VL-DM200 MENU PRESS TALK Thank you for purchasing a Panasonic product. Please read this manual before using the unit and save for future reference. The unit can be paired to the VL-SDM200BX (Base Unit: VL-MDM200BX). Before using the unit, it must be charged and paired to the Base Unit (page 9, 10).
Table of Contents Introduction Product information ..........3 Accessory information ........3 Important Information For your safety ............5 Important safety instructions .......7 For best performance .........7 Other information ..........8 Getting Started Charging the Wireless Monitor ......9 Pairing to the Base Unit ........10 Canceling the Wireless Monitor ......11 General Information Specifications ............12...
Introduction Product information The unit is an additional Wireless Monitor designed to be used with the Panasonic Wireless Door Camera (described in this manual as VL-SDM200BX). In order to use the unit, it must be paired to the Base Unit of the VL-SDM200BX.
Page 4
Introduction Additional/replacement accessories – Battery pack for Wireless Monitor: CGA-LB102 *1 As of February, 2013. Note: R Design and specifications are subject to change without notice. R The illustrations in these instructions may vary slightly from the actual product. License: R Portions of this software are based in part on the work of the Independent JPEG Group.
Important Information For your safety To prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING Power connection R Use only the power source marked on the unit. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
Page 6
Important Information – If the Charger or the Wireless Monitor has been exposed to rain or water, or liquid has been spilled into the unit, do not use a microwave oven to speed up the drying process of any parts of the unit to avoid permanent damage.
– Electric shock or radio wave interference occurs. – The power is turned off during use. R Panasonic may not be liable for damages due to external factors such as power failures. Location/avoiding noise (Base Unit/Wireless Camera/Wireless Monitor) The Base Unit (A), Wireless Camera (B), and Wireless Monitor (C) use radio waves to communicate with each other.
Important Information R The unit should not be exposed to direct sunlight. R The unit is not waterproof. Do not get the unit wet. Failure to do this may cause malfunction. R Do not place heavy objects on top of the unit. R When you leave the unit unused for a long period of time, unplug it from the power outlet.
Getting Started Charging the Wireless Monitor Charge the Wireless Monitor for at least 30 minutes before pairing it to the Base Unit for the first time (page 10). After pairing, replace the Wireless Monitor and complete charging. *1 This time is a guide for the time required when the temperature is 20 °C. When the surrounding temperature is low, the time required for charging may increase.
Getting Started – Recharge the battery pack before using the Wireless Monitor again. Pairing to the Base Unit R The Wireless Monitor ( ) can be used by pairing it to the Base Unit ( of the Wireless Door Camera. : Plug the AC adaptor of the Base Unit into the power outlet.
Getting Started Canceling the Wireless Monitor R These operations can be performed on all paired Wireless Monitors. R The Wireless Monitor performing these operations cannot be unpaired. Press MMENUN. Select “ALL SETTINGS” by pressing arrow keys (MDN, MCN, MFN, or MEN), then press M N (Monitor button) (“OK”).
General Information Specifications Wireless Monitor (VL-DM200BX) n Power supply: Lithium ion battery (part number: CGA-LB102) n Dimensions (Height ´ Width ´ Depth): Approx. 21 mm ´ 126 mm ´ 59 mm (excluding protruding sections) – When using with the Charger: approx.
Page 13
General Information n Weight: Approx. 114 g n Operating temperature: 5 °C to 40 °C n Operating humidity: Up to 90 % RH (Relative Humidity) non condensing...