1. Manuals
  2. Brands
  3. Electrolux Manuals
  4. Oven
  5. Built-in ovens
  6. Service manual

Electrolux Built-in ovens Service Manual

Hide thumbs Also See for Built-in ovens:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual , Instruction Book
© ELECTROLUX HOME PRODUCTS
Corso Lino Zanussi, 30
I - 33080 PORCIA /PN (ITALY)
Fax +39 0434 394096
SOI
Edition: 02.2010 - Rev. 02
SOI 02.10 FV
SERVICE MANUAL
Publication
number
599 70 59-01
IT/SERVICE/FV
1/142
COOKING
Built-in ovens
ACCESS TO THE
ACCESS PLUS
STRUCTURE
599 70 59-01

Advertisement

Table of Contents
loading

Related Manuals for Electrolux Built-in ovens

Summary of Contents for Electrolux Built-in ovens

  • Page 1 SERVICE MANUAL COOKING Built-in ovens © ELECTROLUX HOME PRODUCTS Publication ACCESS TO THE number Corso Lino Zanussi, 30 ACCESS PLUS I - 33080 PORCIA /PN (ITALY) 599 70 59-01 STRUCTURE Fax +39 0434 394096 IT/SERVICE/FV Edition: 02.2010 - Rev. 02 SOI 02.10 FV...
  • Page 2 SOI 02.10 FV 2/142 599 70 59-01...

  • Page 3: Table Of Contents

    CONTENTS 1 - INTRODUCTION-------------------------------------------------------------------------page 6 1.1 - PURPOSE OF THIS MANUAL ----------------------------------------------------- page 2 - ELECTRIC / ELECTRONIC OVENS -----------------------------------------------page 6 2.1 - DISMANTLING THE BUILT-IN OVEN-------------------------------------------- page 2.2 - DISCONNECTING FROM THE POWER SUPPLY --------------------------- page 2.3 - REMOVING THE CONTROL PANEL -------------------------------------------- page 2.3.1 - REMOVING THE BEARING CONTROL PANEL----------------------------------- page 2.3.2 - REMOVING THE CONTROL PANEL WITH NORMAL STYLING SUPPORT--------------------------------------------------------- page...
  • Page 4 2.6.3.2 - NEW METAL TANGENTIAL FAN INSTEAD OF THE ONE WITH THE PLASTIC BODY---------------------------------------- page 2.6.3.2 - REMOVING THE TANGENTIAL FAN ON ELECTRONIC VERSION WITH HOB CONTROLS -------------------------------------------- page 2.6.3.3 - REMOVING THE TANGENTIAL FAN ON ELECTRONIC PYRO VERSION ------------------------------------------------------------------- page 2.6.3.4 - REMOVING THE TANGENTIAL FAN ON ELECTROMECHANICAL PYRO VERSION --------------------------------- page 2.6.3.5 - REMOVING THE TANGENTIAL FAN ON ELECTRONIC...
  • Page 5 2.14 - THERMAL GLAZING---------------------------------------------------------------- page 100 2.15 - REMOVING THE FRONT PANEL ON NORMAL OVENS ----------------- page 101 2.16 - REMOVING THE FRONT PANEL ON PYROLYTIC OVENS ------------- page 104 2.17 - GAS HOB SECTION WITH FLEXIBLE PIPES ------------------------------- page 109 2.17.1 - HOB EXTENSION -------------------------------------------------------------------- page 2.17.2 - REMOVING THE CONTROL PROTECTION BOX-------------------- page 110...

  • Page 6: Introduction

    1 - INTRODUCTION 1.1 - PURPOSE OF THIS MANUAL The purpose of this Manual is to provide a general outline of the methods of accessing the various versions of ACCESS PLUS ovens. These accessibility descriptions set out the procedures for removing the components.

  • Page 7: Disconnecting From The Power Supply

    2.2 - DISCONNECTING FROM THE POWER SUPPLY WARNING: Before accessing any of the components inside the oven, it is essential to disconnect the oven from the power supply by removing the plug from the power socket or by turning the main switch on the domestic circuit (if featured) to "OFF".
  • Page 8 3. Remove the fixing screws for the control components. 4. Slide the indicator lights out of the front panel towards the inside. Fig. 6 1 - FIXING SCREWS FOR COMPONENT. 2 - BEARING FRONT PANEL. 5. Remove the two rear screws which secure the front panel in place (see Fig. 7). Fig.

  • Page 9: Removing The Control Panel With

    2.3.2 - REMOVING THE CONTROL PANEL WITH PANEL SUPPORT NORMAL STYLING Fig. 8 Example of styling with glass front panel 2.3.2.1 - REMOVING THE GLASS FRONT PANEL To remove the glass front panel: 1. Slide off the control knobs. Fig. 9 SOI 02.10 FV 9/142 599 70 59-01...
  • Page 10 2. Slide off the programmer buttons. Fig. 10 3. Cut the double-sided adhesive tape on the front panel at the top using a knife (see Fig. 11). Fig. 11 SOI 02.10 FV 10/142 599 70 59-01...
  • Page 11 4. Detach the front panel at the top (see Fig. 12). Fig. 12 1 - PANEL SUPPORT 2 - GLASS FRONT PANEL 5. Cut the double-sided adhesive tape on the front panel at the bottom using a knife (see Fig. 13). Fig.

  • Page 12: Removing The Programmer

    2.3.2.2 - REMOVING THE PROGRAMMER The electronic programmer can be accessed once the glass front panel has been removed. To remove the programmer, just pry open the fixing tabs with a screwdriver and extract the programmer from the front side (see Fig. 14). Fig.

  • Page 13: Repositioning The Glass Front Panel

    2.3.2.4 - REPOSITIONING THE GLASS FRONT PANEL To reposition the glass front panel: 1. Wipe off any of the old double-sided adhesive tape residue from the control panel support using a cloth (use some solvent if necessary (see Fig. 16 and 17). Fig.
  • Page 14 3. Glue the double-sided adhesive tape (part no. 358199008/6) onto the top of the front panel support (see Fig. 19). Fig. 19 1 - DOUBLE-SIDED ADHESIVE TAPE PART NO.358199008/6 2 - PANEL SUPPORT 4. Cut a 50 cm long piece of double-sided adhesive tape (see Fig. 20 and 21) Fig.
  • Page 15 5. Glue and cut the double-sided adhesive tape at the bottom of the control panel support as at the top (see Fig. 22). Fig. 22 6. Remove the protective film from the double-sided tape positioned at the top and bottom of the control panel support (see Fig.
  • Page 16 Fig. 25 8. Once you have glued the front panel, you need to exert some pressure with your hands, evenly, at the top and bottom of the front panel in order to facilitate perfect adherence (see Fig. 26 and 27). Fig.
  • Page 17 9. Replace the control knobs and the programmer buttons. Fig. 28 Fig. 29 SOI 02.10 FV 17/142 599 70 59-01...

