 5 minutes.
Press the mode selector button to set "MOISTURIZE" .
Easy treatment (required time: 10 minutes)
Step 1 "CLEANSING"
Step 3 "MOISTURIZE"
Before you go out or when you have more time, "MOISTURIZE" after "CLEANSING".
This will moisturize your cleansed skin.
After the end of "CLEANSING", press the mode selector button to set "MOISTURIZE" .
Daily treatment (required time: 15 minutes)
Step 1 "CLEANSING"
Step 2 "MICRO-PAT"
Step 3 "MOISTURIZE"
This treatment is a daily standard.
After "CLEANSING", loosen up your skin by "MICRO-PAT" to allow "MOISTURIZE"
ingredients to easily permeate your skin, and give moisturizing care by make
moisturizing ingredients permeate your skin.
Weekly treatment (required time: 20 minutes)
Step 1 "CLEANSING"
Step 2 "MICRO-PAT"
Step 3 "MOISTURIZE"
Step 4 "REFRESH"
Care for your skin once every one or two weeks by using all modes.
Fine vibrations and gentle electrode switching in "REFRESH" mode will condition
your skin.
How to use
Do not use this product around eyes and ears.
(Cause of an accident or poor physical condition)
If you sense anything wrong with your skin or body during use,
immediately stop using this device and consult a dermatologist.
(Cause of an accident or poor health condition)
Step 1
"CLEANSING"
This mode is to remove fine dirt remaining in pores which cannot be removed by simple
washing and make your skin suitable for "MICRO-PAT".
. 1 . After washing your face, saturate the cotton puff attached to the head with toner.
Use your regular toner or wiping lotion with an exfoliating effect.
(Do not use a milky lotion or gel.)
Saturate the cotton puff with the toner until it seeps through the cotton puff to the
rear side.
Some toners (made only of mineral spring water or water, etc.) may not show
effects sufficiently.
2. Press the power switch. (Fig. 6)
The "LEVEL" indicator lamp will light, and the "CLEANSING" mode indicator lamp
will flash. If another mode indicator lamp flashes, press the mode selector button to
select "CLEANSING".
3. Select the potential power level ("HIGH" or "LOW") with the "LEVEL" selector button.
Select the potential power level ("HIGH" or "LOW") with the "LEVEL" selector button
according to your skin condition.
Every time the "LEVEL" selector button is pressed, the potential power level is
switched between "HIGH" and "LOW". The vibration power does not change.
The previous potential power level ("HIGH" or "LOW") is stored by the memory function.
Use at the "LOW" level is recommended for people who use this device for the first
time and who feel something unusual.
4. Hold the main body by the side plate. (Fig. 7)
Make sure to hold the body with your hand touching either of the right and left side
plates.
5. Apply the cotton puff to your skin and move the device slowly. (Fig. 8)
The mode indicator lamp will light, and the device will start to vibrate.
Use this device within 5 minutes.
After 5 minutes have elapsed, the device will stop automatically.
CAUTION
The device will not vibrate unless you apply the cotton puff to your skin while
touching the side plate. (Skin sensing function)
If the head is not vibrating, the device is not working.
Power will be automatically turned off if device is unused for 30 seconds.
(Auto-off function)
Apply head onto skin and slowly head from center to the outside of your face.
Do not keep the cotton puff on the same part of your skin, but
move it around. (Cause of skin trouble or poor health condition)
If the moisture in the cotton puff becomes insufficient or if it is hard to slide, add more
toner.
Do not use this device on the same part of your skin for more than 10 seconds.
If you feel slight current stimulation (a tingling sensation) during use, press the
"LEVEL" selector button to set the "LOW" level.
If you still feel a "tingling sensation," add more toner.
6. An automatic stop is made when 5 minutes have elapsed. (Auto-off function)
You will know the automatic stop with the ending sound.
7. Remove the ring and the cotton puff.
Wipe off the surface of the head with tissue, etc.
Do not use the cotton puff again once it is used because its reuse will cause
skin trouble.
Step 2
"MICRO-PAT"
This mode is to effectively stimulate and loosen up your skin to allow moisturizing
ingredients to easily permeate your skin.
1. Evenly spread your regular toner over your face.
Wipe the toner off your hands.
Advertisement
