Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4.
Page 4
Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna.
Connection cable (Included in the TV tuner). Wiring harness (Accessory 2) REVERSE ILLUMI REMO.CONT MUTE ANT. CONT P CONT EXT.CONT Rear view Wiring harness (Accessory 1) Navigation System (Optional) White/Black To front left speaker White Gray/Black To front right speaker Gray Green/Black.
System Connection To TV Tuner unit English (DDX8037/DDX8047/DDX8067) To Navigation System To Disc Changer etc. ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) • Audio right output (Red) ■...
Page 7
System Connection To TV Tuner unit (DDX7037/DDX7047/DDX7067) Do not connect. To Navigation System To Disc Changer etc. ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) • Audio right output (Red) ■...
Installation for Monitor/Player Unit Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). English Firewall or metal support Accessory 4 Metal mounting strap (commercially available)
Installing in Japanese-Made Cars ■ Installation on Toyota, Nissan or Mitsubishi Car using Brackets Accessory 6 (M5x6mm) or Accessory 7 (M5x7mm) Car Bracket Accessory 3 (For NISSAN Car) Accessory 6 (M5x6mm) or Accessory 7 (M5x7mm) English...
Page 10
Installation of Remote control unit ■ Install the remote control unit holder (Accessory 8). Double-stick tape (included) To prevent the Remote control unit from dropping down under your foot, install it using the Remote control unit holder. If the Remote control unit drops down under driving pedals, it will interfere with your driving and may result in a traffic accident.
Removing Monitor Unit ■ Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 5 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. 2.
Page 32
부속품 한 글 ...1 ...1 ...1 ...1 ...2 ...6 ...6 ...1...
Page 33
설치 순서 1. 단락을 방지하기 위해 이그니션에서 키를 빼고 - 배 터리를 차단합니다. 2. 각 기기의 입출력 와이어를 바르게 접속합니다. 3. 와이어링 하네스와 스피커 와이어를 접속합니다. 4. 어스,배터리,이그니션의 순서로 와이어링 하네스 의 와이어를 접속합니다. 5. 와이어링 하네스 커넥터를 본 기기에 접속합니다. 6.
Page 34
(5A) 스티어링 리모컨으로 만약 연결되지 않았으면 선이 탭으로부터 삐져 나오지 않게 해 주십시오. 전화 호출 또는 대화중 접지된 단자에 접속합니다. Kenwood네비게이션 시스템을 연결하 기위해서는 네비게이션 메뉴얼을 참조 하십시오. 사용하고 있는 안테나에 따라 모터 안테 나 컨트롤단자 또는 필름 타입 안테나의...
Page 35
접속 케이블 (TV 튜너에 포함) 와이어링 하네스 (부속품 2) REVERSE ILLUMI REMO.CONT MUTE ANT. CONT P CONT EXT.CONT 후면도 와이어링 하네스 (부속품 1) 네비게이션 시스템 (옵션) 흰색/검은색 앞 왼쪽 스피커 흰색 회색/검은색 앞 오른쪽 스피커 회색 녹색/검은색 뒤 왼쪽 스피커 녹색...
Page 36
시스템 연결 TV 튜너 기기로 한 글 (DDX8037/DDX8047/DDX8067) 네비게이션 시스템 으로 디스크 체인저 등으로 전면 예비출력 █ •오디오 좌측 출력 ( 백색 ) •오디오 우측 출력 ( 적색 ) █ 후면 예비출력 •오디오 좌측 출력 ( 백색 ) •오디오 우측 출력 ( 적색 ) █...
Page 37
시스템 연결 TV 튜너 기기로 (DDX7037/DDX7047/DDX7067) 연결하지 마십시오. 네비게이션 시스템 으로 디스크 체인저 등으로 전면 예비출력 █ •오디오 좌측 출력 ( 백색 ) •오디오 우측 출력 ( 적색 ) █ 후면 예비출력 •오디오 좌측 출력 ( 백색 ) •오디오 우측 출력 ( 적색 ) █...
Page 38
모니터/플레이어 기기를 위한 설치 나사 (M4×8) (상용) 자기-탭핑 나사 (상용) 기기가 제자리에 단단히 설치되었는지 확인하십시오. 기기가 불안정하 면, 오작동할 수도 있습니다 (예, 소리가 튈 수 있습니다). 한 글 방화벽 또는 메탈 서포트 부속품 4 메탈 마운팅 스트랩 (상용) 마운팅 슬리브의 탭을 스크류 드라이버나...
Page 39
일제 자동차에 설치하기 █ 브래킷을 사용해서 도요타, 닛산 또는 미츠비시 자동차에 설치하기 부속품 6 (M5×6mm) 또는 부속품 7 (M5×7mm) 자동차 브래킷 부속품 3 (NISSAN 자동 차용) 부속품 6 (M5×6mm) 또는 부속품 7 (M5×7mm) 한 글...
Page 40
리모컨 유닛의 설치 █ 리모컨 유닛 홀더 설치 (액세서리 8) 더블 스틱 테이프 (포함) 여러분의 발에 리모컨 유닛이 떨어지는 것을 방지하기위해서는, 리모컨 유닛 홀더를 사용해서 설치하십시오. 리모컨 유닛이 드라이브 페달 아래에 떨어지 면, 운전을 방해할 수 있습니다. 한 글 리모컨 홀더 8...
Page 41
모니터 유닛 떼어내기 █ 강화 고무 프레임 떼어내기 1. 고정 핀을 제거용 기구 5 에 대고 아래 쪽에있는 두개의 잠금 장치를 떼어내십시오. 프레임을 내려서 그림에 보이는 것처럼 앞으로 당겨내십시오. 2. 아래 쪽을 떼어냈으면, 위쪽의 두 곳도 떼어내 십시오. 프레임은 위쪽으로부터 같은 방식으로 떼어 낼...