  • Page 18: Removing The Control Components

    2.3.2.5 - REMOVING THE CONTROL COMPONENTS To remove one of the control components, simply: 1. Remove the upper panel. 2. Slide off the control knobs. 3. Unscrew the component fixing screws from the front (see Fig. 30 and 31). Fig. 30 1 - FIXING SCREWS FOR THE ENERGY REGULATOR...

  • Page 19: Pop-In/Pop-Out Styling Support

    2.3.3 - REMOVING THE CONTROL PANEL WITH POP-IN/POP-OUT STYLING SUPPORT In order to remove the control panel (front panel), firstly remove the upper panel (see chapter 2.6). 1. Remove the two screws which secure the control panel assembly in place (see Fig. 33). Fig.
  • Page 20 2. Slide off the control knobs by pulling them outwards. Fig. 35 1 - POP-IN/ POP-OUT KNOB Fig. 36 1 - POP-IN/ POP-OUT KNOB 2 - CONTROL COMPONENT SUPPORT 3 - CONTROL COMPONENT (ENERGY REGULATOR). SOI 02.10 FV 20/142 599 70 59-01...
  • Page 21 3. The screws of the control components are now accessible. Fig. 37 1 - FIXING SCREWS FOR THE CONTROL COMPONENT. 2 - PIN FOR THE COMPONENT KNOB. 4. Slide the washers off from the knob control pins (in the models where featured). Fig.
  • Page 22 6. Remove the pop-in/pop-out knob support ferrules by turning them anti-clockwise (see Fig. 40 and 41). Fig. 40 1 - SUPPORT COMPONENT FIXING FERRULE. 2 - CONTROL COMPONENT SUPPORT. 3 - CONTROL COMPONENT (ENERGY REGULATOR) Fig. 41 7. Slide off the control component supports from the front. Fig.
  • Page 23 8. Slide off the programmer buttons, where featured. Fig. 43 1 - PROGRAMMER BUTTONS 9. Remove the two programmer fixing screws, where featured. Fig. 44 1 - PROGRAMMER FIXING SCREWS 2 - CONTROL PANEL 10. Extract the programmer assembly (in the models where featured). Fig.
  • Page 24 Fig. 46 1 - PROGRAMMER ASSEMBLY 2 - CONTROL PANEL NOTE: To replace the programmer, it is necessary to release it from the related fixing bracket where it is slotted in place. Fig. 47 1 - PROGRAMMER 2 - PROGRAMMER SUPPORT BRACKET 11.

  • Page 25: Removing The Rear Panel (Various Components And Lampholder)

    2.4 - REMOVING THE REAR PANEL (various components and lampholder) In order to remove the rear panel, simply remove the two upper screws. Once the rear panel has been removed, the following components are accessible: the lampholder, the various heating elements, the convection fan motor and the terminal board with cable clamp. 2.4.1 - REAR VIEW OF NORMAL OVEN Fig.

  • Page 26: Rear View Of Electronic Pyrolytic Oven

    2.4.2 - REAR VIEW OF ELECTRONIC PYROLYTIC OVEN Fig. 49 1 - LAMPHOLDER 6 - TERMINAL BOARD 2 - ELECTRICAL CONTACTS OF GRILL- 7 - SPIT MOTOR TOP HEATING ELEMENT 8 - CONVECTION MOTOR 3 - DOOR LOCK 9 - POWER SUPPLY CABLE SAFETY THERMOSTAT 10 - CABLE CLAMP 4 - TEMPERATURE SENSOR PT500...

  • Page 27: Rear View Of Electromechanical Pyrolytic Oven

    2.4.3 - REAR VIEW OF ELECTROMECHANICAL PYROLYTIC OVEN Fig. 50 1 - FUNCTION SELECTOR 12 - DOOR LOCK 2 - TIMER SAFETY THERMOSTAT 3 - OVEN THERMOSTAT 13 - OVEN THERMOSTAT SENSOR 4 - THERMOSTAT INDICATOR LIGHT 14 - ELECTRICAL CONTACTS OF GRILL- 5 - DOOR LOCK TOP HEATING ELEMENT 6 - COOLING FAN...

  • Page 28: Removing The Terminal Board

    2.4.4 - REMOVING THE TERMINAL BOARD The terminal board for the electrical connections is pressure-fitted into its housing. To remove the terminal board, use a screwdriver to pry open the anchor tab (see Fig. 51 and Fig. 53). 2.4.4.1 - 3-POLE TERMINAL BOARD Fig.

  • Page 29: 5-Pole Terminal Board

    2.4.4.2 - 5-POLE TERMINAL BOARD Fig. 53 1 - TERMINAL BOARD 2 - ANCHOR TAB Fig. 54 1 - ELECTRICAL CONNECTIONS (see Fig. 55) 2 - TERMINAL BOARD 3 - EARTH CONNECTION 2.4.4.3 - ELECTRIC CONNECTIONS TO TERMINAL BOARDS Fig. 55 SOI 02.10 FV 29/142 599 70 59-01...

  • Page 30: Removing The Top Heating Element

    2.4.5 - REMOVING THE TOP HEATING ELEMENT The top heating element (top panel/grill) is positioned at the top inside the oven liner To remove the top heating element, once you have removed the oven from its housing and removed the rear panel: - Remove the fixing screw from the upper internal part of the oven liner (see Fig.

  • Page 31: Removing The Bottom Heating Element

    2.4.6 - REMOVING THE BOTTOM HEATING ELEMENT To remove the bottom heating element, once you have removed the rear panel: 1. Detach the connection cables from the bottom heating element Fig. 58 1 - GRILL HEATING ELEMENT 2 - TOP HEATING ELEMENT 3 - LAMPHOLDER 4 - TERMINAL BOARD 5 - CONVECTION FAN...

  • Page 32: Removing The Convection Fan Motor With Screws

    2.4.8 - REMOVING THE CONVECTION FAN MOTOR WITH SCREWS To remove the convection fan motor: 1 - Remove the convection fan from inside the oven (see Fig. 67). 2 - Detach the connection wires, marking their position. 3 - Remove the three fixing screws securing the fan in place (Fig. 60 Pos. 7). 2.4.9 - REMOVING THE CONVECTION FAN MOTOR WITH SNAP-ON JOINT To remove the convection fan with snap-on joint: 1 - Push the motor anchor tab using a screwdriver (see Fig.
  • Page 33 Fig. 63 1 - MOTOR SUPPORT BRACKET POSITIONED AT THE REAR OF THE OVEN 2 - CONVECTION FAN MOTOR To reposition the convection fan with snap-on joint: 1 - Reposition the anchor tab correctly, lifting it slightly with a Philips screwdriver (see Fig.
  • Page 34 2 - Insert the motor into the motor support bracket matching the motor tabs to the purpose-built fixing apertures (see Fig. 65). Fig. 65 1 - MOTOR SUPPORT BRACKET POSITIONED AT THE REAR OF THE OVEN 2 - CONVECTION FAN MOTOR 3 - Turn the motor anti-clockwise to secure it in place (see Fig.

