Advertisement
ENGLAND
DESCRIPTION
(starts at
pase
3/)
'I
2
?
4
5
6
7
I
o
10
11
t1
Handles
Accelerator
Dash-board
Rod
Transport wheels
Hoeing blades
Protection guard
Fuel
tank
Spark plug
Engine startfrip
Reduction
gbar
Clutch lever
13
Reverse lever
14
Side
disk
ASSEMBLY
(storts at
pase
3il
OPERATION
{starts at
pase
34
Before you start working, make sure
to
remove any objects or obstacles that may have been
le{l
on the
lawn.
The operator is responsible
for
the safety
oJ
other people
in
the working area.
lsbns
al
page 32/
Once the machine has been set up properly, start the engine
as
iollows:
a)Engines
with choke system:
if
the model
is
equipped with an accelerator, when the engine
is
cold, position the accelerator lever (2-Fig.E)
onSTART
Engines
with
p(imer system:
Press the
f
uel-enrichmenl pump located on the carburettor 3
or
4 times.if the model
is
equipped with an accelerator, position the accelerator lever (2-Fig.E) on MAX.
/slarts al
page 32)
b)
Grip
lhe engine start grip
(1
0)
and
pull
the starler
rope
gently
until you feel
the resistance caused
by
compression. Release the handle; then
give
the starter
rope a
sharp
Hii tunn",
intormation
and explanations.
read
carelully the user
instruction
manual
of
the engine.
(stuns
ot
page 32)
Before starting
work,
it is
necessary to
carry
out the following:
-
set lhe
trasport
wheels (5) upwards
/snns
ot
poge 32)
lnitially position the hook (15)
of
the forward drive cable and the hook (16)
of
the
reverse clutch cable
in
the holes
(ll")
of
the
respective handles (12-13).
should the
handle
aclion
not
follow the cutter clutch, position
the
hook into hole
(l')
of
the handle, while on the
conlrary
insert
it
into hole
(lll')
should the cutlers remain
engaged even on release ol the handle itself.
(slarls
ol
poge 32)
WABNING
!
Never
keep
the
two
handles
(12-13)
activated
at
the
same
time.
It
may
cause
damage to
the
betts
and
pulleys.
/stuns
ot
page 32)
WHENTHE ENGINE
lS
ON:
in
order to make
the
tiiler blades (6)
run,
handle (12)
rnust be
depressed. When working
with the tiller, keep
the handle depressed.
l{
the
handle
is reieased,
the
tiller blades will come to
a
stop.
Depress the skid
in
order
to
work
in
deplh
and decrease the pressure to move {orwards.
f
"-l
1-.l]
fttarts
atpoge
32)
i
]
l:4.
|
*=ua"rr-o=AR:
for ensaging the reverse-gear, onty handte
(1
3) must be actuated.
!,.
l
l'7
|
Howtostoptheengine:{orthispurpose,shifttheacceleratedleverintoSTOPposition
lstuns
ot
page 32)
The four cutter stars (6) can be pulled off, and the combination
of
cutters allows working widths from 25 to
55
cms.
For
assembly, introduce the blade star
(6) to
the rotary
shaJt (N)
and make the two holes (P) match: then introduce pin (R)
by
fastening
it
with the respectrve spring. Make
sure that the hoeing blades are assembled
in
the
right direction,
i.e.
the cutting angle showing forward.
Advertisement