  • Page 35: Removing The Convection Fan Blade

    2.4.10 - REMOVING THE CONVECTION FAN BLADE Proceed as follows to remove the convection fan blade: - Remove the grids and drip pans from the inside of the oven. - Remove the oven bottom panel by unscrewing the 2 fixing screws and slide it upwards (see Fig.

  • Page 36: Removing The Lampholder

    Once you have removed the rear panel, remove the convection heating element: 1 - Detach the connection wires, marking their position (from the rear of the oven) see chapter 2.4 entitled REMOVING THE REAR PANEL. 2 - Remove the two fixing screws (on the inside of the oven) see Fig. 68 Pos. 6. To remove the convection fan: 1 - Remove the central fixing screw, while holding the fan blade in place Caution: The fixing screw thread is reversed (anti-clockwise tightening)

  • Page 37: Removing The Door Lock On Pyrolytic Models

    2.4.13 - REMOVING THE DOOR LOCK ON PYROLYTIC MODELS To access the door lock, after removing the oven from its compartment, just remove the upper panel and unscrew the two screws on the door lock assembly (see Fig. 71 and 72). 2.4.13.1 - “METEOR”...

  • Page 38: Removing The Front Seal

    2.5 - REMOVING THE FRONT SEAL 2.5.1 - REMOVING THE FRONT SEAL ON NORMAL OVENS To remove the front seal, release the 4 fixing screws from the fixing hole, pulling the seal outwards (Fig. 73 and 74). Fig. 73 FIXING POINTS FOR FRONT SEAL Fig.

  • Page 39: Removing The Front Seal On Pyrolytic Ovens

    2.5.2 - REMOVING THE FRONT SEAL ON PYROLYTIC OVENS To remove the front seal, release the 23 anchor tabs on the seal, distributed over the whole front part towards the inside of the front (see Fig. 75), sliding them out of the holes by pulling them outwards.

  • Page 40: Upper Panels (Control Components And Boards)

    2.6 - UPPER PANELS (control components and boards) There are two panels in the upper part. A panel to access the electronic boards and the control components and a larger panel that covers the tangential cooling fan. 2.6.1 - NEW ONE-PIECE OVEN COVER From January 2010 (serial no.

  • Page 41: Upper Panel (Control Components And Boards)

    2.6.2 - UPPER PANEL (control components and boards) Once the upper panel has been removed, the following components are accessible: - In the electromechanical version, the control components (oven thermostat, function selector, energy regulators, indicator lights, etc.) - In the electronic version, the electronic boards (Control Unit and power board) and the control components.
  • Page 42 When removing a control component: oven thermostat, function selector, end-of-cooking programmer, indicator lights, etc. 1 - Remove the control panel front panel (see chapter 2.3 entitled REMOVING THE CONTROL PANEL). 2 - Detach the connection wires of the component, marking their position. 3 - Remove the fixing screws of the component (see chapter 2.3 entitled REMOVING THE CONTROL PANEL).

  • Page 43: Electromechanical Pyro Version

    2.6.2.2 - ELECTROMECHANICAL PYRO VERSION 1 - Unfasten the 3 fixing screws on the upper panel Fig. 83 Upper panel fixing screws Fig. 84 1 - DOOR LOCK 2 - OVEN THERMOSTAT 3 - END-OF-COOKING PROGRAMMER 4 - FUNCTION SELECTOR When removing a control component: oven thermostat, function selector, end-of-cooking programmer, indicator lights, etc.

  • Page 44: Normal Electronic Version

    2.6.2.3 - NORMAL ELECTRONIC VERSION 1 - Unfasten the fixing screws on the upper panel Fig. 85 Upper panel fixing screws Fig. 86 1 - KRONOS CONTROL UNIT 2 - OVC1000 POWER BOARD When removing an electronic board: 1 - Detach the connection wires, marking their position 2 - Release the board from the plastic supports (see Fig.

  • Page 45: Electronic Pyro Version

    2.6.2.4 - ELECTRONIC PYRO VERSION 1 - Unfasten the fixing screws on the upper panel Fig. 88 Upper panel fixing screws Fig. 89 1 - TEMPERATURE CONTROL POTENTIOMETER 2 - KRONOS CONTROL UNIT 3 - OVC1000 POWER BOARD 4 - FUNCTION SELECTOR 5 - DOOR LOCK When removing an electronic board: 1 - Detach the connection wires, marking their position...

  • Page 46: Normal Electromechanical Version With Hob Controls

    2.6.2.5 - NORMAL ELECTROMECHANICAL VERSION WITH HOB CONTROLS In the version with hob controls, after unscrewing the screws of the upper panel, to remove a control component: oven thermostat, function selector, hob energy regulators, indicator lights, etc. 1 - Remove the control panel front panel (see chapter 2.4 entitled REMOVING THE CONTROL PANEL depending on the styling).

  • Page 47: Electronic Pyro Version With Hob Controls

    2.6.2.6 - ELECTRONIC PYRO VERSION WITH HOB CONTROLS In the version with hob controls, after unscrewing the screws of the upper panel, to remove a control component: oven thermostat, function selector, hob energy regulators, indicator lights, etc. 1 - Remove the control panel front piece (see chapter 2.4 entitled REMOVING THE CONTROL PANEL depending on the styling).

  • Page 48: Normal Avantgarde Electronic Version

    2.6.2.7 - NORMAL AVANTGARDE ELECTRONIC VERSION In the version with Avantgarde electronic control, after unscrewing the screws fixing the upper panel, to remove the Control Unit: 1 - Remove the control panel front piece (see chapter 2.4 entitled REMOVING THE CONTROL PANEL depending on the styling).

  • Page 49: Avantgarde Electronic Pyro Version

    2.6.2.8 - AVANTGARDE ELECTRONIC PYRO VERSION In the version with Avantgarde Pyro electronic control, after unscrewing the screws fixing the upper panel, to remove the Control Unit: 1 - Remove the control panel front piece (see chapter 2.4 entitled REMOVING THE CONTROL PANEL depending on the styling).

  • Page 50: Normal Vision Electronic Version

    2.6.2.9 - NORMAL VISION ELECTRONIC VERSION In the version with Vision electronic control, after unscrewing the screws fixing the upper panel, to remove the Control Unit: 1 - Remove the control panel front piece (see chapter 2.3 entitled REMOVING THE CONTROL PANEL (Fig.

  • Page 51: Vision Electronic Pyro Version

    2.6.2.10 - VISION ELECTRONIC PYRO VERSION In the version with Vision Pyro electronic control, after unscrewing the screws fixing the upper panel, to remove the Control Unit: 1 - Remove the control panel front piece (see chapter 2.3 entitled REMOVING THE CONTROL PANEL (Fig.

  • Page 52: Upper Panel (Fan And Safety Thermostat)

    2.6.3 - UPPER PANEL (fan and safety thermostat) In both oven types (electromechanical and electronic), once the upper panel of the oven has been removed, the tangential cooling fan and the safety thermostat are accessible (as well as the hob control components, where featured).
  • Page 53 Fig. 100 1 - COOLING FAN N.B.: When mounting the tangential fan assembly, make sure you position the steam vent correctly (see Fig. 101). Fig. 101 1 - STEAM VENT 2 - TANGENTIAL FAN SOI 02.10 FV 53/142 599 70 59-01...

  • Page 54: The One With The Plastic Body

    2.6.3.2 - NEW METAL TANGENTIAL FAN INSTEAD OF THE ONE WITH THE PLASTIC BODY Due to quality improvements, from January 2010 (serial number 003….) a new metal fan with a different fixing system has gradually been introduced instead of the fan with the plastic body. To remove the fan: 1 - Unfasten the fixing screws on the upper panel.

  • Page 55: Version With Hob Controls

    2.6.3.3 - REMOVING THE TANGENTIAL FAN ON ELECTRONIC VERSION WITH HOB CONTROLS To remove one of the components: 1 - Unfasten the fixing screws on the upper panel. 2 - Detach the connection wires for the tangential cooling fan (or thermostat). 3 - Unfasten the fixing screws on the fan (or thermostat).
  • Page 56 2.6.3.4 - REMOVING THE TANGENTIAL FAN ON ELECTRONIC PYRO VERSION To remove one of the components: 1 - Unfasten the fixing screws on the upper panel. 2 - Detach the connection wires for the tangential cooling fan (or thermostat). 3 - Unfasten the fixing screws on the fan (or thermostat). 4 - Extract the component.

  • Page 57: Removing The Tangential Fan On Electromechanical

    2.6.3.5 - REMOVING THE TANGENTIAL FAN ON ELECTROMECHANICAL PYRO VERSION To remove one of the components: 1 - Unfasten the fixing screws on the upper panel. 2 - Detach the connection wires for the tangential cooling fan (or thermostat). 3 - Unfasten the fixing screws on the fan (or thermostat). 4 - Extract the component.

  • Page 58: Removing The Tangential Fan On Electronic Pyro Version With Hob Controls

    2.6.3.6 - REMOVING THE TANGENTIAL FAN ON ELECTRONIC PYRO VERSION WITH HOB CONTROLS To remove one of the components: 1 - Unfasten the fixing screws on the upper panel. 2 - Detach the connection wires for the tangential cooling fan (or thermostat).

  • Page 59: Removing The Tangential Fan On Normal

    2.6.3.7 - REMOVING THE TANGENTIAL FAN ON NORMAL AVANTGARDE ELECTRONIC VERSION To remove one of the components: 1 - Unfasten the fixing screws on the upper panel. 2 - Detach the connection wires for the tangential cooling fan. 3 - Unfasten the fixing screws on the fan. 4 - Extract the component.

  • Page 60: Removing The Tangential Fan On Avantgarde

    2.6.3.8 - REMOVING THE TANGENTIAL FAN ON AVANTGARDE ELECTRONIC PYRO VERSION To remove one of the components: 1 - Unfasten the fixing screws on the upper panel. 2 - Detach the connection wires for the tangential cooling fan. 3 - Unfasten the fixing screws on the fan. 4 - Extract the component.

  • Page 61: Removing The Tangential Fan On Normal

    2.6.3.9 - REMOVING THE TANGENTIAL FAN ON NORMAL VISION ELECTRONIC VERSION To remove one of the components: 1 - Unfasten the fixing screws on the upper panel. 2 - Detach the connection wires for the tangential cooling fan. 3 - Unfasten the fixing screws on the fan. 4 - Extract the component.
  • Page 62 2.6.3.10 - REMOVING THE TANGENTIAL FAN ON VISION ELECTRONIC PYRO VERSION To remove one of the components: 1 - Unfasten the fixing screws on the upper panel. 2 - Detach the connection wires for the tangential cooling fan. 3 - Unfasten the fixing screws on the fan. 4 - Extract the component.

  • Page 63: Removing The Normal Oven Door

    2.7 - REMOVING THE NORMAL OVEN DOOR The procedure for the removal of the oven door remains the same as in the previous models. To remove the oven door: 1 - Open the door completely. 2 - Raise the two hinge retainers (see Fig. 119, 120 and 121). 3 - Slide the door off upwards.

  • Page 64: Removing The Door External Glass Normal Oven

    Fig. 121 1 - HINGE RETAINER HOOK (IN LOCKED POSITION) 2 - OVEN HINGE N.B.: When repositioning the door, before you close it, make sure you raise the hooks completely to their original position (see Fig. 119). 2.7.1 - REMOVING THE DOOR EXTERNAL GLASS NORMAL OVEN Once you have removed the oven door: 1 - Remove the two screws on the lower part of the inner door (see Fig.

  • Page 65: Removing The Door Handle Normal Oven

    2.7.2 - REMOVING THE NORMAL OVEN DOOR HANDLE Once you have removed the external glass, you can access the oven handle. To remove the door handle, unfasten the two screws on the inside of the door (see Fig. 123 Pos. 4). Fig.

  • Page 66: Removing The "All Glass" Pyrolytic Oven Door

    2.8 - REMOVING THE “ALL GLASS” PYROLYTIC OVEN DOOR The procedure for the removal of the oven door remains the same as in the previous models. To remove the oven door: 1 - Open the door completely. 2 - Raise the two hinge retainers (see Fig. 125, 126 and 127). 3 - Slide the door off upwards.

  • Page 67: Removing The Upper End Pieces On "All Glass" Door

    Fig. 127 1 - HINGE RETAINER HOOK (IN LOCKED POSITION) 2 - OVEN HINGE N.B.: When repositioning the door, before you close it, make sure you raise the hooks completely to their original position (see Fig. 125). 2.8.1 - REMOVING THE UPPER END PIECES ON "ALL GLASS" DOOR Fig.
  • Page 68 Once you have removed the oven door: 1 - Remove the two screws on the side uprights securing the upper end pieces in place (see Fig. 129 and 130). 2 - Slide off the upper grille - upper end pieces assembly upwards (see Fig. 132). Fig.
  • Page 69 Fig. 132 1 - EXTERNAL DOOR GLASS 2 - INTERNAL DOOR GLASS 3 - UPPER END PIECES 4 - UPPER GRILLE 3 - Unfasten the upper grille - upper end pieces fixing screws (see Fig. 133). Fig. 133 1 - UPPER LEFT END PIECE 2 - UPPER GRILLE 3 - UPPER RIGHT END PIECE 4 - END PIECE SPRING CLIP...
  • Page 70 2.8.2 - REMOVING "ALL GLASS" PYRO OVEN DOOR INTERNAL GLASS To remove the door internal glass: 1 - Remove the oven door (see Chapter 2.8). 2 - Remove the upper end pieces (see Chapter 2.8.1) 3 - Remove the internal glass, paying attention to the sequence of glass panes and to the position of the rubber buffer (see Fig.

  • Page 71: Removing The "All Glass" Pyro Oven Door Handle

    IMPORTANT: Before repositioning the door internal glazing in the correct sequence, make sure that the side glazing retainer buffers are positioned correctly (see Fig. 138). Fig. 138 1 - SIDE GLAZING RETAINER BUFFERS 2 - RIGHT DOOR UPRIGHT 3 - EXTERNAL GLASS PANE 2.8.3 - REMOVING THE "ALL GLASS"...

  • Page 72: Removing The "All Glass" Pyro Oven Door Hinges

    2.8.4 - REMOVING THE "ALL GLASS" PYRO OVEN DOOR HINGES Once you have removed the internal glazing as explained in the previous chapters: 1 - Remove the two fixing screws of the hinge-hinge cover assembly inside the side door uprights (see Fig.
  • Page 73 3 - Remove the hinge from the hinge cover by unscrewing the side screw and the front one (see Fig. 144 and 145). Fig. 144 1 - DOOR HINGE 2 - SIDE FIXING SCREW FOR HINGE COVER 3 - FRONT FIXING SCREW FOR HINGE COVER 4 - HINGE COVER 5 - TORX...

  • Page 74: Removing The "Metal-Glass" Pyrolytic Oven Door

    2.9 - REMOVING THE “METAL-GLASS” PYROLYTIC OVEN DOOR The procedure for the removal of the oven door remains the same as in the previous models. To remove the oven door: 1 - Open the door completely. 2 - Raise the two hinge retainers (see Fig. 146, 147 and 148). 3 - Slide the door off upwards.

  • Page 75: Removing The "Metal-Glass" Pyro Door External Glass

    Fig. 148 1 - HINGE RETAINER FOR HINGE (IN LOCKED POSITION) 2 - OVEN HINGE N.B.: When repositioning the door, before you close it, make sure you raise the hooks completely to their original position (see Fig. 146). 2.9.1 - REMOVING THE "METAL-GLASS" PYRO DOOR EXTERNAL GLASS Once you have removed the oven door: 1 - Remove the two screws on the lower part of the inner door (see Fig.

  • Page 76: External Glass

    DETAIL OF FIXING THE EXTERNAL GLASS AND HINGE Fig. 150 1 - DOOR INTERNAL GLASS 2 - INNER DOOR 3 - OVEN HINGE (LEFT) 4 - DOOR EXTERNAL GLASS 5 - FIXING SCREW FOR EXTERNAL GLASS 6 - FIXING SCREWS FOR LEFT HINGE Fig.

  • Page 77: Removing The "Metal-Glass" Pyro Door Internal Glass

    2.9.2 - REMOVING "METAL-GLASS" PYRO OVEN DOOR INTERNAL GLASS Once you have removed the external glass from the door, you can access the door internal glass (see Fig. 153). Fig. 153 1 - DOOR HINGES 2 - METAL TABS TO SECURE THE FIRST INTERNAL GLASS 3 - FIXING BRACKETS...
  • Page 78 Fig. 156 1 - DOOR HINGE 2 - FIXING BRACKETS FOR INTERNAL GLASS 3 - SEAL BETWEEN SECOND GLASS PANE AND INNER DOOR 4 - SECOND INTERNAL GLASS PANE 5 - INNER DOOR 3 - Remove the second internal glass pane (see Fig. 157). Fig.
  • Page 79 5 - Remove the third internal glass pane (see Fig. 159). Fig. 159 1 - INNER DOOR 2 - THIRD INTERNAL GLASS PANE 3 - SEAL BETWEEN THIRD GLASS PANE AND INNER DOOR 6 - Remove the third glass - inner door seal (see Fig. 160). Fig.

  • Page 80: Removing The "Metal-Glass" Pyro Oven Door Handle

    2.9.3 - REMOVING THE "METAL-GLASS" PYRO OVEN DOOR HANDLE Once you have removed the external door glass, you can access the fixing screws for the door handle (see Fig. 162 Pos. 2). Fig. 162 1 - TORX SCREWDRIVER 2 - FIXING SCREWS FOR DOOR HANDLE 3 - METAL SUPPORTS TO SECURE...

  • Page 81: Removing The "Plastic" Oven Door

    2.10 - REMOVING THE "PLASTIC" OVEN DOOR The procedure for the removal of the oven door remains the same as in the previous models. To remove the oven door: 1 - Open the door completely. 2 - Raise the two hinge retainers (see Fig. 164, 165 and 166). 3 - Slide the door off upwards.
  • Page 82 Fig. 166 1 - HINGE RETAINER FOR HINGE (IN LOCKED POSITION) 2 - OVEN HINGE N.B.: When repositioning the door, before you close it, make sure you raise the hooks completely to their original position (see Fig. 164). Fig. 167 5 - DOOR LOCK RETAINER 1 - OVEN HINGES HOOK...

  • Page 83: Removing The "Plastic" Oven Door Internal Glass

    2.10.1 - REMOVING THE "PLASTIC" OVEN DOOR INTERNAL GLASS The door internal glass is secured in place using special retainer hooks (see Fig. 168). Fig. 168 1 - EXTERNAL DOOR GLASS 2 - INTERNAL DOOR GLASS 3 - RIGHT HINGE 4 - LEFT HINGE 5 - RIGHT GLASS RETAINER HOOK...
  • Page 84 2 - Slide off the first glass from the lower part of the door (see Fig. 170). Fig. 170 1 - FIRST DOOR INTERNAL GLASS PANE 2 - DOOR HINGES Fig. 171 1 - SECOND DOOR INTERNAL GLASS PANE 2 - LEFT HINGE 3 - RIGHT HINGE 4 - LEFT GLASS RETAINER HOOK...

  • Page 85: Removing The "Plastic" Oven Door Handle

    3 - Slide off the second glass pane from the lower part of the door (see Fig. 173). Fig. 173 1 - SECOND DOOR INTERNAL GLASS PANE Fig. 174 1 - FIXING SCREWS FOR DOOR HANDLE 2 - FIXING SCREWS FOR HINGES 3 - DOOR HINGES N.B.: In case of pyrolytic ovens, there may be three internal glass panes.

  • Page 86: Removing The Glass Retainer Hooks On "Plastic" Oven Door

    2.10.3 - REMOVING THE GLASS RETAINER HOOKS ON "PLASTIC" OVEN DOOR To remove the retainer hooks, simply slide them off the related rotation pins (see Fig. 176). Fig. 176 1 - DOOR HINGE 2 - RETAINER HOOK 3 - ROTATION PIN FOR HOOK 2.10.4 - REMOVING THE "PLASTIC"...

  • Page 87: Removing The "Hinged" Oven Door

    2.10 - REMOVING THE "HINGED" OVEN DOOR To remove the oven door: - Unfasten the front panel fixing screw (see Fig. 182). - Unfasten the upper hinge fixing screws (see Fig. 183). - Slide off the upper hinge, holding the door to prevent it from falling (see Fig. 184) 2.11.1 - POSITION OF HINGES AND DOOR LOCK Fig.

  • Page 88: Position Of Hinge Fixing Screws

    2.11.2 - POSITION OF HINGE FIXING SCREWS Fig. 181 1 - UPPER HINGE FIXING SCREWS 2 - HINGE SUPPORT 3 - LOWER HINGE FIXING SCREWS 2.11.3 - REMOVING THE FRONT PANEL SCREW Fig. 182 1 - FRONT PANEL FIXING SCREW 2 - FRONT PANEL ASSEMBLY 2.11.4 - VIEW OF THE HINGE FIXING SCREWS Fig.

  • Page 89: Removing The Upper Hinge

    2.11.5 - REMOVING THE UPPER HINGE To remove the upper hinge: - Remove the front panel fixing screw (see Fig. 182). - Unfasten the upper hinge fixing screws (see Fig. 183). - Lift the front panel slightly upwards and outwards to release the upper hinge (see Fig. 184). - Extract the hinge upwards and towards the inside of the oven (see Fig.

  • Page 90: Extracting The Upper End Pieces

    2.11.7 - EXTRACTING THE UPPER END PIECES Pull out the upper end pieces with force (see Fig. 186). Fig. 186 1 - UPPER END PIECE RIGHT SIDE 2 - UPPER PROFILE 3 - UPPER END PIECE LEFT SIDE 4 - SUPPORT UPRIGHT FOR INTERNAL GLASS N.B.: The upper profile is blocked between the...

  • Page 91: Removing The Door Internal Glass

    2.11.9 - REMOVING THE DOOR INTERNAL GLASS Once you have removed the end pieces and the upper profile, you can slide out the door internal glass pane (or panes) (see Fig. 188). Fig. 188 1 - DOOR INTERNAL GLASS 2 - SUPPORT UPRIGHT FOR INTERNAL GLASS 3 - LOWER END PIECE 2.11.10 - REMOVING THE LOWER END PIECES...

  • Page 92: Extracting The Lower End Pieces

    Once you have removed the internal door glass pane (or panes), unfasten the lower right end piece fixing screw (see Fig. 190). Fig. 190 1 - LOWER END PIECE RIGHT SIDE 2 - SUPPORT UPRIGHT FOR INTERNAL GLASS 3 - INTERNAL FIXING SCREW IMPORTANT: As from production week 39 of 2007 (serial no.

  • Page 93: View Of The Lower End Piece

    2.11.12 - VIEW OF THE LOWER END PIECE Fig. 192 1 - LOWER END PIECE SOI 02.10 FV 93/142 599 70 59-01...

  • Page 94: Adjusting The "Hinged" Door Alignment

    2.12 - ADJUSTING THE "HINGED" DOOR ALIGNMENT To align the door to the front panel (see Fig. 193), once you have extracted the oven from its compartment - even partially - simply turn the adjustment screw (see Fig. 194 Pos.1) in the following sequence: 1 - Loosen the two upper screws (see Chapter 2.12.1).

  • Page 95: Door Alignment Adjustment Screw

    2.12.2 - DOOR ALIGNMENT ADJUSTMENT SCREW Fig. 195 3 - DJUSTMENT SCREW FOR DOOR ALIGNMENT 4 -DOOR OPEN DURING ADJUSTMENT Fig. 196 SOI 02.10 FV 95/142 599 70 59-01...
  • Page 96 Unscrew the adjustment screw to lower the door (see Fig.196 and 197). Fig. 197 Tighten the adjustment screw to raise the door (see Fig. 196 and 198). Fig. 198 SOI 02.10 FV 96/142 599 70 59-01...

  • Page 97: Manual Door Release In Pyrolytic Ovens

    2.13 - MANUAL DOOR RELEASE IN PYROLYTIC OVENS To release the door manually on Access Plus ovens, turn the hook fixing screw or lift up the hook (depending on the door lock type, see chapters 2.13.3 and 2.13.4) through the hole featured on the oven front part.

  • Page 98: Position Of The Lock Hole On Models With

    2.13.2 - POSITION OF THE LOCK HOLE ON MODELS WITH RIGHT "HINGED" DOOR Fig. 200 2.13.3 - RELEASE ON MODELS WITH “METEOR” DOOR LOCK To release the door manually on Access Plus ovens with "METEOR" door lock, turn the hook fixing screw through the hole featured on the oven front part (see chapters 2.13.1 and 2.13.2).

  • Page 99: Release On Models With "Eltek" Door Lock

    2.13.4 - RELEASE ON MODELS WITH “ELTEK” DOOR LOCK To release the door manually on Access Plus ovens with "ELTEK" door lock, directly move the hook through the hole featured on the oven front part (see chapters 2.13.1 and 2.13.2). 1 - Insert a 3 mm screwdriver into the hole to lift up the lock hook by about 3 mm to allow the door lock to be released (see Fig.

  • Page 100: Thermal Glazing

    2.14 - THERMAL GLAZING “Thermal Glazing” are special oven glass panes which undergo a special treatment on one side of the pane. This treatment allows the glass to provide improved heat insulation (higher temperature reduction on the external side of the door). When assembling the glass on the oven door, you must make sure that the treated glass pane is positioned facing the oven interior.

  • Page 101: Removing The Front Panel On Normal Ovens

    2.15 - REMOVING THE FRONT PANEL ON NORMAL OVENS To access the oven front panel, once you have removed the oven door and the front seal: 1 - Unfasten the 6 front panel fixing screws on the front (for views of the screws, see Fig. 205 and 206).
  • Page 102 Fig. 207 1 - LOWER FIXING SCREWS 2 - OVEN FRONT PANEL 2 - Unfasten the 4 side fixing screws (2 on each side see Fig. 208 and 209). Fig. 208 Fig. 209 1 - SIDE FIXING SCREW. 2 - OVEN FRONT PANEL. SOI 02.10 FV 102/142 599 70 59-01...
  • Page 103 3 - Unscrew the front panel fixing screw in the lower part of the oven (see Fig. 210 and 211). Fig. 210 Fig. 211 1 - OVEN FRONT PANEL 2 - LOWER FIXING SCREW 3 - OVEN UNDERSIDE 4 - Remove the front panel. To reposition the front panel: 1 - First position the upper part of the front panel 2 - Then insert the front panel completely...

  • Page 104: Removing The Front Panel On Pyrolytic Ovens

    2.16 - REMOVING THE FRONT PANEL ON PYROLYTIC OVENS To access the oven front panel, once you have removed the oven door and the front seal: 1 - Unfasten the 6 front panel fixing screws on the front (for views of the screws, see Fig. 212, 213 and 214).
  • Page 105 Fig. 214 1 - LOWER FIXING SCREWS 2 - OVEN FRONT PANEL 2 - Unfasten the 4 side fixing screws (2 on each side see Fig. 215 and 216). Fig. 215 Fig. 216 1 - SIDE FIXING SCREW. 2 - OVEN FRONT PANEL. SOI 02.10 FV 105/142 599 70 59-01...
  • Page 106 3 - Unscrew the front panel fixing screw in the lower part of the oven (see Fig. 217 and 218). Fig. 217 Fig. 218 1 - OVEN FRONT PANEL 2 - LOWER FIXING SCREW 3 - OVEN UNDERSIDE SOI 02.10 FV 106/142 599 70 59-01...
  • Page 107 4 - Unfasten the 4 fixing screws of the fan deflector (2 on each side) to access the front panel upper fixing screw (see Fig. 219 and 220). Fig. 219 1 - FIXING SCREWS - FAN DEFLECTOR 2 - TORX SCREWDRIVER Fig.
  • Page 108 6 - Unfasten the front panel upper fixing screw (see Fig. 222). Fig. 222 1 - OVEN FRONT PANEL 2 - TORX SCREWDRIVER 3 - UPPER FIXING SCREW FOR FRONT PANEL 4 - FAN DEFLECTOR 7 - Remove the front panel. To reposition the front panel: 1 - First position the upper part of the front panel 2 - Then insert the front panel completely...

  • Page 109: Gas Hob Section With Flexible Pipes

    2.17 - GAS HOB SECTION WITH FLEXIBLE PIPES The gas hob with flexible pipes is positioned in the upper part of the oven. To access the components of the hob and the upper components of the oven, it is necessary to extract the hob-oven assembly from its built-in compartment.

  • Page 110: Removing The Control Protection Box

    2.17.2 - REMOVING THE CONTROL PROTECTION BOX To access the timer, the function selector, the oven thermostat and the indicator lights, you need to remove the control protection box by unscrewing the two fixing screws (see Fig. 226 and 227). Fig.

  • Page 111: Removing The Tangential Fan Protection Box

    2.17.3 - REMOVING THE TANGENTIAL FAN PROTECTION To access the tangential cooling fan, you need to remove the tangential fan protection box by unscrewing the 4 screws (see Fig. 228, 229 and 230). Fig. 228 1 - GAS BURNER 2 - TANGENTIAL FAN PROTECTION BOX 3 - FIXING SCREWS FOR THE BOX, LEFT SIDE...
  • Page 112 2 - Move the box towards the front (see Fig. 231). Fig. 231 1 - TANGENTIAL FAN PROTECTION BOX 3 - Lift the box upwards (see Fig. 232). Fig. 232 1 - TANGENTIAL FAN PROTECTION BOX SOI 02.10 FV 112/142 599 70 59-01...

  • Page 113: Removing The Tangential Cooling Fan

    2.17.4 - REMOVING THE TANGENTIAL COOLING FAN To remove the tangential cooling fan, once you have removed the protection box: 1 - Unfasten the two side screws (see Fig. 233, 234 and 235) 2 - Disconnect the connection wires. Fig. 233 1 - PLASTIC FAN BODY 2 - FIXING SCREWS - 3 - ELECTRIC CONNECTIONS...

  • Page 114: Removing The Gas Supply Pipes

    2.17.5 - REMOVING THE GAS SUPPLY PIPES To remove the gas supply pipes, once you have extracting the oven from its built-in compartment, just unscrew the pipe fixing nuts using a 12 mm key for the burner and a 15 mm one for the cock (see Fig. 236 and 237). Fig.

  • Page 115: Removing The Gas Ramp

    2.17.6 - REMOVING THE GAS RAMP To remove the ramp: 1 - Slide off the knobs from the cocks (see Fig. 238). Fig. 238 2 - Remove the gas connection pipes (see Chapter entitled 2.17.5 - REMOVING THE GAS SUPPLY PIPES). 3 - Unscrew the ramp fixing screws at the top (see Fig.

  • Page 116: Removing The Hob Assembly

    4 - Unscrew the 2 gas connection support bracket fixing screws (see Fig. 241). Fig. 241 1 - GAS RAMP 2 - GAS CONNECTION SUPPORT FIXING BRACKET 3 - FIXING SCREW - SUPPORT FIXING BRACKET 4 - GAS SUPPLY CONNECTION 5 - TORX SCREWDRIVER 2.17.7 - REMOVING THE HOB ASSEMBLY To remove the hob assembly:...

  • Page 117: Removing The Gas Cocks

    2.17.8 - REMOVING THE GAS COCKS To remove the gas cocks: 1 - Remove the ramp (see Chapter 2.17.6 entitled REMOVING THE RAMP). 2 - Unfasten the cock fixing screws (see Fig. 243). Fig. 243 1 - GAS SUPPLY PIPE TO BURNER 2 - RAMP ASSEMBLY FIXING BRACKET 3 - GAS RAMP...

  • Page 118: Removing The Ignition Micro Assembly

    2.17.9 - REMOVING THE IGNITION MICRO ASSEMBLY To remove the ignition micro switch assembly: 1 - Remove the hob assembly from the oven (see Chapter 2.17.7). 2 - Release the various micro switches from the related cock using a Philips screwdriver (see Fig.

  • Page 119: Steam Ovens

    3 - STEAM OVENS 3.1 - REMOVING THE TANK + STEAM GENERATOR ASSEMBLY To remove the tank + steam generator assembly: 1 - Remove the rear panel (see Fig. 246). Fig. 246 1 - LAMPHOLDER 2 - WATER TANK 3 - EXPANSION CHAMBER 4 - TERMINAL BOARD 5 - ELECTRICAL CONTACTS FOR CONVECTION HEATING...
  • Page 120 3 - Unscrew the overflow pipe fixing screw (see Fig. 248 and 249). Fig. 248 1 - WATER TANK 2 - FIXING SCREW - TANK 3 - STEAM GENERATOR ASSEMBLY 4 - OVERFLOW PIPE FIXING SCREW 5 - FIXING SCREW - STEAM GENERATOR Fig.
  • Page 121 5 - Slide off the water drain pipe from the silicone connection, releasing the fixing clamp with pliers (see Fig. 251). Fig. 251 1 - WATER TANK 2 - STEAM GENERATOR 3 - FIXING CLAMP - SILICONE CONNECTION - TANK 4 - FIXING CLAMP - SILICONE CONNECTION - DRAIN PIPE...

  • Page 122: Removing The "Reed" Level Indicator Switches

    3.2 - REMOVING THE “REED” LEVEL INDICATOR SWITCHES To remove the REED switch assembly: 1 - Remove the rear panel to access the "Full" and "Empty" indicator REEDs (see Fig. 253 and 254). Fig. 253 1 - WATER FILL PIPE 2 - EXPANSION CHAMBER 3 - WATER TANK 4 - “REED”...
  • Page 123 2 - Extract the rubber support for the REED switches using long-nose pliers (see Fig. 255). Fig. 255 1 - LONG-NOSE PLIERS 4 - REED SWITCH SUPPORT FULL INDICATION 3 - Slide the REED switch + rubber support assembly out from the related housings (see Fig.

  • Page 124: Repositioning The "Reed" Level Indicator Switches

    3.3 - REPOSITIONING THE “REED” LEVEL INDICATOR SWITCHES When repositioning the REED switches in their respective silicone rubber support and when repositioning the assembly in the tank, make sure that when re-assembly is complete, the REED switch is fully inserted (see Fig. 259). If the switch is only partially inserted (see Fig.

  • Page 125: Removing The Water Tank

    3.4 - REMOVING THE WATER TANK To remove the water tank: 1 - Remove the tank + steam generator assembly (see chapter 3.1). Fig. 260 1 - WATER TANK 2 - FIXING CLAMP - SILICONE CONNECTION - EXPANSION CHAMBER 3 - FIXING SCREW - TANK 4 - THERMOSTAT ASSEMBLY - STEAM GENERATOR 5 - STEAM GENERATOR...
  • Page 126 3 - Slide the steam outlet pipe for the steam generator assembly out of the expansion chamber (see Fig. 262). Fig. 262 1 - WATER TANK 2 - EXPANSION CHAMBER 3 - GENERATOR STEAM OUTLET PIPE. 4 - STEAM GENERATOR. SOI 02.10 FV 126/142 599 70 59-01...

  • Page 127: Removing The Water Filler Drawer And Control Components

    3.5 - REMOVING THE WATER FILLER DRAWER AND CONTROL COMPONENTS To remove the water filler drawer assembly: 1 - Remove the top oven cover panel. Fig. 263 1 - CONTROL UNIT - KRONOS 2 - POWER BOARD OVC1000 3 - WATER FILLER DRAWER 4 - STEAM GENERATOR CONTROL RELAY 5 - TANGENTIAL COOLING FAN...
  • Page 128 To remove the steam supply relay, proceed as follows: 1 - Detach the connection wires, marking their position. Fig. 265 1 - STEAM SUPPLY RELAY 2 - ELECTRICAL CONNECTIONS TO RELAY 3 - TANGENTIAL FAN MOTOR 2 - Release the relay anchor tabs from the support fixing bracket (see Fig. 266). Fig.

  • Page 129: Water Drain Valve

    3.6 - WATER DRAIN VALVE To access the water drain valve, proceed as follows: 1 - Detach the silicone connection from the water drain pipe, by releasing the retainer clamp. Fig. 268 1 - WATER TANK 2 - SILICONE CONNECTION - 3 - FIXING CLAMP - SILICONE CONNECTION - WATER DRAIN PIPE...
  • Page 130 5 - Detach the drain valve from the front panel by turning it clockwise (see Fig. 270 and 271). Fig. 270 1 - OVEN FRONT PANEL 2 - WATER DRAIN VALVE Fig. 271 1 - OVEN FRONT PANEL 2 - WATER DRAIN VALVE SOI 02.10 FV 130/142 599 70 59-01...
  • Page 131 To reposition the water drain valve: 1 - Insert the valve in the front panel and turn it to hook it in place (see Fig. 272 and 273) Fig. 272 1 - WATER DRAIN VALVE 2 - OVEN FRONT PANEL Fig.

  • Page 132: Accessing The Temperature Sensor In Electronic Models

    3.7 - ACCESSING THE TEMPERATURE SENSOR IN ELECTRONIC MODELS In electronic models, in order to access the temperature control sensor, proceed as follows: 1 - Remove the tank + steam generator assembly as illustrated in chapter 3.1. 2 - Detach the connection connector from the temperature sensor. 3 - Unscrew the fixing screws on the sensor.

  • Page 133: Accessing The Convection Fan

    3.8 - ACCESSING THE CONVECTION FAN To remove the convection fan with snap-on joint: 1 - Remove the tank + steam generator assembly as illustrated in chapter 3.1. 2 - Push the motor anchor tab using a screwdriver (see Fig. 275). 3 - Turn the motor clockwise and extract it (see Fig.
  • Page 134 Fig. 277 1 - MOTOR SUPPORT BRACKET POSITIONED AT THE REAR OF THE OVEN 2 - CONVECTION FAN MOTOR To reposition the convection fan with snap-on joint: 1 - Reposition the anchor tab correctly, lifting it slightly with a Philips screwdriver (see Fig. 278). Fig.
  • Page 135 2 - Insert the motor into the motor support bracket matching the motor tabs to the fixing apertures (see Fig. 279). Fig. 279 1 - MOTOR SUPPORT BRACKET POSITIONED AT THE REAR OF THE OVEN 2 - CONVECTION FAN MOTOR 3 - Turn the motor anti-clockwise to secure it in place (see Fig.

  • Page 136: Electronic Gas Ovens

    4 - ELECTRONIC GAS OVENS To remove the oven from its built-in compartment and disconnect it from the power supply, please refer to chapters 2.1 and 2.2. 4.1 - REMOVING THE CONTROL PANEL In order to remove the control panel (front panel), firstly remove the upper panel (see chapter 2.6): 1.

  • Page 137: Removing The Rear Panel (Various Components And Lampholder)

    4.2 - REMOVING THE REAR PANEL (various components and lampholder) In order to remove the rear panel, simply remove the two upper screws. Once the rear panel has been removed, the following components are accessible: the lampholder, the grill heating element, the ignitor, the spit motor, the electronic board, the nozzle support and the terminal board with cable clamp.

  • Page 138: Upper Panels (Control Components And Boards)

    4.2.4 - UPPER PANELS (control components and boards) There are two panels in the upper part. A panel to access the electronic boards and the control components and a larger panel that covers the tangential cooling fan. 4.2.6.1 - UPPER PANEL (control components and boards) Once the upper panel has been removed, you can access the control components (oven thermostat, function selector, electronic programmer, indicator lights, etc.) 1.

  • Page 139: Removing The Gas Solenoid Valve Assembly

    4.2.5 - REMOVING THE GAS SOLENOID VALVE ASSEMBLY To remove the gas solenoid valve assembly: 1. Remove the upper panels (see chapter 4.2.6). 2. Detach the wires from the solenoid valve assembly (see Fig. 286). 3. Unscrew the gas supply hose fixing nut (see Fig. 286). 4.

  • Page 140: Removing The Oven Burner

    4.3 - REMOVING THE OVEN BURNER To remove the oven burner: 1. Open the oven door. 2. Remove the cover from the bottom of the oven. 3. Unfasten the burner fixing screws (see Fig. 288). 4. Extract the burner, avoiding any stress on the connector cable to the spark plug.

  • Page 141: Organisation Of Access Plus Service Manuals

    5 - ORGANISATION OF ACCESS PLUS SERVICE MANUALS In view of the quantity of theoretical, technical and practical information regarding the various combinations for the structure of the ACCESS PLUS/KRONOS system, this information has been subdivided into Service Manuals describing the general concepts, and separate Service Manuals containing specific information regarding each group of appliances.

  • Page 142: Revisions

    6 - REVISIONS REVISION DATE 09/2008 - Added Chapter 2.4.9 - REMOVING THE CONVECTION FAN WITH SNAP-ON JOINT on page 32. 02/2010 - Amended Chapter 2.12 - ADJUSTING THE "HINGED" DOOR ALIGNMENT on pages 93-97.. - Corrected Chapter 2.14 - THERMAL GLAZING on page 99. - Added Chapter 2.6.1 - NEW ONE-PIECE OVEN COVER.

Table of Contents